1 /*********************************************************************
2 *                    SEGGER Microcontroller GmbH                     *
3 *                        The Embedded Experts                        *
4 **********************************************************************
5 *                                                                    *
6 *            (c) 1995 - 2021 SEGGER Microcontroller GmbH             *
7 *                                                                    *
8 *       www.segger.com     Support: support@segger.com               *
9 *                                                                    *
10 **********************************************************************
11 *                                                                    *
12 *       SEGGER SystemView * Real-time application analysis           *
13 *                                                                    *
14 **********************************************************************
15 *                                                                    *
16 * All rights reserved.                                               *
17 *                                                                    *
18 * SEGGER strongly recommends to not make any changes                 *
19 * to or modify the source code of this software in order to stay     *
20 * compatible with the SystemView and RTT protocol, and J-Link.       *
21 *                                                                    *
22 * Redistribution and use in source and binary forms, with or         *
23 * without modification, are permitted provided that the following    *
24 * condition is met:                                                  *
25 *                                                                    *
26 * o Redistributions of source code must retain the above copyright   *
27 *   notice, this condition and the following disclaimer.             *
28 *                                                                    *
29 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND             *
30 * CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,        *
31 * INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF           *
32 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE           *
33 * DISCLAIMED. IN NO EVENT SHALL SEGGER Microcontroller BE LIABLE FOR *
34 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR           *
35 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT  *
36 * OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;    *
37 * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF      *
38 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT          *
39 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE  *
40 * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH   *
41 * DAMAGE.                                                            *
42 *                                                                    *
43 **********************************************************************
44 *                                                                    *
45 *       SystemView version: 3.30                                    *
46 *                                                                    *
47 **********************************************************************
48 -------------------------- END-OF-HEADER -----------------------------
49 
50 File    : SEGGER_SYSVIEW_Conf.h
51 Purpose : SEGGER SystemView configuration file.
52           Set defines which deviate from the defaults (see SEGGER_SYSVIEW_ConfDefaults.h) here.
53 Revision: $Rev: 21292 $
54 
55 Additional information:
56   Required defines which must be set are:
57     SEGGER_SYSVIEW_GET_TIMESTAMP
58     SEGGER_SYSVIEW_GET_INTERRUPT_ID
59   For known compilers and cores, these might be set to good defaults
60   in SEGGER_SYSVIEW_ConfDefaults.h.
61 
62   SystemView needs a (nestable) locking mechanism.
63   If not defined, the RTT locking mechanism is used,
64   which then needs to be properly configured.
65 */
66 
67 #ifndef SEGGER_SYSVIEW_CONF_H
68 #define SEGGER_SYSVIEW_CONF_H
69 
70 /*********************************************************************
71 *
72 *       Defines, configurable
73 *
74 **********************************************************************
75 */
76 
77 /*********************************************************************
78 * TODO: Add your defines here.                                       *
79 **********************************************************************
80 */
81 
82 
83 #endif  // SEGGER_SYSVIEW_CONF_H
84 
85 /*************************** End of file ****************************/
86