1 // SPDX-License-Identifier: GPL-2.0+
2 /* Microchip Sparx5 Switch driver
3  *
4  * Copyright (c) 2021 Microchip Technology Inc. and its subsidiaries.
5  */
6 
7 #include <linux/module.h>
8 #include <linux/phy/phy.h>
9 #include <net/dcbnl.h>
10 
11 #include "sparx5_main_regs.h"
12 #include "sparx5_main.h"
13 #include "sparx5_port.h"
14 
15 #define SPX5_ETYPE_TAG_C     0x8100
16 #define SPX5_ETYPE_TAG_S     0x88a8
17 
18 #define SPX5_WAIT_US         1000
19 #define SPX5_WAIT_MAX_US     2000
20 
21 enum port_error {
22 	SPX5_PERR_SPEED,
23 	SPX5_PERR_IFTYPE,
24 };
25 
26 #define PAUSE_DISCARD        0xC
27 #define ETH_MAXLEN           (ETH_DATA_LEN + ETH_HLEN + ETH_FCS_LEN)
28 
decode_sgmii_word(u16 lp_abil,struct sparx5_port_status * status)29 static void decode_sgmii_word(u16 lp_abil, struct sparx5_port_status *status)
30 {
31 	status->an_complete = true;
32 	if (!(lp_abil & LPA_SGMII_LINK)) {
33 		status->link = false;
34 		return;
35 	}
36 
37 	switch (lp_abil & LPA_SGMII_SPD_MASK) {
38 	case LPA_SGMII_10:
39 		status->speed = SPEED_10;
40 		break;
41 	case LPA_SGMII_100:
42 		status->speed = SPEED_100;
43 		break;
44 	case LPA_SGMII_1000:
45 		status->speed = SPEED_1000;
46 		break;
47 	default:
48 		status->link = false;
49 		return;
50 	}
51 	if (lp_abil & LPA_SGMII_FULL_DUPLEX)
52 		status->duplex = DUPLEX_FULL;
53 	else
54 		status->duplex = DUPLEX_HALF;
55 }
56 
decode_cl37_word(u16 lp_abil,uint16_t ld_abil,struct sparx5_port_status * status)57 static void decode_cl37_word(u16 lp_abil, uint16_t ld_abil, struct sparx5_port_status *status)
58 {
59 	status->link = !(lp_abil & ADVERTISE_RFAULT) && status->link;
60 	status->an_complete = true;
61 	status->duplex = (ADVERTISE_1000XFULL & lp_abil) ?
62 		DUPLEX_FULL : DUPLEX_UNKNOWN; // 1G HDX not supported
63 
64 	if ((ld_abil & ADVERTISE_1000XPAUSE) &&
65 	    (lp_abil & ADVERTISE_1000XPAUSE)) {
66 		status->pause = MLO_PAUSE_RX | MLO_PAUSE_TX;
67 	} else if ((ld_abil & ADVERTISE_1000XPSE_ASYM) &&
68 		   (lp_abil & ADVERTISE_1000XPSE_ASYM)) {
69 		status->pause |= (lp_abil & ADVERTISE_1000XPAUSE) ?
70 			MLO_PAUSE_TX : 0;
71 		status->pause |= (ld_abil & ADVERTISE_1000XPAUSE) ?
72 			MLO_PAUSE_RX : 0;
73 	} else {
74 		status->pause = MLO_PAUSE_NONE;
75 	}
76 }
77 
sparx5_get_dev2g5_status(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_status * status)78 static int sparx5_get_dev2g5_status(struct sparx5 *sparx5,
79 				    struct sparx5_port *port,
80 				    struct sparx5_port_status *status)
81 {
82 	u32 portno = port->portno;
83 	u16 lp_adv, ld_adv;
84 	u32 value;
85 
86 	/* Get PCS Link down sticky */
87 	value = spx5_rd(sparx5, DEV2G5_PCS1G_STICKY(portno));
88 	status->link_down = DEV2G5_PCS1G_STICKY_LINK_DOWN_STICKY_GET(value);
89 	if (status->link_down)	/* Clear the sticky */
90 		spx5_wr(value, sparx5, DEV2G5_PCS1G_STICKY(portno));
91 
92 	/* Get both current Link and Sync status */
93 	value = spx5_rd(sparx5, DEV2G5_PCS1G_LINK_STATUS(portno));
94 	status->link = DEV2G5_PCS1G_LINK_STATUS_LINK_STATUS_GET(value) &&
95 		       DEV2G5_PCS1G_LINK_STATUS_SYNC_STATUS_GET(value);
96 
97 	if (port->conf.portmode == PHY_INTERFACE_MODE_1000BASEX)
98 		status->speed = SPEED_1000;
99 	else if (port->conf.portmode == PHY_INTERFACE_MODE_2500BASEX)
100 		status->speed = SPEED_2500;
101 
102 	status->duplex = DUPLEX_FULL;
103 
104 	/* Get PCS ANEG status register */
105 	value = spx5_rd(sparx5, DEV2G5_PCS1G_ANEG_STATUS(portno));
106 
107 	/* Aneg complete provides more information  */
108 	if (DEV2G5_PCS1G_ANEG_STATUS_ANEG_COMPLETE_GET(value)) {
109 		lp_adv = DEV2G5_PCS1G_ANEG_STATUS_LP_ADV_ABILITY_GET(value);
110 		if (port->conf.portmode == PHY_INTERFACE_MODE_SGMII) {
111 			decode_sgmii_word(lp_adv, status);
112 		} else {
113 			value = spx5_rd(sparx5, DEV2G5_PCS1G_ANEG_CFG(portno));
114 			ld_adv = DEV2G5_PCS1G_ANEG_CFG_ADV_ABILITY_GET(value);
115 			decode_cl37_word(lp_adv, ld_adv, status);
116 		}
117 	}
118 	return 0;
119 }
120 
sparx5_get_sfi_status(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_status * status)121 static int sparx5_get_sfi_status(struct sparx5 *sparx5,
122 				 struct sparx5_port *port,
123 				 struct sparx5_port_status *status)
124 {
125 	bool high_speed_dev = sparx5_is_baser(port->conf.portmode);
126 	u32 portno = port->portno;
127 	u32 value, dev, tinst;
128 	void __iomem *inst;
129 
130 	if (!high_speed_dev) {
131 		netdev_err(port->ndev, "error: low speed and SFI mode\n");
132 		return -EINVAL;
133 	}
134 
135 	dev = sparx5_to_high_dev(portno);
136 	tinst = sparx5_port_dev_index(portno);
137 	inst = spx5_inst_get(sparx5, dev, tinst);
138 
139 	value = spx5_inst_rd(inst, DEV10G_MAC_TX_MONITOR_STICKY(0));
140 	if (value != DEV10G_MAC_TX_MONITOR_STICKY_IDLE_STATE_STICKY) {
141 		/* The link is or has been down. Clear the sticky bit */
142 		status->link_down = 1;
143 		spx5_inst_wr(0xffffffff, inst, DEV10G_MAC_TX_MONITOR_STICKY(0));
144 		value = spx5_inst_rd(inst, DEV10G_MAC_TX_MONITOR_STICKY(0));
145 	}
146 	status->link = (value == DEV10G_MAC_TX_MONITOR_STICKY_IDLE_STATE_STICKY);
147 	status->duplex = DUPLEX_FULL;
148 	if (port->conf.portmode == PHY_INTERFACE_MODE_5GBASER)
149 		status->speed = SPEED_5000;
150 	else if (port->conf.portmode == PHY_INTERFACE_MODE_10GBASER)
151 		status->speed = SPEED_10000;
152 	else
153 		status->speed = SPEED_25000;
154 
155 	return 0;
156 }
157 
158 /* Get link status of 1000Base-X/in-band and SFI ports.
