Lines Matching refs:SCSI
20 2. Supported chips and SCSI features
22 3.1 Optimized SCSI SCRIPTS
46 10.2.6 Check SCSI BUS
47 10.2.7 Suggest a default SCSI id for hosts
54 10.4 SCSI BUS checking boot option
55 11. SCSI problem troubleshooting
67 This driver supports the whole SYM53C8XX family of PCI-SCSI controllers.
68 It also support the subset of LSI53C10XX PCI-SCSI controllers that are based
115 SCSI standard documentations are available at T10 site:
119 Useful SCSI tools written by Eric Youngdale are part of most Linux
127 2. Supported chips and SCSI features
135 - SCSI parity checking
149 |Chip |SDMS BIOS |Wide |SCSI std. | Max. sync | |mismatch |
192 :Control commands: write operations to the proc SCSI file system
204 3.1 Optimized SCSI SCRIPTS
207 All chips except the 810, 815 and 825, support new SCSI SCRIPTS instructions
213 modes. The SCSI SCRIPTS had been entirely rewritten using LOAD/STORE instead
224 SCRIPTS (avoids the phase mismatch interrupt that stops the SCSI processor
252 Some known old SCSI devices do not properly support tagged command queuing.
276 is currently set to 16 by default. This value is suitable for most SCSI
277 disks. With large SCSI disks (>= 2GB, cache >= 512KB, average seek time
300 In some special conditions, some SCSI disk firmwares may return a
301 QUEUE FULL status for a SCSI command. This behaviour is managed by the
307 - Every 200 successfully completed SCSI commands, if allowed by the
327 The driver supports SCSI parity checking and PCI bus master parity
345 the proc SCSI file system. The generic command syntax is the
352 apply to all targets of the SCSI chain (except the controller).
405 nego print information about SCSI negotiations
428 will allow disconnection for all devices on the SCSI bus.
466 if only one has a flaw for some SCSI feature, you can disable the
565 10.2.6 Check SCSI BUS
578 10.2.7 Suggest a default SCSI id for hosts
583 hostid=#x (0 < x < 7) x suggested for hosts SCSI id.
586 If a host SCSI id is available from the NVRAM, the driver will ignore
691 10.4 SCSI BUS checking boot option
694 When this option is set to a non-zero value, the driver checks SCSI lines
695 logic state, 100 micro-seconds after having asserted the SCSI RESET line.
696 The driver just reads SCSI lines and checks all lines read FALSE except RESET.
697 Since SCSI devices shall release the BUS at most 800 nano-seconds after SCSI
698 RESET has been asserted, any signal to TRUE may indicate a SCSI BUS problem.
699 Unfortunately, the following common SCSI BUS problems are not detected:
706 devices, ... may cause a SCSI signal to be wrong when the driver reads it.
708 15. SCSI problem troubleshooting
714 Most SCSI problems are due to a non conformant SCSI bus or too buggy
715 devices. If unfortunately you have SCSI problems, you can check the
718 - SCSI bus cables
719 - terminations at both end of the SCSI chain
729 Now, if your SCSI bus is ok, your system has every chance to work
740 your SCSI bus but often causes problems with buggy devices.
742 hard disks. Good SCSI hard disks with a large cache gain advantage of
762 SCSI ID of the device the controller was talking with at the moment the
781 Field C : SIST io register (SCSI Interrupt Status)
783 Bit 0x08 SGE SCSI GROSS ERROR
785 on the SCSI BUS that prevents the SCSI protocol from functioning
788 Indicates that the device released the SCSI BUS when the chip
790 …indicate the SCSI initiator that an error condition not reportable using the SCSI pro…
791 Bit 0x02 RST SCSI BUS Reset
792 Generally SCSI targets do not reset the SCSI BUS, although any
795 SCSI parity error detected.
798 On a faulty SCSI BUS, any error condition among SGE (0x08), UDC (0x04) and
799 PAR (0x01) may be detected by the chip. If your SCSI system sometimes
800 encounters such error conditions, especially SCSI GROSS ERROR, then a SCSI
807 This register reflects the state of the SCSI control lines the
810 Actual value of control lines on the SCSI BUS.
812 Actual value of data lines on the SCSI BUS.
813 Field G : SXFER SCSI Transfer
823 SCSI standards, chip cores functionnals and internal driver data structures.
862 | * Host SCSI ID | Y | Y |
864 | * SCSI parity checking | Y | Y |
868 |SCSI devices parameters |