1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3  * Freescale 83xx USB SOC setup code
4  *
5  * Copyright (C) 2007 Freescale Semiconductor, Inc.
6  * Author: Li Yang
7  */
8 
9 
10 #include <linux/stddef.h>
11 #include <linux/kernel.h>
12 #include <linux/errno.h>
13 #include <linux/of.h>
14 #include <linux/of_address.h>
15 
16 #include <asm/io.h>
17 #include <sysdev/fsl_soc.h>
18 
19 #include "mpc83xx.h"
20 
21 
22 #ifdef CONFIG_PPC_MPC834x
mpc834x_usb_cfg(void)23 int __init mpc834x_usb_cfg(void)
24 {
25 	unsigned long sccr, sicrl, sicrh;
26 	void __iomem *immap;
27 	struct device_node *np = NULL;
28 	int port0_is_dr = 0, port1_is_dr = 0;
29 	const void *prop, *dr_mode;
30 
31 	immap = ioremap(get_immrbase(), 0x1000);
32 	if (!immap)
33 		return -ENOMEM;
34 
35 	/* Read registers */
36 	/* Note: DR and MPH must use the same clock setting in SCCR */
37 	sccr = in_be32(immap + MPC83XX_SCCR_OFFS) & ~MPC83XX_SCCR_USB_MASK;
38 	sicrl = in_be32(immap + MPC83XX_SICRL_OFFS) & ~MPC834X_SICRL_USB_MASK;
39 	sicrh = in_be32(immap + MPC83XX_SICRH_OFFS) & ~MPC834X_SICRH_USB_UTMI;
40 
41 	np = of_find_compatible_node(NULL, NULL, "fsl-usb2-dr");
42 	if (np) {
43 		sccr |= MPC83XX_SCCR_USB_DRCM_11;  /* 1:3 */
44 
45 		prop = of_get_property(np, "phy_type", NULL);
46 		port1_is_dr = 1;
47 		if (prop && (!strcmp(prop, "utmi") ||
48 					!strcmp(prop, "utmi_wide"))) {
49 			sicrl |= MPC834X_SICRL_USB0 | MPC834X_SICRL_USB1;
50 			sicrh |= MPC834X_SICRH_USB_UTMI;
51 			port0_is_dr = 1;
52 		} else if (prop && !strcmp(prop, "serial")) {
53 			dr_mode = of_get_property(np, "dr_mode", NULL);
54 			if (dr_mode && !strcmp(dr_mode, "otg")) {
55 				sicrl |= MPC834X_SICRL_USB0 | MPC834X_SICRL_USB1;
56 				port0_is_dr = 1;
57 			} else {
58 				sicrl |= MPC834X_SICRL_USB1;
59 			}
60 		} else if (prop && !strcmp(prop, "ulpi")) {
61 			sicrl |= MPC834X_SICRL_USB1;
62 		} else {
63 			printk(KERN_WARNING "834x USB PHY type not supported\n");
64 		}
65 		of_node_put(np);
66 	}
67 	np = of_find_compatible_node(NULL, NULL, "fsl-usb2-mph");
68 	if (np) {
69 		sccr |= MPC83XX_SCCR_USB_MPHCM_11; /* 1:3 */
70 
71 		prop = of_get_property(np, "port0", NULL);
72 		if (prop) {
73 			if (port0_is_dr)
74 				printk(KERN_WARNING
75 					"834x USB port0 can't be used by both DR and MPH!\n");
76 			sicrl &= ~MPC834X_SICRL_USB0;
77 		}
78 		prop = of_get_property(np, "port1", NULL);
79 		if (prop) {
80 			if (port1_is_dr)
81 				printk(KERN_WARNING
82 					"834x USB port1 can't be used by both DR and MPH!\n");
83 			sicrl &= ~MPC834X_SICRL_USB1;
84 		}
85 		of_node_put(np);
86 	}
87 
88 	/* Write back */
89 	out_be32(immap + MPC83XX_SCCR_OFFS, sccr);
90 	out_be32(immap + MPC83XX_SICRL_OFFS, sicrl);
91 	out_be32(immap + MPC83XX_SICRH_OFFS, sicrh);
92 
93 	iounmap(immap);
94 	return 0;
95 }
96 #endif /* CONFIG_PPC_MPC834x */
97 
98 #ifdef CONFIG_PPC_MPC831x
mpc831x_usb_cfg(void)99 int __init mpc831x_usb_cfg(void)
100 {
101 	u32 temp;
102 	void __iomem *immap, *usb_regs;
103 	struct device_node *np = NULL;
104 	struct device_node *immr_node = NULL;
105 	const void *prop;
106 	struct resource res;
107 	int ret = 0;
108 #ifdef CONFIG_USB_OTG
109 	const void *dr_mode;
110 #endif
111 
112 	np = of_find_compatible_node(NULL, NULL, "fsl-usb2-dr");
113 	if (!np)
114 		return -ENODEV;
115 	prop = of_get_property(np, "phy_type", NULL);
116 
117 	/* Map IMMR space for pin and clock settings */
118 	immap = ioremap(get_immrbase(), 0x1000);
119 	if (!immap) {
120 		of_node_put(np);
121 		return -ENOMEM;
122 	}
123 
124 	/* Configure clock */
125 	immr_node = of_get_parent(np);
126 	if (immr_node && (of_device_is_compatible(immr_node, "fsl,mpc8315-immr") ||
127 			of_device_is_compatible(immr_node, "fsl,mpc8308-immr")))
128 		clrsetbits_be32(immap + MPC83XX_SCCR_OFFS,
