| /drivers/video/fbdev/riva/ |
| A D | riva_hw.h | 292 #ifdef Control
293 #undef Control
295 U032 Control; member
323 #ifdef Control
324 #undef Control
326 U032 Control; member
|
| /drivers/scsi/aic7xxx/ |
| A D | aic79xx.reg | 408 * Interrupt Control
424 * Data FIFO Control
501 * Arbiter Control
657 * ROM Control
839 * PCI-X Control
2522 * CRC Control
2953 * CMC SG Control
2968 * CMD SCB Control
3069 * Board Control
3217 * DSP REQ Control
[all …]
|
| A D | aic7xxx.reg | 65 * SCSI Sequence Control (p. 3-11).
82 * SCSI Transfer Control 0 Register (pp. 3-13).
98 * SCSI Transfer Control 1 Register (pp. 3-14,15).
115 * SCSI Control Signal Read Register (p. 3-15).
144 * SCSI Control Signal Write Register (p. 3-16).
174 * SCSI Rate Control (p. 3-17).
547 * Serial EEPROM Control (p. 4-92 in 7870 Databook)
584 * SCSI Block Control (p. 3-32)
604 * Sequencer Control (p. 3-33)
734 * Board Control (p. 3-43)
[all …]
|
| /drivers/pci/pwrctrl/ |
| A D | Kconfig | 15 tristate "PCI Power Control driver for PCI slots"
18 Say Y here to enable the PCI Power Control driver to control the power
|
| /drivers/clk/keystone/ |
| A D | Kconfig | 10 tristate "TI System Control Interface clock drivers"
15 This adds the clock driver support over TI System Control Interface.
|
| /drivers/soc/aspeed/ |
| A D | Kconfig | 13 Control LPC firmware cycle mappings through ioctl()s. The driver
43 Control ASPEED P2A VGA MMIO to BMC mappings through ioctl()s. The
|
| /drivers/net/ethernet/atheros/atlx/ |
| A D | atl2.c | 2177 u32 i, Control; in get_permanent_address() local
2198 Addr[0] = Control; in get_permanent_address()
2201 Addr[1] = Control; in get_permanent_address()
2205 Register = (u16) (Control >> 16); in get_permanent_address()
2236 Addr[0] = Control; in get_permanent_address()
2238 Addr[1] = Control; in get_permanent_address()
2240 } else if ((Control & 0xff) == 0x5A) { in get_permanent_address()
2242 Register = (u16) (Control >> 16); in get_permanent_address()
2710 u32 Control; in atl2_read_eeprom() local
2722 if (Control & VPD_CAP_VPD_FLAG) in atl2_read_eeprom()
[all …]
|
| /drivers/firmware/arm_scmi/ |
| A D | Kconfig | 2 menu "ARM System Control and Management Interface Protocol"
5 tristate "ARM System Control and Management Interface (SCMI) Message Protocol"
8 ARM System Control and Management Interface (SCMI) protocol is a
|
| /drivers/clk/baikal-t1/ |
| A D | Kconfig | 3 bool "Baikal-T1 Clocks Control Unit interface"
7 Clocks Control Unit is the core of Baikal-T1 SoC System Controller
|
| /drivers/clk/uniphier/ |
| A D | Kconfig | 9 Say Y if you want to control clocks provided by System Control
|
| /drivers/firmware/ |
| A D | Kconfig | 12 tristate "ARM System Control and Power Interface (SCPI) Message Protocol"
16 System Control and Power Interface (SCPI) Message Protocol is
18 Cores(AP) and the System Control Processor(SCP). The MHU peripheral
225 tristate "TI System Control Interface (TISCI) Message Protocol"
229 TI System Control Interface (TISCI) Message Protocol is used to manage
|
| /drivers/platform/x86/intel/uncore-frequency/ |
| A D | Kconfig | 6 menu "Intel Uncore Frequency Control"
|
| /drivers/reset/ |
| A D | Kconfig | 234 Support for USBPHY Control found on RZ/G2L family. It mainly
241 Support for USB2PHY Port reset Control found on the RZ/V2H(P) SoC
318 tristate "TI System Control Interface (TI-SCI) reset driver"
321 This enables the reset driver support over TI System Control Interface
363 Say Y if you want to control reset signals provided by System Control
|
| /drivers/scsi/mpt3sas/mpi/ |
| A D | mpi2_init.h | 122 U32 Control; /*0x3C */ member
274 U32 Control; /*0x3C */ member
|
| /drivers/media/cec/ |
| A D | Kconfig | 31 Enable support for HDMI CEC (Consumer Electronics Control),
|
| /drivers/net/ethernet/freescale/dpaa2/ |
| A D | Kconfig | 21 Enable Priority-Based Flow Control (PFC) support for DPAA2 Ethernet
|
| /drivers/pmdomain/mediatek/ |
| A D | Kconfig | 26 Control Processor System (SCPSYS) has several power management related
|
| /drivers/message/fusion/lsi/ |
| A D | mpi_init.h | 89 U32 Control; /* 14h */ member
276 U32 Control; /* 14h */ member
|
| A D | mpi_history.txt | 79 * 08-19-04 01.05.01 Added defines for Host Buffer Access Control doorbell.
444 * Added Device Self Test to Control Flags of SAS IO Unit
720 * Control request, and added a new operation code.
722 * and Remove Device operations to SAS IO Unit Control.
723 * Added DevHandle field to SAS IO Unit Control request and
726 * Unit Control request.
729 * fields to SAS IO Unit Control Request.
|
| A D | mpi_raid.h | 187 U32 Control; /* 14h */ member
|
| /drivers/usb/gadget/ |
| A D | Kconfig | 250 bool "Abstract Control Model (CDC ACM)"
270 bool "Network Control Model (CDC NCM)"
282 bool "Ethernet Control Model (CDC ECM)"
288 The "Communication Device Class" (CDC) Ethernet Control Model.
294 bool "Ethernet Control Model (CDC ECM) subset"
|
| /drivers/peci/ |
| A D | Kconfig | 6 The Platform Environment Control Interface (PECI) is an interface
|
| /drivers/peci/controller/ |
| A D | Kconfig | 30 Say Y here if you want support for the Platform Environment Control
|
| /drivers/usb/class/ |
| A D | Kconfig | 12 Communication Device Class Abstract Control Model interface.
|
| /drivers/soc/fsl/ |
| A D | Kconfig | 51 (Run Control and Power Management), which performs all device-level
|