159  */
sparx5_get_port_status(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_status * status)160 int sparx5_get_port_status(struct sparx5 *sparx5,
161 			   struct sparx5_port *port,
162 			   struct sparx5_port_status *status)
163 {
164 	memset(status, 0, sizeof(*status));
165 	status->speed = port->conf.speed;
166 	if (port->conf.power_down) {
167 		status->link = false;
168 		return 0;
169 	}
170 	switch (port->conf.portmode) {
171 	case PHY_INTERFACE_MODE_SGMII:
172 	case PHY_INTERFACE_MODE_QSGMII:
173 	case PHY_INTERFACE_MODE_1000BASEX:
174 	case PHY_INTERFACE_MODE_2500BASEX:
175 		return sparx5_get_dev2g5_status(sparx5, port, status);
176 	case PHY_INTERFACE_MODE_5GBASER:
177 	case PHY_INTERFACE_MODE_10GBASER:
178 	case PHY_INTERFACE_MODE_25GBASER:
179 		return sparx5_get_sfi_status(sparx5, port, status);
180 	case PHY_INTERFACE_MODE_NA:
181 		return 0;
182 	default:
183 		netdev_err(port->ndev, "Status not supported");
184 		return -ENODEV;
185 	}
186 	return 0;
187 }
188 
sparx5_port_error(struct sparx5_port * port,struct sparx5_port_config * conf,enum port_error errtype)189 static int sparx5_port_error(struct sparx5_port *port,
190 			     struct sparx5_port_config *conf,
191 			     enum port_error errtype)
192 {
193 	switch (errtype) {
194 	case SPX5_PERR_SPEED:
195 		netdev_err(port->ndev,
196 			   "Interface does not support speed: %u: for %s\n",
197 			   conf->speed, phy_modes(conf->portmode));
198 		break;
199 	case SPX5_PERR_IFTYPE:
200 		netdev_err(port->ndev,
201 			   "Switch port does not support interface type: %s\n",
202 			   phy_modes(conf->portmode));
203 		break;
204 	default:
205 		netdev_err(port->ndev,
206 			   "Interface configuration error\n");
207 	}
208 
209 	return -EINVAL;
210 }
211 
sparx5_port_verify_speed(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)212 static int sparx5_port_verify_speed(struct sparx5 *sparx5,
213 				    struct sparx5_port *port,
214 				    struct sparx5_port_config *conf)
215 {
216 	if ((sparx5_port_is_2g5(port->portno) &&
217 	     conf->speed > SPEED_2500) ||
218 	    (sparx5_port_is_5g(port->portno)  &&
219 	     conf->speed > SPEED_5000) ||
220 	    (sparx5_port_is_10g(port->portno) &&
221 	     conf->speed > SPEED_10000))
222 		return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
223 
224 	switch (conf->portmode) {
225 	case PHY_INTERFACE_MODE_NA:
226 		return -EINVAL;
227 	case PHY_INTERFACE_MODE_1000BASEX:
228 		if (conf->speed != SPEED_1000 ||
229 		    sparx5_port_is_2g5(port->portno))
230 			return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
231 		if (sparx5_port_is_2g5(port->portno))
232 			return sparx5_port_error(port, conf, SPX5_PERR_IFTYPE);
233 		break;
234 	case PHY_INTERFACE_MODE_2500BASEX:
235 		if (conf->speed != SPEED_2500 ||
236 		    sparx5_port_is_2g5(port->portno))
237 			return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
238 		break;
239 	case PHY_INTERFACE_MODE_QSGMII:
240 		if (port->portno > 47)
241 			return sparx5_port_error(port, conf, SPX5_PERR_IFTYPE);
242 		fallthrough;
243 	case PHY_INTERFACE_MODE_SGMII:
244 		if (conf->speed != SPEED_1000 &&
245 		    conf->speed != SPEED_100 &&
246 		    conf->speed != SPEED_10 &&
247 		    conf->speed != SPEED_2500)
248 			return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
249 		break;
250 	case PHY_INTERFACE_MODE_5GBASER:
251 	case PHY_INTERFACE_MODE_10GBASER:
252 	case PHY_INTERFACE_MODE_25GBASER:
253 		if ((conf->speed != SPEED_5000 &&
254 		     conf->speed != SPEED_10000 &&
255 		     conf->speed != SPEED_25000))
256 			return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
257 		break;
258 	default:
259 		return sparx5_port_error(port, conf, SPX5_PERR_IFTYPE);
260 	}
261 	return 0;
262 }
263 
sparx5_dev_change(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)264 static bool sparx5_dev_change(struct sparx5 *sparx5,
265 			      struct sparx5_port *port,
266 			      struct sparx5_port_config *conf)
267 {
268 	return sparx5_is_baser(port->conf.portmode) ^
269 		sparx5_is_baser(conf->portmode);
270 }
271 
sparx5_port_flush_poll(struct sparx5 * sparx5,u32 portno)272 static int sparx5_port_flush_poll(struct sparx5 *sparx5, u32 portno)
273 {
274 	u32  value, resource, prio, delay_cnt = 0;
275 	bool poll_src = true;
276 	char *mem = "";
277 
278 	/* Resource == 0: Memory tracked per source (SRC-MEM)
279 	 * Resource == 1: Frame references tracked per source (SRC-REF)
280 	 * Resource == 2: Memory tracked per destination (DST-MEM)
281 	 * Resource == 3: Frame references tracked per destination. (DST-REF)
282 	 */
283 	while (1) {
284 		bool empty = true;
285 
286 		for (resource = 0; resource < (poll_src ? 2 : 1); resource++) {
287 			u32 base;
288 
289 			base = (resource == 0 ? 2048 : 0) + SPX5_PRIOS * portno;
290 			for (prio = 0; prio < SPX5_PRIOS; prio++) {
291 				value = spx5_rd(sparx5,
292 						QRES_RES_STAT(base + prio));
293 				if (value) {
294 					mem = resource == 0 ?
295 						"DST-MEM" : "SRC-MEM";
296 					empty = false;
297 				}
298 			}
299 		}
300 
301 		if (empty)
302 			break;
303 
304 		if (delay_cnt++ == 2000) {
305 			dev_err(sparx5->dev,
306 				"Flush timeout port %u. %s queue not empty\n",
307 				portno, mem);
308 			return -EINVAL;
309 		}
310 
311 		usleep_range(SPX5_WAIT_US, SPX5_WAIT_MAX_US);
312 	}
313 	return 0;
314 }
315 
sparx5_port_disable(struct sparx5 * sparx5,struct sparx5_port * port,bool high_spd_dev)316 static int sparx5_port_disable(struct sparx5 *sparx5, struct sparx5_port *port, bool high_spd_dev)
317 {
318 	u32 tinst = high_spd_dev ?
319 		    sparx5_port_dev_index(port->portno) : port->portno;
320 	u32 dev = high_spd_dev ?
321 		  sparx5_to_high_dev(port->portno) : TARGET_DEV2G5;
322 	void __iomem *devinst = spx5_inst_get(sparx5, dev, tinst);
323 	u32 spd = port->conf.speed;
324 	u32 spd_prm;
325 	int err;
326 
327 	if (high_spd_dev) {
328 		/* 1: Reset the PCS Rx clock domain  */
329 		spx5_inst_rmw(DEV10G_DEV_RST_CTRL_PCS_RX_RST,
330 			      DEV10G_DEV_RST_CTRL_PCS_RX_RST,
331 			      devinst,
332 			      DEV10G_DEV_RST_CTRL(0));
333 
334 		/* 2: Disable MAC frame reception */
335 		spx5_inst_rmw(0,
336 			      DEV10G_MAC_ENA_CFG_RX_ENA,
337 			      devinst,
338 			      DEV10G_MAC_ENA_CFG(0));
339 	} else {
340 		/* 1: Reset the PCS Rx clock domain  */
341 		spx5_inst_rmw(DEV2G5_DEV_RST_CTRL_PCS_RX_RST,
342 			      DEV2G5_DEV_RST_CTRL_PCS_RX_RST,
343 			      devinst,
344 			      DEV2G5_DEV_RST_CTRL(0));
345 		/* 2: Disable MAC frame reception */
346 		spx5_inst_rmw(0,
347 			      DEV2G5_MAC_ENA_CFG_RX_ENA,
348 			      devinst,
349 			      DEV2G5_MAC_ENA_CFG(0));
350 	}
351 	/* 3: Disable traffic being sent to or from switch port->portno */
352 	spx5_rmw(0,
353 		 QFWD_SWITCH_PORT_MODE_PORT_ENA,
354 		 sparx5,
355 		 QFWD_SWITCH_PORT_MODE(port->portno));
356 
