Lines Matching refs:config
86 gpio_device->config = OUTPUT_PUSH_PULL; in board_set_gpio_default()
106 gpio_config_t *config = (gpio_config_t *)&device.config; in board_parse_gpio() local
142 *config = INPUT_PULL_DOWN; in board_parse_gpio()
144 *config = INPUT_PULL_UP; in board_parse_gpio()
146 *config = INPUT_HIGH_IMPEDANCE; in board_parse_gpio()
151 *config = OUTPUT_PUSH_PULL; in board_parse_gpio()
153 *config = OUTPUT_OPEN_DRAIN_PULL_UP; in board_parse_gpio()
155 *config = OUTPUT_OPEN_DRAIN_NO_PULL; in board_parse_gpio()
159 *config = IRQ_MODE; in board_parse_gpio()
162 *config = INPUT_PULL_DOWN; in board_parse_gpio()
164 *config = INPUT_PULL_UP; in board_parse_gpio()
166 *config = INPUT_HIGH_IMPEDANCE; in board_parse_gpio()
181 *config = ANALOG_MODE; in board_parse_gpio()
224 uart_device->config.baud_rate = 115200; in board_set_uart_default()
225 uart_device->config.data_width = DATA_WIDTH_8BIT; in board_set_uart_default()
226 uart_device->config.flow_control = FLOW_CONTROL_DISABLED; in board_set_uart_default()
227 uart_device->config.parity = NO_PARITY; in board_set_uart_default()
228 uart_device->config.stop_bits = STOP_BITS_1; in board_set_uart_default()
229 uart_device->config.mode = MODE_TX_RX; in board_set_uart_default()
240 uart_config_t *config = (uart_config_t *)&device.config; in board_parse_uart() local
268 config->data_width = DATA_WIDTH_5BIT; in board_parse_uart()
271 config->data_width = DATA_WIDTH_6BIT; in board_parse_uart()
274 config->data_width = DATA_WIDTH_7BIT; in board_parse_uart()
277 config->data_width = DATA_WIDTH_8BIT; in board_parse_uart()
287 config->baud_rate = temp->valueint; in board_parse_uart()
296 config->stop_bits = STOP_BITS_1; in board_parse_uart()
299 config->stop_bits = STOP_BITS_2; in board_parse_uart()
309 config->flow_control = FLOW_CONTROL_DISABLED; in board_parse_uart()
313 config->flow_control = FLOW_CONTROL_CTS; in board_parse_uart()
317 config->flow_control = FLOW_CONTROL_RTS; in board_parse_uart()
321 config->flow_control = FLOW_CONTROL_CTS_RTS; in board_parse_uart()
328 config->parity = NO_PARITY; in board_parse_uart()
332 config->parity = ODD_PARITY; in board_parse_uart()
336 config->parity = EVEN_PARITY; in board_parse_uart()
379 i2c_device->config.address_width = 7; in board_set_i2c_default()
380 i2c_device->config.freq = 100000; in board_set_i2c_default()
381 i2c_device->config.mode = I2C_MODE_MASTER; in board_set_i2c_default()
382 i2c_device->config.dev_addr = 0xFF; in board_set_i2c_default()
393 i2c_config_t *config = (i2c_config_t *)&device.config; in board_parse_i2c() local
421 config->address_width = I2C_HAL_ADDRESS_WIDTH_7BIT; in board_parse_i2c()
424 config->address_width = I2C_HAL_ADDRESS_WIDTH_10BIT; in board_parse_i2c()
434 config->freq = temp->valueint; in board_parse_i2c()
440 config->mode = I2C_MODE_MASTER; in board_parse_i2c()
444 config->mode = I2C_MODE_SLAVE; in board_parse_i2c()
450 config->dev_addr = temp->valueint; in board_parse_i2c()
492 spi_device->config.data_size = 8; in board_set_spi_default()
493 spi_device->config.mode = 3; in board_set_spi_default()
494 spi_device->config.cs = 0; in board_set_spi_default()
495 spi_device->config.role = 1; in board_set_spi_default()
496 spi_device->config.serial_len = 0; in board_set_spi_default()
497 spi_device->config.firstbit = 0; in board_set_spi_default()
498 spi_device->config.t_mode = 1; in board_set_spi_default()
499 spi_device->config.freq = 2000000; in board_set_spi_default()
510 spi_config_t *config = (spi_config_t *)&device.config; in board_parse_spi() local
536 config->mode = SPI_WORK_MODE_0; in board_parse_spi()
540 config->mode = SPI_WORK_MODE_1; in board_parse_spi()
544 config->mode = SPI_WORK_MODE_2; in board_parse_spi()
548 config->mode = SPI_WORK_MODE_3; in board_parse_spi()
554 config->freq = temp->valueint; in board_parse_spi()
596 can_device->config.baud_rate = CAN_BAUD_500K; in board_set_can_default()
597 can_device->config.ide = CAN_IDE_NORMAL; in board_set_can_default()
598 can_device->config.auto_bus_off = CAN_AUTO_BUS_OFF_ENABLE; in board_set_can_default()
599 can_device->config.auto_retry_transmit = CAN_AUTO_RETRY_TRANSMIT_ENABLE; in board_set_can_default()
610 can_config_t *config = (can_config_t *)&device.config; in board_parse_can() local
638 config->baud_rate = CAN_BAUD_1M; in board_parse_can()
641 config->baud_rate = CAN_BAUD_500K; in board_parse_can()
644 config->baud_rate = CAN_BAUD_250K; in board_parse_can()
647 config->baud_rate = CAN_BAUD_125K; in board_parse_can()
657 config->ide = CAN_IDE_NORMAL; in board_parse_can()
661 config->ide = CAN_IDE_EXTEND; in board_parse_can()
669 config->auto_bus_off = CAN_AUTO_BUS_OFF_DISABLE; in board_parse_can()
673 config->auto_bus_off = CAN_AUTO_BUS_OFF_ENABLE; in board_parse_can()
681 config->auto_retry_transmit = CAN_AUTO_RETRY_TRANSMIT_DISABLE; in board_parse_can()
685 config->auto_retry_transmit = CAN_AUTO_RETRY_TRANSMIT_ENABLE; in board_parse_can()
728 pwm_device->config.freq = 0; in board_set_pwm_default()
729 pwm_device->config.duty_cycle = 100; in board_set_pwm_default()
740 pwm_config_t *config = (pwm_config_t *)&device.config; in board_parse_pwm() local
801 adc_device->config.sampling_cycle = 12000000; in board_set_adc_default()
812 adc_config_t *config = (adc_config_t *)&device.config; in board_parse_adc() local
837 config->sampling_cycle = temp->valueint; in board_parse_adc()
952 timer_device->config.reload_mode = TIMER_RELOAD_MANU; in board_set_timer_default()
953 timer_device->config.period = 1000; in board_set_timer_default()
965 timer_config_t *config = (timer_config_t *)&device.config; in board_parse_timer() local