Searched refs:LCR (Results 1 – 8 of 8) sorted by relevance
| /drivers/power/reset/ |
| A D | qnap-poweroff.c | 60 writel(0x83, UART1_REG(LCR)); in qnap_power_off()
63 writel(0x03, UART1_REG(LCR)); in qnap_power_off()
|
| /drivers/net/hamradio/ |
| A D | yam.c | 154 #define LCR(iobase) (iobase+3) macro
294 outb(LCR_DLAB | LCR_BIT5, LCR(iobase)); in fpga_reset()
298 outb(LCR_BIT5, LCR(iobase)); in fpga_reset()
466 outb(LCR_DLAB | LCR_BIT8, LCR(dev->base_addr)); in yam_set_uart()
469 outb(LCR_BIT8, LCR(dev->base_addr)); in yam_set_uart()
|
| A D | baycom_ser_fdx.c | 97 #define LCR(iobase) (iobase+3) macro
173 outb(0x81, LCR(dev->base_addr)); /* DLAB = 1 */ in ser12_set_divisor()
176 outb(0x01, LCR(dev->base_addr)); /* word length = 6 */ in ser12_set_divisor()
|
| A D | baycom_ser_hdx.c | 83 #define LCR(iobase) (iobase+3) macro
158 outb(0x81, LCR(dev->base_addr)); /* DLAB = 1 */ in ser12_set_divisor()
161 outb(0x01, LCR(dev->base_addr)); /* word length = 6 */ in ser12_set_divisor()
|
| /drivers/usb/serial/ |
| A D | io_16654.h | 35 #define LCR 3 // Line Control Register macro
|
| A D | io_edgeport.c | 2217 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, LCR, LCR_DL_ENABLE); in send_cmd_write_baud_rate()
2224 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, LCR, in send_cmd_write_baud_rate()
2298 regNum == LCR) { in send_cmd_write_uart_register()
2461 status = send_cmd_write_uart_register(edge_port, LCR, in change_port_settings()
|
| /drivers/tty/serial/8250/ |
| A D | 8250_pci.c | 1355 u8 LCR, val; in pci_quatech_rqopr() local
1357 LCR = inb(base + UART_LCR); in pci_quatech_rqopr()
1360 outb(LCR, base + UART_LCR); in pci_quatech_rqopr()
1367 u8 LCR; in pci_quatech_wqopr() local
1369 LCR = inb(base + UART_LCR); in pci_quatech_wqopr()
1373 outb(LCR, base + UART_LCR); in pci_quatech_wqopr()
1379 u8 LCR, val, qmcr; in pci_quatech_rqmcr() local
1381 LCR = inb(base + UART_LCR); in pci_quatech_rqmcr()
1387 outb(LCR, base + UART_LCR); in pci_quatech_rqmcr()
1395 u8 LCR, val; in pci_quatech_wqmcr() local
[all …]
|
| /drivers/tty/serial/ |
| A D | men_z135_uart.c | 96 #define LCR(x) (((x) >> MEN_Z135_LCR_SHIFT) & 0xff) macro
651 lcr = LCR(conf_reg); in men_z135_set_termios()
|
Completed in 28 milliseconds