357 	/* 4: Disable dequeuing from the egress queues  */
358 	spx5_rmw(HSCH_PORT_MODE_DEQUEUE_DIS,
359 		 HSCH_PORT_MODE_DEQUEUE_DIS,
360 		 sparx5,
361 		 HSCH_PORT_MODE(port->portno));
362 
363 	/* 5: Disable Flowcontrol */
364 	spx5_rmw(QSYS_PAUSE_CFG_PAUSE_STOP_SET(0xFFF - 1),
365 		 QSYS_PAUSE_CFG_PAUSE_STOP,
366 		 sparx5,
367 		 QSYS_PAUSE_CFG(port->portno));
368 
369 	spd_prm = spd == SPEED_10 ? 1000 : spd == SPEED_100 ? 100 : 10;
370 	/* 6: Wait while the last frame is exiting the queues */
371 	usleep_range(8 * spd_prm, 10 * spd_prm);
372 
373 	/* 7: Flush the queues accociated with the port->portno */
374 	spx5_rmw(HSCH_FLUSH_CTRL_FLUSH_PORT_SET(port->portno) |
375 		 HSCH_FLUSH_CTRL_FLUSH_DST_SET(1) |
376 		 HSCH_FLUSH_CTRL_FLUSH_SRC_SET(1) |
377 		 HSCH_FLUSH_CTRL_FLUSH_ENA_SET(1),
378 		 HSCH_FLUSH_CTRL_FLUSH_PORT |
379 		 HSCH_FLUSH_CTRL_FLUSH_DST |
380 		 HSCH_FLUSH_CTRL_FLUSH_SRC |
381 		 HSCH_FLUSH_CTRL_FLUSH_ENA,
382 		 sparx5,
383 		 HSCH_FLUSH_CTRL);
384 
385 	/* 8: Enable dequeuing from the egress queues */
386 	spx5_rmw(0,
387 		 HSCH_PORT_MODE_DEQUEUE_DIS,
388 		 sparx5,
389 		 HSCH_PORT_MODE(port->portno));
390 
391 	/* 9: Wait until flushing is complete */
392 	err = sparx5_port_flush_poll(sparx5, port->portno);
393 	if (err)
394 		return err;
395 
396 	/* 10: Reset the  MAC clock domain */
397 	if (high_spd_dev) {
398 		spx5_inst_rmw(DEV10G_DEV_RST_CTRL_PCS_TX_RST_SET(1) |
399 			      DEV10G_DEV_RST_CTRL_MAC_RX_RST_SET(1) |
400 			      DEV10G_DEV_RST_CTRL_MAC_TX_RST_SET(1),
401 			      DEV10G_DEV_RST_CTRL_PCS_TX_RST |
402 			      DEV10G_DEV_RST_CTRL_MAC_RX_RST |
403 			      DEV10G_DEV_RST_CTRL_MAC_TX_RST,
404 			      devinst,
405 			      DEV10G_DEV_RST_CTRL(0));
406 
407 	} else {
408 		spx5_inst_rmw(DEV2G5_DEV_RST_CTRL_SPEED_SEL_SET(3) |
409 			      DEV2G5_DEV_RST_CTRL_PCS_TX_RST_SET(1) |
410 			      DEV2G5_DEV_RST_CTRL_PCS_RX_RST_SET(1) |
411 			      DEV2G5_DEV_RST_CTRL_MAC_TX_RST_SET(1) |
412 			      DEV2G5_DEV_RST_CTRL_MAC_RX_RST_SET(1),
413 			      DEV2G5_DEV_RST_CTRL_SPEED_SEL |
414 			      DEV2G5_DEV_RST_CTRL_PCS_TX_RST |
415 			      DEV2G5_DEV_RST_CTRL_PCS_RX_RST |
416 			      DEV2G5_DEV_RST_CTRL_MAC_TX_RST |
417 			      DEV2G5_DEV_RST_CTRL_MAC_RX_RST,
418 			      devinst,
419 			      DEV2G5_DEV_RST_CTRL(0));
420 	}
421 	/* 11: Clear flushing */
422 	spx5_rmw(HSCH_FLUSH_CTRL_FLUSH_PORT_SET(port->portno) |
423 		 HSCH_FLUSH_CTRL_FLUSH_ENA_SET(0),
424 		 HSCH_FLUSH_CTRL_FLUSH_PORT |
425 		 HSCH_FLUSH_CTRL_FLUSH_ENA,
426 		 sparx5,
427 		 HSCH_FLUSH_CTRL);
428 
429 	if (high_spd_dev) {
430 		u32 pcs = sparx5_to_pcs_dev(port->portno);
431 		void __iomem *pcsinst = spx5_inst_get(sparx5, pcs, tinst);
432 
433 		/* 12: Disable 5G/10G/25 BaseR PCS */
434 		spx5_inst_rmw(PCS10G_BR_PCS_CFG_PCS_ENA_SET(0),
435 			      PCS10G_BR_PCS_CFG_PCS_ENA,
436 			      pcsinst,
437 			      PCS10G_BR_PCS_CFG(0));
438 
439 		if (sparx5_port_is_25g(port->portno))
440 			/* Disable 25G PCS */
441 			spx5_rmw(DEV25G_PCS25G_CFG_PCS25G_ENA_SET(0),
442 				 DEV25G_PCS25G_CFG_PCS25G_ENA,
443 				 sparx5,
444 				 DEV25G_PCS25G_CFG(tinst));
445 	} else {
446 		/* 12: Disable 1G PCS */
447 		spx5_rmw(DEV2G5_PCS1G_CFG_PCS_ENA_SET(0),
448 			 DEV2G5_PCS1G_CFG_PCS_ENA,
449 			 sparx5,
450 			 DEV2G5_PCS1G_CFG(port->portno));
451 	}
452 
453 	/* The port is now flushed and disabled  */
454 	return 0;
455 }
456 
sparx5_port_fifo_sz(struct sparx5 * sparx5,u32 portno,u32 speed)457 static int sparx5_port_fifo_sz(struct sparx5 *sparx5,
458 			       u32 portno, u32 speed)
459 {
460 	u32 sys_clk = sparx5_clk_period(sparx5->coreclock);
461 	const u32 taxi_dist[SPX5_PORTS_ALL] = {
462 		6, 8, 10, 6, 8, 10, 6, 8, 10, 6, 8, 10,
463 		4, 4, 4, 4,
464 		11, 12, 13, 14, 15, 16, 17, 18,
465 		11, 12, 13, 14, 15, 16, 17, 18,
466 		11, 12, 13, 14, 15, 16, 17, 18,
467 		11, 12, 13, 14, 15, 16, 17, 18,
468 		4, 6, 8, 4, 6, 8, 6, 8,
469 		2, 2, 2, 2, 2, 2, 2, 4, 2
470 	};
471 	u32 mac_per    = 6400, tmp1, tmp2, tmp3;
472 	u32 fifo_width = 16;
473 	u32 mac_width  = 8;
474 	u32 addition   = 0;
475 
476 	switch (speed) {
477 	case SPEED_25000:
478 		return 0;
479 	case SPEED_10000:
480 		mac_per = 6400;
481 		mac_width = 8;
482 		addition = 1;
483 		break;
484 	case SPEED_5000:
485 		mac_per = 12800;
486 		mac_width = 8;
487 		addition = 0;
488 		break;
489 	case SPEED_2500:
490 		mac_per = 3200;
491 		mac_width = 1;
492 		addition = 0;
493 		break;
494 	case SPEED_1000:
495 		mac_per =  8000;
496 		mac_width = 1;
497 		addition = 0;
498 		break;
499 	case SPEED_100:
500 	case SPEED_10:
501 		return 1;
502 	default:
503 		break;
504 	}
505 
506 	tmp1 = 1000 * mac_width / fifo_width;
507 	tmp2 = 3000 + ((12000 + 2 * taxi_dist[portno] * 1000)
508 		       * sys_clk / mac_per);
509 	tmp3 = tmp1 * tmp2 / 1000;
510 	return  (tmp3 + 2000 + 999) / 1000 + addition;
511 }
512 
513 /* Configure port muxing:
514  * QSGMII:     4x2G5 devices
515  */
sparx5_port_mux_set(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)516 static int sparx5_port_mux_set(struct sparx5 *sparx5,
517 			       struct sparx5_port *port,
518 			       struct sparx5_port_config *conf)
519 {
520 	u32 portno = port->portno;
521 	u32 inst;
522 
523 	if (port->conf.portmode == conf->portmode)
524 		return 0; /* Nothing to do */
525 
526 	switch (conf->portmode) {
527 	case PHY_INTERFACE_MODE_QSGMII: /* QSGMII: 4x2G5 devices. Mode Q'  */
528 		inst = (portno - portno % 4) / 4;
529 		spx5_rmw(BIT(inst),
530 			 BIT(inst),
531 			 sparx5,
532 			 PORT_CONF_QSGMII_ENA);
533 
534 		if ((portno / 4 % 2) == 0) {
535 			/* Affects d0-d3,d8-d11..d40-d43 */
536 			spx5_rmw(PORT_CONF_USGMII_CFG_BYPASS_SCRAM_SET(1) |
537 				 PORT_CONF_USGMII_CFG_BYPASS_DESCRAM_SET(1) |
538 				 PORT_CONF_USGMII_CFG_QUAD_MODE_SET(1),
539 				 PORT_CONF_USGMII_CFG_BYPASS_SCRAM |
540 				 PORT_CONF_USGMII_CFG_BYPASS_DESCRAM |
541 				 PORT_CONF_USGMII_CFG_QUAD_MODE,
542 				 sparx5,
543 				 PORT_CONF_USGMII_CFG((portno / 8)));
544 		}
545 		break;
546 	default:
547 		break;
548 	}
549 	return 0;
550 }
551 
sparx5_port_max_tags_set(struct sparx5 * sparx5,struct sparx5_port * port)552 static int sparx5_port_max_tags_set(struct sparx5 *sparx5,
553 				    struct sparx5_port *port)
554 {
555 	enum sparx5_port_max_tags max_tags    = port->max_vlan_tags;
556 	int tag_ct          = max_tags == SPX5_PORT_MAX_TAGS_ONE ? 1 :
557 			      max_tags == SPX5_PORT_MAX_TAGS_TWO ? 2 : 0;
558 	bool dtag           = max_tags == SPX5_PORT_MAX_TAGS_TWO;
559 	enum sparx5_vlan_port_type vlan_type  = port->vlan_type;
560 	bool dotag          = max_tags != SPX5_PORT_MAX_TAGS_NONE;
561 	u32 dev             = sparx5_to_high_dev(port->portno);
562 	u32 tinst           = sparx5_port_dev_index(port->portno);
563 	void __iomem *inst  = spx5_inst_get(sparx5, dev, tinst);
564 	u32 etype;
565 
566 	etype = (vlan_type == SPX5_VLAN_PORT_TYPE_S_CUSTOM ?
