Searched refs:selecting (Results 1 – 25 of 26) sorted by relevance
12
23 This pin controller allows selecting the mux function for35 This pin controller allows selecting the mux function for47 This pin controller allows selecting the mux function for59 This pin controller allows selecting the mux function for74 This pin controller allows selecting the mux function for86 This pin controller allows selecting the mux function for
617 !hostdata->selecting) { in maybe_release_dma_irq()987 hostdata->selecting = cmd; in NCR5380_select()1016 if (!hostdata->selecting) { in NCR5380_select()1065 if (!hostdata->selecting) { in NCR5380_select()1150 if (!hostdata->selecting) in NCR5380_select()1187 if (!hostdata->selecting) { in NCR5380_select()1223 if (!hostdata->selecting) in NCR5380_select()1225 hostdata->selecting = NULL; in NCR5380_select()2269 hostdata->selecting = NULL; in NCR5380_abort()2340 if (hostdata->selecting) { in bus_reset_cleanup()[all …]
421 if (hostdata->selecting || hostdata->connected) { in DEF_SCSI_QCMD()543 hostdata->selecting = cmd; in DEF_SCSI_QCMD()795 cmd = (struct scsi_cmnd *) hostdata->selecting; /* get a valid cmd */ in wd33c93_intr()796 hostdata->selecting = NULL; in wd33c93_intr()828 (struct scsi_cmnd *) hostdata->selecting; in wd33c93_intr()829 hostdata->selecting = NULL; in wd33c93_intr()1291 if (hostdata->selecting) { in wd33c93_intr()1292 cmd = (struct scsi_cmnd *) hostdata->selecting; in wd33c93_intr()1293 hostdata->selecting = NULL; in wd33c93_intr()1533 hostdata->selecting = NULL; in wd33c93_host_reset()[all …]
38 selecting, enumerator175 state->phase = selecting; in mac53c94_start()247 case selecting: in mac53c94_interrupt()
227 volatile struct scsi_cmnd *selecting; /* trying to select this command */ member
306 selecting = 0x0002, /* target is being selected */ enumerator901 if (acp->phase & selecting) { in setup_expected_interrupts()1511 acp->phase |= selecting; in busfree_run()1545 acp->phase &= ~(selecting | not_issued); in seldo_run()1589 acp->phase &= ~selecting; in selto_run()2240 (aha152x_priv(CURRENT_SC)->phase & selecting)) { in update_state()2492 phase & selecting ? "selecting|" : "", in show_command()2548 if (phase & selecting) in get_command()
217 struct scsi_cmnd *selecting; /* Cmnd to be connected */ member
106 selecting, enumerator758 case selecting: in start_phase()1111 if (ms->phase > selecting && (in_8(&mr->bus_status1) & BS1_BSY)) { in handle_error()1542 case selecting: in cmd_complete()
163 ; Basically tell the selecting device that there's nothing here
199 ; Basically tell the selecting device that there's nothing here
16 This pin controller allows selecting the mux function for
28 The built-in microphone is enabled by selecting USB Audio support.
143 ACPI selecting value 2 is analogous to selecting value 0.
74 Note: selecting this option may adversely impact
35 Say Y here to enable selecting drivers for V4L devices that
155 debug and trace capabilities. On selecting m, the module name
8 Say Y here if you want to enable selecting webcams based
238 by selecting USB_DWC2 or USB_DWC3 options.
128 If selecting USB_GADGET_DEBUG_FILES this value may be set by
12 Say Y here to enable selecting AM/FM radio adapters.
636 This pin controller allows selecting the mux function for
38 you very likely use this. It is selected automatically by selecting
471 * Upper four bits are the device id. The ONEBIT is set when the re/selecting
1865 * Upper four bits are the device id. The ONEBIT is set when the re/selecting
156 * selecting, keep polling the current channel until
Completed in 50 milliseconds