Searched refs:always (Results 1 – 25 of 61) sorted by relevance
123
| /drivers/clk/starfive/ |
| A D | Kconfig | 45 tristate "StarFive JH7110 always-on clock support"
49 Say yes here to support the always-on clock controller on the
|
| /drivers/atm/ |
| A D | nicstarmac.copyright | 25 * IDT always receives data into a small buffer, then large buffers
26 * as needed. This means that data must always be copied to create
|
| /drivers/eisa/ |
| A D | Makefile | 4 always-$(CONFIG_EISA) += devlist.h
|
| /drivers/usb/core/ |
| A D | Kconfig | 8 Say Y here if you want the USB core to always announce the
40 This almost always works, but when it fails it can take a long time.
116 The default value Linux has always had is 2 seconds. Change
|
| /drivers/block/ |
| A D | rnull.rs | 67 #[inline(always)]
|
| /drivers/ata/pata_parport/ |
| A D | Kconfig | 20 before 1999 were Series 5) Series 5 drives will NOT always have the
33 on the bottom of the drive. Series 5 drivers don't always have it
|
| /drivers/video/console/ |
| A D | Kconfig | 111 always select the first framebuffer driver that is loaded. The latter
114 You can always override the automatic selection of the primary device
|
| /drivers/base/ |
| A D | Kconfig | 59 the devtmpfs filesystem always needs to be mounted manually
97 you should always prevent this and say Y here. There are only two
241 late_initcall() if !CONFIG_MODULES. You should almost always want to
|
| /drivers/pinctrl/starfive/ |
| A D | Kconfig | 48 Say yes here to support always-on pin control on the StarFive JH7110 SoC.
|
| /drivers/devfreq/ |
| A D | Kconfig | 47 This governor always returns UINT_MAX as frequency so that
55 This governor always returns 0 as frequency so that
|
| /drivers/base/firmware_loader/ |
| A D | Kconfig | 108 The direct filesystem lookup for firmware is always used first now.
115 If the custom fallback mechanism is used userspace must always
219 It is also not always useful, so on such platforms we have the
|
| /drivers/platform/x86/ |
| A D | fujitsu-laptop.c | 723 int poweron = FUNC_LED_ON, always = FUNC_LED_ON; in logolamp_set() local
730 always = FUNC_LED_OFF; in logolamp_set()
736 return call_fext_func(device, FUNC_LEDS, 0x1, LOGOLAMP_ALWAYS, always); in logolamp_set()
|
| /drivers/net/team/ |
| A D | Kconfig | 22 Basic mode where packets are transmitted always by all suitable ports.
|
| /drivers/soc/fsl/qbman/ |
| A D | Kconfig | 66 DQRR, data and context stashing always on.
|
| /drivers/rpmsg/ |
| A D | Kconfig | 5 # RPMSG always gets selected by whoever wants it
|
| /drivers/net/ethernet/atheros/ |
| A D | Kconfig | 27 ethernet support, then you should always answer Y to this.
|
| /drivers/net/wireless/ti/wlcore/ |
| A D | debugfs.c | 879 wl->conf.rx_streaming.always = value; in rx_streaming_always_write()
902 "%d\n", wl->conf.rx_streaming.always); in rx_streaming_always_read()
1295 DEBUGFS_ADD_PREFIX(rx_streaming, always, streaming); in wl1271_debugfs_add_files()
|
| A D | conf.h | 1043 u8 always; member
|
| /drivers/usb/musb/ |
| A D | Kconfig | 129 bool 'Disable DMA (always use PIO)'
|
| /drivers/staging/most/Documentation/ |
| A D | driver_usage.txt | 224 written to 'subbuffer_size' and hardware will always expect two isochronous
236 fit its constraints, it is recommended to always double check the
|
| /drivers/gpu/drm/ |
| A D | Makefile | 240 always-$(CONFIG_DRM_HEADER_TEST) += \
|
| /drivers/misc/eeprom/ |
| A D | Kconfig | 21 Unless you like data loss puzzles, always be sure that any chip
|
| /drivers/iommu/ |
| A D | Kconfig | 6 # IOMMU_API always gets selected by whoever wants it.
117 Untrusted devices always use this mode, with an additional layer of
|
| /drivers/net/arcnet/ |
| A D | Kconfig | 77 have always used the old ARCnet driver without knowing what type of
|
| /drivers/gpu/drm/i915/ |
| A D | Kconfig.profile | 20 to ensure that we are always signaled and our userspace is able to
|
Completed in 815 milliseconds
123