567 		 port->custom_etype :
568 		 vlan_type == SPX5_VLAN_PORT_TYPE_C ?
569 		 SPX5_ETYPE_TAG_C : SPX5_ETYPE_TAG_S);
570 
571 	spx5_wr(DEV2G5_MAC_TAGS_CFG_TAG_ID_SET(etype) |
572 		DEV2G5_MAC_TAGS_CFG_PB_ENA_SET(dtag) |
573 		DEV2G5_MAC_TAGS_CFG_VLAN_AWR_ENA_SET(dotag) |
574 		DEV2G5_MAC_TAGS_CFG_VLAN_LEN_AWR_ENA_SET(dotag),
575 		sparx5,
576 		DEV2G5_MAC_TAGS_CFG(port->portno));
577 
578 	if (sparx5_port_is_2g5(port->portno))
579 		return 0;
580 
581 	spx5_inst_rmw(DEV10G_MAC_TAGS_CFG_TAG_ID_SET(etype) |
582 		      DEV10G_MAC_TAGS_CFG_TAG_ENA_SET(dotag),
583 		      DEV10G_MAC_TAGS_CFG_TAG_ID |
584 		      DEV10G_MAC_TAGS_CFG_TAG_ENA,
585 		      inst,
586 		      DEV10G_MAC_TAGS_CFG(0, 0));
587 
588 	spx5_inst_rmw(DEV10G_MAC_NUM_TAGS_CFG_NUM_TAGS_SET(tag_ct),
589 		      DEV10G_MAC_NUM_TAGS_CFG_NUM_TAGS,
590 		      inst,
591 		      DEV10G_MAC_NUM_TAGS_CFG(0));
592 
593 	spx5_inst_rmw(DEV10G_MAC_MAXLEN_CFG_MAX_LEN_TAG_CHK_SET(dotag),
594 		      DEV10G_MAC_MAXLEN_CFG_MAX_LEN_TAG_CHK,
595 		      inst,
596 		      DEV10G_MAC_MAXLEN_CFG(0));
597 	return 0;
598 }
599 
sparx5_port_fwd_urg(struct sparx5 * sparx5,u32 speed)600 int sparx5_port_fwd_urg(struct sparx5 *sparx5, u32 speed)
601 {
602 	u32 clk_period_ps = 1600; /* 625Mhz for now */
603 	u32 urg = 672000;
604 
605 	switch (speed) {
606 	case SPEED_10:
607 	case SPEED_100:
608 	case SPEED_1000:
609 		urg = 672000;
610 		break;
611 	case SPEED_2500:
612 		urg = 270000;
613 		break;
614 	case SPEED_5000:
615 		urg = 135000;
616 		break;
617 	case SPEED_10000:
618 		urg = 67200;
619 		break;
620 	case SPEED_25000:
621 		urg = 27000;
622 		break;
623 	}
624 	return urg / clk_period_ps - 1;
625 }
626 
sparx5_wm_enc(u16 value)627 static u16 sparx5_wm_enc(u16 value)
628 {
629 	if (value >= 2048)
630 		return 2048 + value / 16;
631 
632 	return value;
633 }
634 
sparx5_port_fc_setup(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)635 static int sparx5_port_fc_setup(struct sparx5 *sparx5,
636 				struct sparx5_port *port,
637 				struct sparx5_port_config *conf)
638 {
639 	bool fc_obey = conf->pause & MLO_PAUSE_RX ? 1 : 0;
640 	u32 pause_stop = 0xFFF - 1; /* FC gen disabled */
641 
642 	if (conf->pause & MLO_PAUSE_TX)
643 		pause_stop = sparx5_wm_enc(4  * (ETH_MAXLEN /
644 						 SPX5_BUFFER_CELL_SZ));
645 
646 	/* Set HDX flowcontrol */
647 	spx5_rmw(DSM_MAC_CFG_HDX_BACKPREASSURE_SET(conf->duplex == DUPLEX_HALF),
648 		 DSM_MAC_CFG_HDX_BACKPREASSURE,
649 		 sparx5,
650 		 DSM_MAC_CFG(port->portno));
651 
652 	/* Obey flowcontrol  */
653 	spx5_rmw(DSM_RX_PAUSE_CFG_RX_PAUSE_EN_SET(fc_obey),
654 		 DSM_RX_PAUSE_CFG_RX_PAUSE_EN,
655 		 sparx5,
656 		 DSM_RX_PAUSE_CFG(port->portno));
657 
658 	/* Disable forward pressure */
659 	spx5_rmw(QSYS_FWD_PRESSURE_FWD_PRESSURE_DIS_SET(fc_obey),
660 		 QSYS_FWD_PRESSURE_FWD_PRESSURE_DIS,
661 		 sparx5,
662 		 QSYS_FWD_PRESSURE(port->portno));
663 
664 	/* Generate pause frames */
665 	spx5_rmw(QSYS_PAUSE_CFG_PAUSE_STOP_SET(pause_stop),
666 		 QSYS_PAUSE_CFG_PAUSE_STOP,
667 		 sparx5,
668 		 QSYS_PAUSE_CFG(port->portno));
669 
670 	return 0;
671 }
672 
sparx5_get_aneg_word(struct sparx5_port_config * conf)673 static u16 sparx5_get_aneg_word(struct sparx5_port_config *conf)
674 {
675 	if (conf->portmode == PHY_INTERFACE_MODE_1000BASEX) /* cl-37 aneg */
676 		return (conf->pause_adv | ADVERTISE_LPACK | ADVERTISE_1000XFULL);
677 	else
678 		return 1; /* Enable SGMII Aneg */
679 }
680 
sparx5_serdes_set(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)681 int sparx5_serdes_set(struct sparx5 *sparx5,
682 		      struct sparx5_port *port,
683 		      struct sparx5_port_config *conf)
684 {
685 	int portmode, err, speed = conf->speed;
686 
687 	if (conf->portmode == PHY_INTERFACE_MODE_QSGMII &&
688 	    ((port->portno % 4) != 0)) {
689 		return 0;
690 	}
691 	if (sparx5_is_baser(conf->portmode)) {
692 		if (conf->portmode == PHY_INTERFACE_MODE_25GBASER)
693 			speed = SPEED_25000;
694 		else if (conf->portmode == PHY_INTERFACE_MODE_10GBASER)
695 			speed = SPEED_10000;
696 		else
697 			speed = SPEED_5000;
698 	}
699 
700 	err = phy_set_media(port->serdes, conf->media);
701 	if (err)
702 		return err;
703 	if (speed > 0) {
704 		err = phy_set_speed(port->serdes, speed);
705 		if (err)
706 			return err;
707 	}
708 	if (conf->serdes_reset) {
709 		err = phy_reset(port->serdes);
710 		if (err)
711 			return err;
712 	}
713 
714 	/* Configure SerDes with port parameters
715 	 * For BaseR, the serdes driver supports 10GGBASE-R and speed 5G/10G/25G
716 	 */
717 	portmode = conf->portmode;
718 	if (sparx5_is_baser(conf->portmode))
719 		portmode = PHY_INTERFACE_MODE_10GBASER;
720 	err = phy_set_mode_ext(port->serdes, PHY_MODE_ETHERNET, portmode);
721 	if (err)
722 		return err;
723 	conf->serdes_reset = false;
724 	return err;
725 }
726 
sparx5_port_pcs_low_set(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)727 static int sparx5_port_pcs_low_set(struct sparx5 *sparx5,
728 				   struct sparx5_port *port,
729 				   struct sparx5_port_config *conf)
730 {
731 	bool sgmii = false, inband_aneg = false;
732 	int err;
733 
734 	if (port->conf.inband) {
735 		if (conf->portmode == PHY_INTERFACE_MODE_SGMII ||
736 		    conf->portmode == PHY_INTERFACE_MODE_QSGMII)
737 			inband_aneg = true; /* Cisco-SGMII in-band-aneg */
