Lines Matching refs:serial_out
170 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | in mtk8250_dma_enable()
172 serial_out(up, MTK_UART_DMA_EN, in mtk8250_dma_enable()
175 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); in mtk8250_dma_enable()
176 serial_out(up, MTK_UART_EFR, UART_EFR_ECB); in mtk8250_dma_enable()
177 serial_out(up, UART_LCR, lcr); in mtk8250_dma_enable()
225 serial_out(up, UART_IER, serial_in(up, UART_IER) & (~mask)); in mtk8250_disable_intrs()
230 serial_out(up, UART_IER, serial_in(up, UART_IER) | mask); in mtk8250_enable_intrs()
238 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); in mtk8250_set_flow_ctrl()
239 serial_out(up, MTK_UART_EFR, UART_EFR_ECB); in mtk8250_set_flow_ctrl()
240 serial_out(up, UART_LCR, lcr); in mtk8250_set_flow_ctrl()
245 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); in mtk8250_set_flow_ctrl()
246 serial_out(up, MTK_UART_ESCAPE_EN, 0x00); in mtk8250_set_flow_ctrl()
247 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); in mtk8250_set_flow_ctrl()
248 serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) & in mtk8250_set_flow_ctrl()
250 serial_out(up, UART_LCR, lcr); in mtk8250_set_flow_ctrl()
256 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); in mtk8250_set_flow_ctrl()
257 serial_out(up, MTK_UART_ESCAPE_EN, 0x00); in mtk8250_set_flow_ctrl()
258 serial_out(up, UART_MCR, UART_MCR_RTS); in mtk8250_set_flow_ctrl()
259 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); in mtk8250_set_flow_ctrl()
262 serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC | in mtk8250_set_flow_ctrl()
266 serial_out(up, UART_LCR, lcr); in mtk8250_set_flow_ctrl()
272 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); in mtk8250_set_flow_ctrl()
273 serial_out(up, MTK_UART_ESCAPE_EN, 0x01); in mtk8250_set_flow_ctrl()
274 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); in mtk8250_set_flow_ctrl()
277 serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 | in mtk8250_set_flow_ctrl()
281 serial_out(up, MTK_UART_XON1, START_CHAR(port->state->port.tty)); in mtk8250_set_flow_ctrl()
282 serial_out(up, MTK_UART_XOFF1, STOP_CHAR(port->state->port.tty)); in mtk8250_set_flow_ctrl()
283 serial_out(up, UART_LCR, lcr); in mtk8250_set_flow_ctrl()