Searched refs:speed_mode (Results 1 – 7 of 7) sorted by relevance
| /drivers/cpufreq/ |
| A D | pmac64-cpufreq.c | 153 if (speed_mode < g5_pmode_cur) in g5_scom_switch_freq()
154 g5_switch_volt(speed_mode); in g5_scom_switch_freq()
183 if (speed_mode > g5_pmode_cur) in g5_scom_switch_freq()
184 g5_switch_volt(speed_mode); in g5_scom_switch_freq()
186 g5_pmode_cur = speed_mode; in g5_scom_switch_freq()
258 if (speed_mode < g5_pmode_cur) in g5_pfunc_switch_freq()
259 g5_switch_volt(speed_mode); in g5_pfunc_switch_freq()
262 if (speed_mode == CPUFREQ_HIGH) in g5_pfunc_switch_freq()
287 if (speed_mode > g5_pmode_cur) in g5_pfunc_switch_freq()
288 g5_switch_volt(speed_mode); in g5_pfunc_switch_freq()
[all …]
|
| A D | pmac32-cpufreq.c | 333 static int do_set_cpu_speed(struct cpufreq_policy *policy, int speed_mode) in do_set_cpu_speed() argument
338 if (speed_mode == CPUFREQ_LOW && in do_set_cpu_speed()
346 set_speed_proc(speed_mode == CPUFREQ_LOW); in do_set_cpu_speed()
347 if (speed_mode == CPUFREQ_HIGH && in do_set_cpu_speed()
353 cur_freq = (speed_mode == CPUFREQ_HIGH) ? hi_freq : low_freq; in do_set_cpu_speed()
|
| /drivers/mmc/core/ |
| A D | bus.c | 304 const char *speed_mode = ""; in mmc_add_card() local
349 speed_mode = "high speed "; in mmc_add_card()
351 speed_mode = "UHS-I speed "; in mmc_add_card()
353 speed_mode = "UHS-II speed "; in mmc_add_card()
355 speed_mode = "high speed DDR "; in mmc_add_card()
357 speed_mode = "HS200 "; in mmc_add_card()
359 speed_mode = "HS400 Enhanced strobe "; in mmc_add_card()
361 speed_mode = "HS400 "; in mmc_add_card()
369 mmc_hostname(card->host), speed_mode, type); in mmc_add_card()
372 mmc_hostname(card->host), speed_mode, in mmc_add_card()
|
| /drivers/i2c/busses/ |
| A D | i2c-hisi.c | 417 u32 reg, sda_hold_cnt, speed_mode; in hisi_i2c_configure_bus() local
424 speed_mode = HISI_I2C_FAST_SPEED_MODE; in hisi_i2c_configure_bus()
428 speed_mode = HISI_I2C_HIGH_SPEED_MODE; in hisi_i2c_configure_bus()
433 speed_mode = HISI_I2C_STD_SPEED_MODE; in hisi_i2c_configure_bus()
443 reg |= FIELD_PREP(HISI_I2C_FRAME_CTRL_SPEED_MODE, speed_mode); in hisi_i2c_configure_bus()
|
| A D | i2c-nomadik.c | 1042 unsigned int mask, speed_mode; in nmk_i2c_eyeq5_probe() local
1053 speed_mode = I2C_EYEQ5_SPEED_FAST; in nmk_i2c_eyeq5_probe()
1055 speed_mode = I2C_EYEQ5_SPEED_FAST_PLUS; in nmk_i2c_eyeq5_probe()
1057 speed_mode = I2C_EYEQ5_SPEED_HIGH_SPEED; in nmk_i2c_eyeq5_probe()
1061 mask, speed_mode << __fls(mask)); in nmk_i2c_eyeq5_probe()
|
| /drivers/pci/hotplug/ |
| A D | shpchp_hpc.c | 621 u8 speed_mode = (pi == 2) ? (sec_bus_reg & 0xF) : (sec_bus_reg & 0x7); in shpc_get_cur_bus_speed() local
623 if ((pi == 1) && (speed_mode > 4)) { in shpc_get_cur_bus_speed()
628 switch (speed_mode) { in shpc_get_cur_bus_speed()
|
| /drivers/net/phy/ |
| A D | motorcomm.c | 1257 int speed_mode, duplex; in yt8521_adjust_status() local
1267 speed_mode = status & YTPHY_SSR_SPEED_MASK; in yt8521_adjust_status()
1269 switch (speed_mode) { in yt8521_adjust_status()
2709 int speed_mode; in yt8821_adjust_status() local
2712 speed_mode = val & YTPHY_SSR_SPEED_MASK; in yt8821_adjust_status()
2713 switch (speed_mode) { in yt8821_adjust_status()
|
Completed in 63 milliseconds