738 		else if (conf->portmode == PHY_INTERFACE_MODE_1000BASEX &&
739 			 conf->autoneg)
740 			inband_aneg = true; /* Clause-37 in-band-aneg */
741 
742 		err = sparx5_serdes_set(sparx5, port, conf);
743 		if (err)
744 			return -EINVAL;
745 	} else {
746 		sgmii = true; /* Phy is connected to the MAC */
747 	}
748 
749 	/* Choose SGMII or 1000BaseX/2500BaseX PCS mode */
750 	spx5_rmw(DEV2G5_PCS1G_MODE_CFG_SGMII_MODE_ENA_SET(sgmii),
751 		 DEV2G5_PCS1G_MODE_CFG_SGMII_MODE_ENA,
752 		 sparx5,
753 		 DEV2G5_PCS1G_MODE_CFG(port->portno));
754 
755 	/* Enable PCS */
756 	spx5_wr(DEV2G5_PCS1G_CFG_PCS_ENA_SET(1),
757 		sparx5,
758 		DEV2G5_PCS1G_CFG(port->portno));
759 
760 	if (inband_aneg) {
761 		u16 abil = sparx5_get_aneg_word(conf);
762 
763 		/* Enable in-band aneg */
764 		spx5_wr(DEV2G5_PCS1G_ANEG_CFG_ADV_ABILITY_SET(abil) |
765 			DEV2G5_PCS1G_ANEG_CFG_SW_RESOLVE_ENA_SET(1) |
766 			DEV2G5_PCS1G_ANEG_CFG_ANEG_ENA_SET(1) |
767 			DEV2G5_PCS1G_ANEG_CFG_ANEG_RESTART_ONE_SHOT_SET(1),
768 			sparx5,
769 			DEV2G5_PCS1G_ANEG_CFG(port->portno));
770 	} else {
771 		spx5_wr(0, sparx5, DEV2G5_PCS1G_ANEG_CFG(port->portno));
772 	}
773 
774 	/* Take PCS out of reset */
775 	spx5_rmw(DEV2G5_DEV_RST_CTRL_SPEED_SEL_SET(2) |
776 		 DEV2G5_DEV_RST_CTRL_PCS_TX_RST_SET(0) |
777 		 DEV2G5_DEV_RST_CTRL_PCS_RX_RST_SET(0),
778 		 DEV2G5_DEV_RST_CTRL_SPEED_SEL |
779 		 DEV2G5_DEV_RST_CTRL_PCS_TX_RST |
780 		 DEV2G5_DEV_RST_CTRL_PCS_RX_RST,
781 		 sparx5,
782 		 DEV2G5_DEV_RST_CTRL(port->portno));
783 
784 	return 0;
785 }
786 
sparx5_port_pcs_high_set(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)787 static int sparx5_port_pcs_high_set(struct sparx5 *sparx5,
788 				    struct sparx5_port *port,
789 				    struct sparx5_port_config *conf)
790 {
791 	u32 clk_spd = conf->portmode == PHY_INTERFACE_MODE_5GBASER ? 1 : 0;
792 	u32 pix = sparx5_port_dev_index(port->portno);
793 	u32 dev = sparx5_to_high_dev(port->portno);
794 	u32 pcs = sparx5_to_pcs_dev(port->portno);
795 	void __iomem *devinst;
796 	void __iomem *pcsinst;
797 	int err;
798 
799 	devinst = spx5_inst_get(sparx5, dev, pix);
800 	pcsinst = spx5_inst_get(sparx5, pcs, pix);
801 
802 	/*  SFI : No in-band-aneg. Speeds 5G/10G/25G */
803 	err = sparx5_serdes_set(sparx5, port, conf);
804 	if (err)
805 		return -EINVAL;
806 	if (conf->portmode == PHY_INTERFACE_MODE_25GBASER) {
807 		/* Enable PCS for 25G device, speed 25G */
808 		spx5_rmw(DEV25G_PCS25G_CFG_PCS25G_ENA_SET(1),
809 			 DEV25G_PCS25G_CFG_PCS25G_ENA,
810 			 sparx5,
811 			 DEV25G_PCS25G_CFG(pix));
812 	} else {
813 		/* Enable PCS for 5G/10G/25G devices, speed 5G/10G */
814 		spx5_inst_rmw(PCS10G_BR_PCS_CFG_PCS_ENA_SET(1),
815 			      PCS10G_BR_PCS_CFG_PCS_ENA,
816 			      pcsinst,
817 			      PCS10G_BR_PCS_CFG(0));
818 	}
819 
820 	/* Enable 5G/10G/25G MAC module */
821 	spx5_inst_wr(DEV10G_MAC_ENA_CFG_RX_ENA_SET(1) |
822 		     DEV10G_MAC_ENA_CFG_TX_ENA_SET(1),
823 		     devinst,
824 		     DEV10G_MAC_ENA_CFG(0));
825 
826 	/* Take the device out of reset */
827 	spx5_inst_rmw(DEV10G_DEV_RST_CTRL_PCS_RX_RST_SET(0) |
828 		      DEV10G_DEV_RST_CTRL_PCS_TX_RST_SET(0) |
829 		      DEV10G_DEV_RST_CTRL_MAC_RX_RST_SET(0) |
830 		      DEV10G_DEV_RST_CTRL_MAC_TX_RST_SET(0) |
831 		      DEV10G_DEV_RST_CTRL_SPEED_SEL_SET(clk_spd),
832 		      DEV10G_DEV_RST_CTRL_PCS_RX_RST |
833 		      DEV10G_DEV_RST_CTRL_PCS_TX_RST |
834 		      DEV10G_DEV_RST_CTRL_MAC_RX_RST |
835 		      DEV10G_DEV_RST_CTRL_MAC_TX_RST |
836 		      DEV10G_DEV_RST_CTRL_SPEED_SEL,
837 		      devinst,
838 		      DEV10G_DEV_RST_CTRL(0));
839 
840 	return 0;
841 }
842 
843 /* Switch between 1G/2500 and 5G/10G/25G devices */
sparx5_dev_switch(struct sparx5 * sparx5,int port,bool hsd)844 static void sparx5_dev_switch(struct sparx5 *sparx5, int port, bool hsd)
845 {
846 	int bt_indx = BIT(sparx5_port_dev_index(port));
847 
848 	if (sparx5_port_is_5g(port)) {
849 		spx5_rmw(hsd ? 0 : bt_indx,
850 			 bt_indx,
851 			 sparx5,
852 			 PORT_CONF_DEV5G_MODES);
853 	} else if (sparx5_port_is_10g(port)) {
854 		spx5_rmw(hsd ? 0 : bt_indx,
855 			 bt_indx,
856 			 sparx5,
857 			 PORT_CONF_DEV10G_MODES);
858 	} else if (sparx5_port_is_25g(port)) {
859 		spx5_rmw(hsd ? 0 : bt_indx,
860 			 bt_indx,
861 			 sparx5,
862 			 PORT_CONF_DEV25G_MODES);
863 	}
864 }
865 
866 /* Configure speed/duplex dependent registers */
sparx5_port_config_low_set(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)867 static int sparx5_port_config_low_set(struct sparx5 *sparx5,
868 				      struct sparx5_port *port,
869 				      struct sparx5_port_config *conf)
870 {
871 	u32 clk_spd, gig_mode, tx_gap, hdx_gap_1, hdx_gap_2;
872 	bool fdx = conf->duplex == DUPLEX_FULL;
873 	int spd = conf->speed;
874 
875 	clk_spd = spd == SPEED_10 ? 0 : spd == SPEED_100 ? 1 : 2;
876 	gig_mode = spd == SPEED_1000 || spd == SPEED_2500;
877 	tx_gap = spd == SPEED_1000 ? 4 : fdx ? 6 : 5;
878 	hdx_gap_1 = spd == SPEED_1000 ? 0 : spd == SPEED_100 ? 1 : 2;
879 	hdx_gap_2 = spd == SPEED_1000 ? 0 : spd == SPEED_100 ? 4 : 1;
880 
881 	/* GIG/FDX mode */
882 	spx5_rmw(DEV2G5_MAC_MODE_CFG_GIGA_MODE_ENA_SET(gig_mode) |
883 		 DEV2G5_MAC_MODE_CFG_FDX_ENA_SET(fdx),
884 		 DEV2G5_MAC_MODE_CFG_GIGA_MODE_ENA |
885 		 DEV2G5_MAC_MODE_CFG_FDX_ENA,
886 		 sparx5,
887 		 DEV2G5_MAC_MODE_CFG(port->portno));
888 
889 	/* Set MAC IFG Gaps */
