Lines Matching refs:rdev_err
122 rdev_err(rdev, "no constraints\n"); in regulator_ops_is_valid()
431 rdev_err(rdev, "voltage operation not allowed\n"); in regulator_check_voltage()
441 rdev_err(rdev, "unsupportable voltage range: %d-%duV\n", in regulator_check_voltage()
481 rdev_err(rdev, "Restricting voltage, %u-%uuV\n", in regulator_check_consumers()
496 rdev_err(rdev, "current operation not allowed\n"); in regulator_check_current_limit()
507 rdev_err(rdev, "unsupportable current range: %d-%duA\n", in regulator_check_current_limit()
526 rdev_err(rdev, "invalid mode %x specified\n", *mode); in regulator_mode_constrain()
531 rdev_err(rdev, "mode operation not allowed\n"); in regulator_mode_constrain()
1002 rdev_err(rdev, "failed to set load %d: %pe\n", in drms_uA_update()
1048 rdev_err(rdev, "failed to get optimum mode @ %d uA %d -> %d uV: %pe\n", in drms_uA_update()
1055 rdev_err(rdev, "failed to set optimum mode %x: %pe\n", in drms_uA_update()
1077 rdev_err(rdev, "failed to enabled/disable: %pe\n", ERR_PTR(ret)); in __suspend_set_state()
1084 rdev_err(rdev, "failed to set voltage: %pe\n", ERR_PTR(ret)); in __suspend_set_state()
1092 rdev_err(rdev, "failed to set mode: %pe\n", ERR_PTR(ret)); in __suspend_set_state()
1227 rdev_err(rdev, in machine_constraints_voltage()
1257 rdev_err(rdev, in machine_constraints_voltage()
1292 rdev_err(rdev, "invalid voltage constraints\n"); in machine_constraints_voltage()
1317 rdev_err(rdev, in machine_constraints_voltage()
1349 rdev_err(rdev, "Invalid current constraints\n"); in machine_constraints_current()
1362 rdev_err(rdev, "Failed to set current constraint, %d\n", ret); in machine_constraints_current()
1446 rdev_err(rdev, "failed to set input limit: %pe\n", ERR_PTR(ret)); in set_machine_constraints()
1455 rdev_err(rdev, "failed to set suspend state: %pe\n", ERR_PTR(ret)); in set_machine_constraints()
1462 rdev_err(rdev, "no set_mode operation\n"); in set_machine_constraints()
1468 rdev_err(rdev, "failed to set initial mode: %pe\n", ERR_PTR(ret)); in set_machine_constraints()
1483 rdev_err(rdev, "failed to set ramp_delay: %pe\n", ERR_PTR(ret)); in set_machine_constraints()
1491 rdev_err(rdev, "failed to set pull down: %pe\n", ERR_PTR(ret)); in set_machine_constraints()
1499 rdev_err(rdev, "failed to set soft start: %pe\n", ERR_PTR(ret)); in set_machine_constraints()
1526 rdev_err(rdev, "failed to set over current protection: %pe\n", in set_machine_constraints()
1538 rdev_err(rdev, "failed to set over current limits: %pe\n", in set_machine_constraints()
1552 rdev_err(rdev, "failed to set over voltage limits %pe\n", in set_machine_constraints()
1566 rdev_err(rdev, "failed to set under voltage limits %pe\n", in set_machine_constraints()
1580 rdev_err(rdev, "failed to set temperature limits %pe\n", in set_machine_constraints()
1594 rdev_err(rdev, "failed to set active discharge: %pe\n", ERR_PTR(ret)); in set_machine_constraints()
1644 rdev_err(rdev, "failed to enable: %pe\n", ERR_PTR(ret)); in set_machine_constraints()
2811 rdev_err(rdev, "Enabled check timed out\n"); in _regulator_do_enable()
2876 rdev_err(rdev, "Underflow of regulator enable count\n"); in _regulator_handle_consumer_disable()
2932 rdev_err(rdev, "is_enabled() failed: %pe\n", ERR_PTR(ret)); in _regulator_enable()
3036 rdev_err(rdev, "failed to disable: %pe\n", ERR_PTR(ret)); in _regulator_disable()
3106 rdev_err(rdev, "failed to force disable: %pe\n", ERR_PTR(ret)); in _regulator_force_disable()
3187 rdev_err(rdev, "Deferred disable failed: %pe\n", in regulator_disable_work()
4241 rdev_err(rdev, "Not all coupled regulators registered\n"); in regulator_balance_voltage()
4344 rdev_err(rdev, "The suspend voltage can't be changed!\n"); in _regulator_set_suspend_voltage()
4556 rdev_err(rdev, in regulator_get_voltage_rdev()
5601 rdev_err(rdev, in regulator_find_coupler()
5626 rdev_err(rdev, "coupler mismatch with %s\n", in regulator_resolve_coupling()
5679 rdev_err(rdev, "failed to detach from coupler: %pe\n", in regulator_remove_coupling()
5725 rdev_err(rdev, "failed to get coupler: %pe\n", ERR_PTR(err)); in regulator_init_coupling()
5736 rdev_err(rdev, in generic_coupler_attach()
5742 rdev_err(rdev, in generic_coupler_attach()
5929 rdev_err(rdev, "Failed to request enable GPIO: %pe\n", in regulator_register()
6512 rdev_err(rdev, "couldn't disable: %pe\n", ERR_PTR(ret)); in regulator_late_cleanup()