129 		                MPC8315_SCCR_USB_MASK,
130 		                MPC8315_SCCR_USB_DRCM_01);
131 	else
132 		clrsetbits_be32(immap + MPC83XX_SCCR_OFFS,
133 		                MPC83XX_SCCR_USB_MASK,
134 		                MPC83XX_SCCR_USB_DRCM_11);
135 
136 	/* Configure pin mux for ULPI.  There is no pin mux for UTMI */
137 	if (prop && !strcmp(prop, "ulpi")) {
138 		if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
139 			clrsetbits_be32(immap + MPC83XX_SICRH_OFFS,
140 					MPC8308_SICRH_USB_MASK,
141 					MPC8308_SICRH_USB_ULPI);
142 		} else if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr")) {
143 			clrsetbits_be32(immap + MPC83XX_SICRL_OFFS,
144 					MPC8315_SICRL_USB_MASK,
145 					MPC8315_SICRL_USB_ULPI);
146 			clrsetbits_be32(immap + MPC83XX_SICRH_OFFS,
147 					MPC8315_SICRH_USB_MASK,
148 					MPC8315_SICRH_USB_ULPI);
149 		} else {
150 			clrsetbits_be32(immap + MPC83XX_SICRL_OFFS,
151 					MPC831X_SICRL_USB_MASK,
152 					MPC831X_SICRL_USB_ULPI);
153 			clrsetbits_be32(immap + MPC83XX_SICRH_OFFS,
154 					MPC831X_SICRH_USB_MASK,
155 					MPC831X_SICRH_USB_ULPI);
156 		}
157 	}
158 
159 	iounmap(immap);
160 
161 	of_node_put(immr_node);
162 
163 	/* Map USB SOC space */
164 	ret = of_address_to_resource(np, 0, &res);
165 	if (ret) {
166 		of_node_put(np);
167 		return ret;
168 	}
169 	usb_regs = ioremap(res.start, resource_size(&res));
170 
171 	/* Using on-chip PHY */
172 	if (prop && (!strcmp(prop, "utmi_wide") ||
173 		     !strcmp(prop, "utmi"))) {
174 		u32 refsel;
175 
176 		if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr"))
177 			goto out;
178 
179 		if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
180 			refsel = CONTROL_REFSEL_24MHZ;
181 		else
182 			refsel = CONTROL_REFSEL_48MHZ;
183 		/* Set UTMI_PHY_EN and REFSEL */
184 		out_be32(usb_regs + FSL_USB2_CONTROL_OFFS,
185 				CONTROL_UTMI_PHY_EN | refsel);
186 	/* Using external UPLI PHY */
187 	} else if (prop && !strcmp(prop, "ulpi")) {
188 		/* Set PHY_CLK_SEL to ULPI */
189 		temp = CONTROL_PHY_CLK_SEL_ULPI;
190 #ifdef CONFIG_USB_OTG
191 		/* Set OTG_PORT */
192 		if (!of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
193 			dr_mode = of_get_property(np, "dr_mode", NULL);
194 			if (dr_mode && !strcmp(dr_mode, "otg"))
195 				temp |= CONTROL_OTG_PORT;
196 		}
197 #endif /* CONFIG_USB_OTG */
198 		out_be32(usb_regs + FSL_USB2_CONTROL_OFFS, temp);
199 	} else {
200 		printk(KERN_WARNING "831x USB PHY type not supported\n");
201 		ret = -EINVAL;
202 	}
203 
204 out:
205 	iounmap(usb_regs);
206 	of_node_put(np);
207 	return ret;
208 }
209 #endif /* CONFIG_PPC_MPC831x */
210 
211 #ifdef CONFIG_PPC_MPC837x
mpc837x_usb_cfg(void)212 int __init mpc837x_usb_cfg(void)
213 {
214 	void __iomem *immap;
215 	struct device_node *np = NULL;
216 	const void *prop;
217 	int ret = 0;
218 
219 	np = of_find_compatible_node(NULL, NULL, "fsl-usb2-dr");
220 	if (!np || !of_device_is_available(np)) {
221 		of_node_put(np);
222 		return -ENODEV;
223 	}
224 	prop = of_get_property(np, "phy_type", NULL);
225 
226 	if (!prop || (strcmp(prop, "ulpi") && strcmp(prop, "serial"))) {
227 		printk(KERN_WARNING "837x USB PHY type not supported\n");
228 		of_node_put(np);
229 		return -EINVAL;
230 	}
231 
232 	/* Map IMMR space for pin and clock settings */
233 	immap = ioremap(get_immrbase(), 0x1000);
234 	if (!immap) {
235 		of_node_put(np);
236 		return -ENOMEM;
237 	}
238 
239 	/* Configure clock */
240 	clrsetbits_be32(immap + MPC83XX_SCCR_OFFS, MPC837X_SCCR_USB_DRCM_11,
241 			MPC837X_SCCR_USB_DRCM_11);
242 
243 	/* Configure pin mux for ULPI/serial */
244 	clrsetbits_be32(immap + MPC83XX_SICRL_OFFS, MPC837X_SICRL_USB_MASK,
245 			MPC837X_SICRL_USB_ULPI);
246 
247 	iounmap(immap);
248 	of_node_put(np);
249 	return ret;
250 }
251 #endif /* CONFIG_PPC_MPC837x */
252