890 	spx5_wr(DEV2G5_MAC_IFG_CFG_TX_IFG_SET(tx_gap) |
891 		DEV2G5_MAC_IFG_CFG_RX_IFG1_SET(hdx_gap_1) |
892 		DEV2G5_MAC_IFG_CFG_RX_IFG2_SET(hdx_gap_2),
893 		sparx5,
894 		DEV2G5_MAC_IFG_CFG(port->portno));
895 
896 	/* Disabling frame aging when in HDX (due to HDX issue) */
897 	spx5_rmw(HSCH_PORT_MODE_AGE_DIS_SET(fdx == 0),
898 		 HSCH_PORT_MODE_AGE_DIS,
899 		 sparx5,
900 		 HSCH_PORT_MODE(port->portno));
901 
902 	/* Enable MAC module */
903 	spx5_wr(DEV2G5_MAC_ENA_CFG_RX_ENA |
904 		DEV2G5_MAC_ENA_CFG_TX_ENA,
905 		sparx5,
906 		DEV2G5_MAC_ENA_CFG(port->portno));
907 
908 	/* Select speed and take MAC out of reset */
909 	spx5_rmw(DEV2G5_DEV_RST_CTRL_SPEED_SEL_SET(clk_spd) |
910 		 DEV2G5_DEV_RST_CTRL_MAC_TX_RST_SET(0) |
911 		 DEV2G5_DEV_RST_CTRL_MAC_RX_RST_SET(0),
912 		 DEV2G5_DEV_RST_CTRL_SPEED_SEL |
913 		 DEV2G5_DEV_RST_CTRL_MAC_TX_RST |
914 		 DEV2G5_DEV_RST_CTRL_MAC_RX_RST,
915 		 sparx5,
916 		 DEV2G5_DEV_RST_CTRL(port->portno));
917 
918 	return 0;
919 }
920 
sparx5_port_pcs_set(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)921 int sparx5_port_pcs_set(struct sparx5 *sparx5,
922 			struct sparx5_port *port,
923 			struct sparx5_port_config *conf)
924 
925 {
926 	bool high_speed_dev = sparx5_is_baser(conf->portmode);
927 	int err;
928 
929 	if (sparx5_dev_change(sparx5, port, conf)) {
930 		/* switch device */
931 		sparx5_dev_switch(sparx5, port->portno, high_speed_dev);
932 
933 		/* Disable the not-in-use device */
934 		err = sparx5_port_disable(sparx5, port, !high_speed_dev);
935 		if (err)
936 			return err;
937 	}
938 	/* Disable the port before re-configuring */
939 	err = sparx5_port_disable(sparx5, port, high_speed_dev);
940 	if (err)
941 		return -EINVAL;
942 
943 	if (high_speed_dev)
944 		err = sparx5_port_pcs_high_set(sparx5, port, conf);
945 	else
946 		err = sparx5_port_pcs_low_set(sparx5, port, conf);
947 
948 	if (err)
949 		return -EINVAL;
950 
951 	if (port->conf.inband) {
952 		/* Enable/disable 1G counters in ASM */
953 		spx5_rmw(ASM_PORT_CFG_CSC_STAT_DIS_SET(high_speed_dev),
954 			 ASM_PORT_CFG_CSC_STAT_DIS,
955 			 sparx5,
956 			 ASM_PORT_CFG(port->portno));
957 
958 		/* Enable/disable 1G counters in DSM */
959 		spx5_rmw(DSM_BUF_CFG_CSC_STAT_DIS_SET(high_speed_dev),
960 			 DSM_BUF_CFG_CSC_STAT_DIS,
961 			 sparx5,
962 			 DSM_BUF_CFG(port->portno));
963 	}
964 
965 	port->conf = *conf;
966 
967 	return 0;
968 }
969 
sparx5_port_config(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)970 int sparx5_port_config(struct sparx5 *sparx5,
971 		       struct sparx5_port *port,
972 		       struct sparx5_port_config *conf)
973 {
974 	bool high_speed_dev = sparx5_is_baser(conf->portmode);
975 	int err, urgency, stop_wm;
976 
977 	err = sparx5_port_verify_speed(sparx5, port, conf);
978 	if (err)
979 		return err;
980 
981 	/* high speed device is already configured */
982 	if (!high_speed_dev)
983 		sparx5_port_config_low_set(sparx5, port, conf);
984 
985 	/* Configure flow control */
986 	err = sparx5_port_fc_setup(sparx5, port, conf);
987 	if (err)
988 		return err;
989 
990 	/* Set the DSM stop watermark */
991 	stop_wm = sparx5_port_fifo_sz(sparx5, port->portno, conf->speed);
992 	spx5_rmw(DSM_DEV_TX_STOP_WM_CFG_DEV_TX_STOP_WM_SET(stop_wm),
993 		 DSM_DEV_TX_STOP_WM_CFG_DEV_TX_STOP_WM,
994 		 sparx5,
995 		 DSM_DEV_TX_STOP_WM_CFG(port->portno));
996 
997 	/* Enable port in queue system */
998 	urgency = sparx5_port_fwd_urg(sparx5, conf->speed);
999 	spx5_rmw(QFWD_SWITCH_PORT_MODE_PORT_ENA_SET(1) |
1000 		 QFWD_SWITCH_PORT_MODE_FWD_URGENCY_SET(urgency),
1001 		 QFWD_SWITCH_PORT_MODE_PORT_ENA |
1002 		 QFWD_SWITCH_PORT_MODE_FWD_URGENCY,
1003 		 sparx5,
1004 		 QFWD_SWITCH_PORT_MODE(port->portno));
1005 
1006 	/* Save the new values */
1007 	port->conf = *conf;
1008 
1009 	return 0;
1010 }
1011 
1012 /* Initialize port config to default */
sparx5_port_init(struct sparx5 * sparx5,struct sparx5_port * port,struct sparx5_port_config * conf)1013 int sparx5_port_init(struct sparx5 *sparx5,
1014 		     struct sparx5_port *port,
1015 		     struct sparx5_port_config *conf)
1016 {
1017 	u32 pause_start = sparx5_wm_enc(6  * (ETH_MAXLEN / SPX5_BUFFER_CELL_SZ));
1018 	u32 atop = sparx5_wm_enc(20 * (ETH_MAXLEN / SPX5_BUFFER_CELL_SZ));
1019 	u32 devhigh = sparx5_to_high_dev(port->portno);
1020 	u32 pix = sparx5_port_dev_index(port->portno);
1021 	u32 pcs = sparx5_to_pcs_dev(port->portno);
1022 	bool sd_pol = port->signd_active_high;
1023 	bool sd_sel = !port->signd_internal;
1024 	bool sd_ena = port->signd_enable;
1025 	u32 pause_stop = 0xFFF - 1; /* FC generate disabled */
1026 	void __iomem *devinst;
1027 	void __iomem *pcsinst;
1028 	int err;
1029 
1030 	devinst = spx5_inst_get(sparx5, devhigh, pix);
1031 	pcsinst = spx5_inst_get(sparx5, pcs, pix);
1032 
1033 	/* Set the mux port mode  */
1034 	err = sparx5_port_mux_set(sparx5, port, conf);
1035 	if (err)
1036 		return err;
1037 
1038 	/* Configure MAC vlan awareness */
1039 	err = sparx5_port_max_tags_set(sparx5, port);
1040 	if (err)
1041 		return err;
1042 
1043 	/* Set Max Length */
1044 	spx5_rmw(DEV2G5_MAC_MAXLEN_CFG_MAX_LEN_SET(ETH_MAXLEN),
1045 		 DEV2G5_MAC_MAXLEN_CFG_MAX_LEN,
1046 		 sparx5,
1047 		 DEV2G5_MAC_MAXLEN_CFG(port->portno));
1048 
1049 	/* 1G/2G5: Signal Detect configuration */
1050 	spx5_wr(DEV2G5_PCS1G_SD_CFG_SD_POL_SET(sd_pol) |
