Lines Matching refs:default
83 guest operating systems. This is the default.
108 operating systems. This is the default.
228 Legal weights range from 1 to 65535 and the default is 256.
237 The default, 0, means there is no cap.
389 The default for B<on_poweroff> is B<destroy>.
418 (it's supported when using B<qemu-xen> and the default BIOS 'seabios',
481 Boot the guest using the default BIOS firmware, which depends on the
486 Boot the guest using the default UEFI firmware, currently OVMF.
528 This option specifies to use a non-default shim.
573 The default is settable via L<xl.conf(5)>.
579 via the grant mechanism by this domain. The default value is settable via
739 Simple DirectMedia Layer). The default is 0 (not enabled).
755 device-model was compiled with OpenGL support. The default is 0 (disabled).
765 B<qemu(1)> manpage. The default is B<en-us>.
848 By default this isn't set so we don't check all RDMs. Instead, we just check
939 This option is the default.
953 number is 31. The default is 8.
1032 Note: by default B<lspci(1)> will omit the domain (B<DDDD>) if it
1044 By default pciback only allows PV guests to write "known safe" values
1063 function when this option is enabled. Therefore the default is false (0).
1077 D0-D3hot power management states for the PCI device. The default is false (0).
1082 option but just specific to a given device. The default is "relaxed".
1090 Changes the default value of B<permissive> for all PCI devices passed
1095 Changes the default value of B<msitranslate> for all PCI devices passed
1100 Changes the default value of B<seize> for all PCI devices passed
1105 B<(HVM only)> Changes the default value of B<power_mgmt> for all PCI
1157 =item B<1>, B<"default">
1201 The default value is 2048.
1226 by default.
1251 The default of 1023 should be sufficient for typical guests. The
1490 The default is B<cd>, meaning try booting from the hard disk first, but fall
1517 time but may not be supported by default in older operating systems, e.g.
1522 The default is B<ide>.
1543 Use of HAP is the default when available.
1552 when Xen thinks it appropriate, is the default.
1558 state. By default this is 1MB per guest vCPU plus 8KB per MB of guest
1579 By default, a guess is made based on the device model, but sometimes
1586 Loads ROMBIOS, a 16-bit x86 compatible BIOS. This is used by default
1593 Loads SeaBIOS, a 16-bit x86 compatible BIOS. This is used by default
1626 default and usually you should omit it. However, it may be necessary to
1628 This option is true for x86 while it's false for ARM by default.
1633 ACPI table. True (1) by default.
1638 table. True (1) by default.
1643 firmware ACPI table. False (0) by default.
1652 always include these tables. This option is enabled by default and you
1668 option is enabled by default and you should usually omit it.
1680 components within a single guest domain. This option is disabled by default.
1688 Altp2m is disabled for the domain (default).
1711 disabled by default and is available only to HVM domains.
1731 This option is disabled by default.
1745 'x' -> Get a safe value (pass through and mask with the default policy)
1854 =item B<default>
1859 If a HVM container in B<default> TSC mode is created on a host that
1888 determined in a similar way to that of B<default> TSC mode.
1896 Set the real time clock to local time or to UTC. False (0) by default,
1901 Set the real time clock offset in seconds. No offset (0) by default.
1908 frequency (HZ) values. The default is true (1).
1981 Setting B<xen_platform_pci=0> with the default device_model "qemu-xen"
2042 This is a special value that enables the default set of groups, which
2092 When using the qemu-xen-traditional device-model, the default as well as
2094 1600x1200 at 32bpp. For the upstream qemu-xen device-model, the default and
2100 device-model, the default and minimum is 8 MB.
2102 For QXL vga, both the default and minimal are 128MB.
2111 The default is false (0) which means to emulate
2119 The default is B<cirrus>.
2129 other VNC-related settings. The default is (1) enabled.
2159 B<qemu(1)> manpage. The default is B<en-us>.
2164 Simple DirectMedia Layer). The default is (0) not enabled.
2174 Enable or disable the virtual graphics device. The default is to
2213 B<spicepasswd> must be set. The default is (0) false.
2221 Whether SPICE agent is used for client mouse mode. The default is (1) true.
2231 The default is (0) disabled.
2236 B<spicevdagent> is enabled. The default is (0) false.
2243 an USB2.0 controller. The default is (0) disabled.
2248 the QEMU default will be used. Please see the documentation of your QEMU
2256 otherwise the QEMU default will be used.
2279 B<qemu(1)> manpage for details. The default is not to export any sound
2327 The xen-pvdevice should be omitted. This is the default.
2354 This option is disabled by default.
2360 default.
2428 Use of HAP is the default when available.
2437 when Xen thinks it appropriate, is the default.
2443 state. By default this is 1MB per guest vCPU plus 8KB per MB of guest
2473 This device-model is the default for Linux dom0.
2478 This device-model is still the default for NetBSD dom0.
2482 It is recommended to accept the default value for new guests. If
2533 The default is B<en-us>.
2560 =item B<default>
2587 (HVM only) Enable MCA capabilities besides default ones enabled
2597 =item B<default>