1051 		DEV2G5_PCS1G_SD_CFG_SD_SEL_SET(sd_sel) |
1052 		DEV2G5_PCS1G_SD_CFG_SD_ENA_SET(sd_ena),
1053 		sparx5,
1054 		DEV2G5_PCS1G_SD_CFG(port->portno));
1055 
1056 	/* Set Pause WM hysteresis */
1057 	spx5_rmw(QSYS_PAUSE_CFG_PAUSE_START_SET(pause_start) |
1058 		 QSYS_PAUSE_CFG_PAUSE_STOP_SET(pause_stop) |
1059 		 QSYS_PAUSE_CFG_PAUSE_ENA_SET(1),
1060 		 QSYS_PAUSE_CFG_PAUSE_START |
1061 		 QSYS_PAUSE_CFG_PAUSE_STOP |
1062 		 QSYS_PAUSE_CFG_PAUSE_ENA,
1063 		 sparx5,
1064 		 QSYS_PAUSE_CFG(port->portno));
1065 
1066 	/* Port ATOP. Frames are tail dropped when this WM is hit */
1067 	spx5_wr(QSYS_ATOP_ATOP_SET(atop),
1068 		sparx5,
1069 		QSYS_ATOP(port->portno));
1070 
1071 	/* Discard pause frame 01-80-C2-00-00-01 */
1072 	spx5_wr(PAUSE_DISCARD, sparx5, ANA_CL_CAPTURE_BPDU_CFG(port->portno));
1073 
1074 	/* Discard SMAC multicast */
1075 	spx5_rmw(ANA_CL_FILTER_CTRL_FILTER_SMAC_MC_DIS_SET(0),
1076 		 ANA_CL_FILTER_CTRL_FILTER_SMAC_MC_DIS,
1077 		 sparx5, ANA_CL_FILTER_CTRL(port->portno));
1078 
1079 	if (conf->portmode == PHY_INTERFACE_MODE_QSGMII ||
1080 	    conf->portmode == PHY_INTERFACE_MODE_SGMII) {
1081 		err = sparx5_serdes_set(sparx5, port, conf);
1082 		if (err)
1083 			return err;
1084 
1085 		if (!sparx5_port_is_2g5(port->portno))
1086 			/* Enable shadow device */
1087 			spx5_rmw(DSM_DEV_TX_STOP_WM_CFG_DEV10G_SHADOW_ENA_SET(1),
1088 				 DSM_DEV_TX_STOP_WM_CFG_DEV10G_SHADOW_ENA,
1089 				 sparx5,
1090 				 DSM_DEV_TX_STOP_WM_CFG(port->portno));
1091 
1092 		sparx5_dev_switch(sparx5, port->portno, false);
1093 	}
1094 	if (conf->portmode == PHY_INTERFACE_MODE_QSGMII) {
1095 		// All ports must be PCS enabled in QSGMII mode
1096 		spx5_rmw(DEV2G5_DEV_RST_CTRL_PCS_TX_RST_SET(0),
1097 			 DEV2G5_DEV_RST_CTRL_PCS_TX_RST,
1098 			 sparx5,
1099 			 DEV2G5_DEV_RST_CTRL(port->portno));
1100 	}
1101 	/* Default IFGs for 1G */
1102 	spx5_wr(DEV2G5_MAC_IFG_CFG_TX_IFG_SET(6) |
1103 		DEV2G5_MAC_IFG_CFG_RX_IFG1_SET(0) |
1104 		DEV2G5_MAC_IFG_CFG_RX_IFG2_SET(0),
1105 		sparx5,
1106 		DEV2G5_MAC_IFG_CFG(port->portno));
1107 
1108 	if (sparx5_port_is_2g5(port->portno))
1109 		return 0; /* Low speed device only - return */
1110 
1111 	/* Now setup the high speed device */
1112 	if (conf->portmode == PHY_INTERFACE_MODE_NA)
1113 		conf->portmode = PHY_INTERFACE_MODE_10GBASER;
1114 
1115 	if (sparx5_is_baser(conf->portmode))
1116 		sparx5_dev_switch(sparx5, port->portno, true);
1117 
1118 	/* Set Max Length */
1119 	spx5_inst_rmw(DEV10G_MAC_MAXLEN_CFG_MAX_LEN_SET(ETH_MAXLEN),
1120 		      DEV10G_MAC_MAXLEN_CFG_MAX_LEN,
1121 		      devinst,
1122 		      DEV10G_MAC_ENA_CFG(0));
1123 
1124 	/* Handle Signal Detect in 10G PCS */
1125 	spx5_inst_wr(PCS10G_BR_PCS_SD_CFG_SD_POL_SET(sd_pol) |
1126 		     PCS10G_BR_PCS_SD_CFG_SD_SEL_SET(sd_sel) |
1127 		     PCS10G_BR_PCS_SD_CFG_SD_ENA_SET(sd_ena),
1128 		     pcsinst,
1129 		     PCS10G_BR_PCS_SD_CFG(0));
1130 
1131 	if (sparx5_port_is_25g(port->portno)) {
1132 		/* Handle Signal Detect in 25G PCS */
1133 		spx5_wr(DEV25G_PCS25G_SD_CFG_SD_POL_SET(sd_pol) |
1134 			DEV25G_PCS25G_SD_CFG_SD_SEL_SET(sd_sel) |
1135 			DEV25G_PCS25G_SD_CFG_SD_ENA_SET(sd_ena),
1136 			sparx5,
1137 			DEV25G_PCS25G_SD_CFG(pix));
1138 	}
1139 
1140 	return 0;
1141 }
1142 
sparx5_port_enable(struct sparx5_port * port,bool enable)1143 void sparx5_port_enable(struct sparx5_port *port, bool enable)
1144 {
1145 	struct sparx5 *sparx5 = port->sparx5;
1146 
1147 	/* Enable port for frame transfer? */
1148 	spx5_rmw(QFWD_SWITCH_PORT_MODE_PORT_ENA_SET(enable),
1149 		 QFWD_SWITCH_PORT_MODE_PORT_ENA,
1150 		 sparx5,
1151 		 QFWD_SWITCH_PORT_MODE(port->portno));
1152 }
1153 
sparx5_port_qos_set(struct sparx5_port * port,struct sparx5_port_qos * qos)1154 int sparx5_port_qos_set(struct sparx5_port *port,
1155 			struct sparx5_port_qos *qos)
1156 {
1157 	sparx5_port_qos_dscp_set(port, &qos->dscp);
1158 	sparx5_port_qos_pcp_set(port, &qos->pcp);
1159 	sparx5_port_qos_pcp_rewr_set(port, &qos->pcp_rewr);
1160 	sparx5_port_qos_dscp_rewr_set(port, &qos->dscp_rewr);
1161 	sparx5_port_qos_default_set(port, qos);
1162 
1163 	return 0;
1164 }
1165 
sparx5_port_qos_pcp_rewr_set(const struct sparx5_port * port,struct sparx5_port_qos_pcp_rewr * qos)1166 int sparx5_port_qos_pcp_rewr_set(const struct sparx5_port *port,
1167 				 struct sparx5_port_qos_pcp_rewr *qos)
1168 {
1169 	int i, mode = SPARX5_PORT_REW_TAG_CTRL_CLASSIFIED;
1170 	struct sparx5 *sparx5 = port->sparx5;
1171 	u8 pcp, dei;
1172 
1173 	/* Use mapping table, with classified QoS as index, to map QoS and DP
1174 	 * to tagged PCP and DEI, if PCP is trusted. Otherwise use classified
1175 	 * PCP. Classified PCP equals frame PCP.
1176 	 */
1177 	if (qos->enable)
1178 		mode = SPARX5_PORT_REW_TAG_CTRL_MAPPED;
1179 
1180 	spx5_rmw(REW_TAG_CTRL_TAG_PCP_CFG_SET(mode) |
1181 		 REW_TAG_CTRL_TAG_DEI_CFG_SET(mode),
1182 		 REW_TAG_CTRL_TAG_PCP_CFG | REW_TAG_CTRL_TAG_DEI_CFG,
1183 		 port->sparx5, REW_TAG_CTRL(port->portno));
1184 
1185 	for (i = 0; i < ARRAY_SIZE(qos->map.map); i++) {
1186 		/* Extract PCP and DEI */
1187 		pcp = qos->map.map[i];
1188 		if (pcp > SPARX5_PORT_QOS_PCP_COUNT)
1189 			dei = 1;
1190 		else
1191 			dei = 0;
1192 
1193 		/* Rewrite PCP and DEI, for each classified QoS class and DP
1194 		 * level. This table is only used if tag ctrl mode is set to
1195 		 * 'mapped'.
1196 		 *
1197 		 * 0:0nd   - prio=0 and dp:0 => pcp=0 and dei=0
1198 		 * 0:0de   - prio=0 and dp:1 => pcp=0 and dei=1
1199 		 */
1200 		if (dei) {
1201 			spx5_rmw(REW_PCP_MAP_DE1_PCP_DE1_SET(pcp),
1202 				 REW_PCP_MAP_DE1_PCP_DE1, sparx5,
1203 				 REW_PCP_MAP_DE1(port->portno, i));
1204 
1205 			spx5_rmw(REW_DEI_MAP_DE1_DEI_DE1_SET(dei),
1206 				 REW_DEI_MAP_DE1_DEI_DE1, port->sparx5,
1207 				 REW_DEI_MAP_DE1(port->portno, i));
1208 		} else {
1209 			spx5_rmw(REW_PCP_MAP_DE0_PCP_DE0_SET(pcp),
1210 				 REW_PCP_MAP_DE0_PCP_DE0, sparx5,
1211 				 REW_PCP_MAP_DE0(port->portno, i));
1212 
1213 			spx5_rmw(REW_DEI_MAP_DE0_DEI_DE0_SET(dei),
1214 				 REW_DEI_MAP_DE0_DEI_DE0, port->sparx5,
1215 				 REW_DEI_MAP_DE0(port->portno, i));
1216 		}
1217 	}
1218 
1219 	return 0;
1220 }
1221 
sparx5_port_qos_pcp_set(const struct sparx5_port * port,struct sparx5_port_qos_pcp * qos)1222 int sparx5_port_qos_pcp_set(const struct sparx5_port *port,
1223 			    struct sparx5_port_qos_pcp *qos)
1224 {
1225 	struct sparx5 *sparx5 = port->sparx5;
1226 	u8 *pcp_itr = qos->map.map;
1227 	u8 pcp, dp;
1228 	int i;
1229 
1230 	/* Enable/disable pcp and dp for qos classification. */
1231 	spx5_rmw(ANA_CL_QOS_CFG_PCP_DEI_QOS_ENA_SET(qos->qos_enable) |
1232 		 ANA_CL_QOS_CFG_PCP_DEI_DP_ENA_SET(qos->dp_enable),
1233 		 ANA_CL_QOS_CFG_PCP_DEI_QOS_ENA | ANA_CL_QOS_CFG_PCP_DEI_DP_ENA,
1234 		 sparx5, ANA_CL_QOS_CFG(port->portno));
1235 
1236 	/* Map each pcp and dei value to priority and dp */
1237 	for (i = 0; i < ARRAY_SIZE(qos->map.map); i++) {
1238 		pcp = *(pcp_itr + i);
1239 		dp = (i < SPARX5_PORT_QOS_PCP_COUNT) ? 0 : 1;
1240 		spx5_rmw(ANA_CL_PCP_DEI_MAP_CFG_PCP_DEI_QOS_VAL_SET(pcp) |
1241 			 ANA_CL_PCP_DEI_MAP_CFG_PCP_DEI_DP_VAL_SET(dp),
1242 			 ANA_CL_PCP_DEI_MAP_CFG_PCP_DEI_QOS_VAL |
1243 			 ANA_CL_PCP_DEI_MAP_CFG_PCP_DEI_DP_VAL, sparx5,
1244 			 ANA_CL_PCP_DEI_MAP_CFG(port->portno, i));
1245 	}
1246 
1247 	return 0;
1248 }
1249 
sparx5_port_qos_dscp_rewr_mode_set(const struct sparx5_port * port,int mode)1250 void sparx5_port_qos_dscp_rewr_mode_set(const struct sparx5_port *port,
1251 					int mode)
1252 {
1253 	spx5_rmw(ANA_CL_QOS_CFG_DSCP_REWR_MODE_SEL_SET(mode),
1254 		 ANA_CL_QOS_CFG_DSCP_REWR_MODE_SEL, port->sparx5,
1255 		 ANA_CL_QOS_CFG(port->portno));
1256 }
1257 
sparx5_port_qos_dscp_rewr_set(const struct sparx5_port * port,struct sparx5_port_qos_dscp_rewr * qos)1258 int sparx5_port_qos_dscp_rewr_set(const struct sparx5_port *port,
1259 				  struct sparx5_port_qos_dscp_rewr *qos)
1260 {
1261 	struct sparx5 *sparx5 = port->sparx5;
1262 	bool rewr = false;
1263 	u16 dscp;
1264 	int i;
1265 
1266 	/* On egress, rewrite DSCP value to either classified DSCP or frame
1267 	 * DSCP. If enabled; classified DSCP, if disabled; frame DSCP.
1268 	 */
1269 	if (qos->enable)
1270 		rewr = true;
1271 
1272 	spx5_rmw(REW_DSCP_MAP_DSCP_UPDATE_ENA_SET(rewr),
1273 		 REW_DSCP_MAP_DSCP_UPDATE_ENA, sparx5,
1274 		 REW_DSCP_MAP(port->portno));
1275 
1276 	/* On ingress, map each classified QoS class and DP to classified DSCP
1277 	 * value. This mapping table is global for all ports.
1278 	 */
1279 	for (i = 0; i < ARRAY_SIZE(qos->map.map); i++) {
1280 		dscp = qos->map.map[i];
1281 		spx5_rmw(ANA_CL_QOS_MAP_CFG_DSCP_REWR_VAL_SET(dscp),
1282 			 ANA_CL_QOS_MAP_CFG_DSCP_REWR_VAL, sparx5,
1283 			 ANA_CL_QOS_MAP_CFG(i));
1284 	}
1285 
1286 	return 0;
1287 }
1288 
sparx5_port_qos_dscp_set(const struct sparx5_port * port,struct sparx5_port_qos_dscp * qos)1289 int sparx5_port_qos_dscp_set(const struct sparx5_port *port,
1290 			     struct sparx5_port_qos_dscp *qos)
1291 {
1292 	struct sparx5 *sparx5 = port->sparx5;
1293 	u8 *dscp = qos->map.map;
1294 	int i;
1295 
1296 	/* Enable/disable dscp and dp for qos classification.
1297 	 * Disable rewrite of dscp values for now.
1298 	 */
1299 	spx5_rmw(ANA_CL_QOS_CFG_DSCP_QOS_ENA_SET(qos->qos_enable) |
1300 		 ANA_CL_QOS_CFG_DSCP_DP_ENA_SET(qos->dp_enable) |
1301 		 ANA_CL_QOS_CFG_DSCP_KEEP_ENA_SET(1),
1302 		 ANA_CL_QOS_CFG_DSCP_QOS_ENA | ANA_CL_QOS_CFG_DSCP_DP_ENA |
1303 		 ANA_CL_QOS_CFG_DSCP_KEEP_ENA, sparx5,
1304 		 ANA_CL_QOS_CFG(port->portno));
1305 
1306 	/* Map each dscp value to priority and dp */
1307 	for (i = 0; i < ARRAY_SIZE(qos->map.map); i++) {
1308 		spx5_rmw(ANA_CL_DSCP_CFG_DSCP_QOS_VAL_SET(*(dscp + i)) |
1309 			 ANA_CL_DSCP_CFG_DSCP_DP_VAL_SET(0),
1310 			 ANA_CL_DSCP_CFG_DSCP_QOS_VAL |
1311 			 ANA_CL_DSCP_CFG_DSCP_DP_VAL, sparx5,
1312 			 ANA_CL_DSCP_CFG(i));
1313 	}
1314 
1315 	/* Set per-dscp trust */
1316 	for (i = 0; i <  ARRAY_SIZE(qos->map.map); i++) {
1317 		if (qos->qos_enable) {
1318 			spx5_rmw(ANA_CL_DSCP_CFG_DSCP_TRUST_ENA_SET(1),
1319 				 ANA_CL_DSCP_CFG_DSCP_TRUST_ENA, sparx5,
1320 				 ANA_CL_DSCP_CFG(i));
1321 		}
1322 	}
1323 
1324 	return 0;
1325 }
1326 
sparx5_port_qos_default_set(const struct sparx5_port * port,const struct sparx5_port_qos * qos)1327 int sparx5_port_qos_default_set(const struct sparx5_port *port,
1328 				const struct sparx5_port_qos *qos)
1329 {
1330 	struct sparx5 *sparx5 = port->sparx5;
1331 
1332 	/* Set default prio and dp level */
1333 	spx5_rmw(ANA_CL_QOS_CFG_DEFAULT_QOS_VAL_SET(qos->default_prio) |
1334 		 ANA_CL_QOS_CFG_DEFAULT_DP_VAL_SET(0),
1335 		 ANA_CL_QOS_CFG_DEFAULT_QOS_VAL |
1336 		 ANA_CL_QOS_CFG_DEFAULT_DP_VAL,
1337 		 sparx5, ANA_CL_QOS_CFG(port->portno));
1338 
1339 	/* Set default pcp and dei for untagged frames */
1340 	spx5_rmw(ANA_CL_VLAN_CTRL_PORT_PCP_SET(0) |
1341 		 ANA_CL_VLAN_CTRL_PORT_DEI_SET(0),
1342 		 ANA_CL_VLAN_CTRL_PORT_PCP |
1343 		 ANA_CL_VLAN_CTRL_PORT_DEI,
1344 		 sparx5, ANA_CL_VLAN_CTRL(port->portno));
1345 
1346 	return 0;
1347 }
1348