| /linux-6.3-rc2/arch/powerpc/kernel/ |
| A D | prom_init_check.sh | 59 OK=0
63 OK=1
71 OK=1
74 OK=1
78 if [ $OK -eq 0 ]; then
|
| /linux-6.3-rc2/tools/perf/tests/shell/ |
| A D | test_intel_pt.sh | 100 echo OK
119 echo OK
277 echo OK
430 echo OK
451 echo OK
468 echo OK
497 echo OK
509 echo OK
522 echo OK
565 echo OK
[all …]
|
| /linux-6.3-rc2/drivers/net/plip/ |
| A D | plip.c | 437 return OK; in plip_bh_timeout_error()
478 return OK; in plip_none()
529 return OK; in plip_receive()
695 return OK; in plip_receive_packet()
704 return OK; in plip_receive_packet()
749 return OK; in plip_send()
751 return OK; in plip_send()
870 return OK; in plip_send_packet()
872 return OK; in plip_send_packet()
889 return OK; in plip_connection_close()
[all …]
|
| /linux-6.3-rc2/tools/testing/selftests/netfilter/ |
| A D | nft_trans_stress.sh | 30 local OK="PASS"
33 OK="FAIL"
37 echo "$OK: nft $2 test returned $r"
|
| /linux-6.3-rc2/tools/testing/kunit/test_data/ |
| A D | test_is_test_passed-no_tests_run_no_header.log | 5 Checking if /dev/shm is on tmpfs...OK
6 Checking PROT_EXEC mmap in /dev/shm...OK
30 Checking host MADV_REMOVE support...OK
|
| /linux-6.3-rc2/tools/testing/selftests/net/ |
| A D | ipv6_flowlabel.sh | 37 echo OK. All tests passed
|
| A D | so_txtime.sh | 89 echo OK. All tests passed
|
| /linux-6.3-rc2/Documentation/power/ |
| A D | video.rst | 112 Asus L2400D s3_mode (3) [#f2]_ (S1 also works OK)
114 Asus L3800C (Radeon M7) s3_bios (2) (S1 also works OK)
119 Compaq Armada E500 - P3-700 none (1) (S1 also works OK)
143 HP Omnibook 5150 none (1), (S1 also works OK)
190 Toshiba Satellite 4030CDT s3_mode (3) (S1 also works OK)
191 Toshiba Satellite 4080XCDT s3_mode (3) (S1 also works OK)
|
| /linux-6.3-rc2/drivers/net/fddi/skfp/h/ |
| A D | sba_def.h | 63 #define OK 0x01 /* ??????? */ macro
|
| /linux-6.3-rc2/tools/perf/tests/shell/lib/ |
| A D | waiting.sh | 35 echo OK
|
| /linux-6.3-rc2/Documentation/translations/zh_CN/admin-guide/ |
| A D | sysrq.rst | 186 屏幕上出现 "OK" 和 "Done" 之前，同步还没有发生。
189 被重新挂载为只读。这个重新挂载动作直到你看到 "OK" 和 "Done" 信息出现在屏幕上
|
| /linux-6.3-rc2/Documentation/translations/zh_CN/doc-guide/ |
| A D | kernel-doc.rst | 132 * 0 - OK
138 Return: 0 - OK -EINVAL - invalid argument -ENOMEM - out of memory
143 * * 0 - OK to runtime suspend the device
|
| /linux-6.3-rc2/tools/build/tests/ |
| A D | run.sh | 70 echo OK
|
| /linux-6.3-rc2/Documentation/ABI/testing/ |
| A D | sysfs-bus-dfl-devices-emif | 6 memory interface. "1" for calibration failure, "0" for OK.
|
| /linux-6.3-rc2/Documentation/networking/device_drivers/can/ |
| A D | can327.rst | 135 OK
144 ELM327, a question mark is printed as a response instead of OK::
159 OK
161 OK
282 The ELM327 will reply with OK when a command is understood, and with ?
|
| /linux-6.3-rc2/arch/arm/boot/dts/ |
| A D | sun8i-v3-sl631.dtsi | 61 label = "OK";
|
| A D | logicpd-torpedo-37xx-devkit.dts | 29 * gpio157 is not connected. So this should be OK to keep common for now,
|
| /linux-6.3-rc2/tools/testing/selftests/lkdtm/ |
| A D | tests.txt | 75 STACKLEAK_ERASING OK: the rest of the thread stack is properly erased
|
| /linux-6.3-rc2/tools/perf/Documentation/ |
| A D | perf-daemon.txt | 173 OK cycles
174 OK sched
|
| /linux-6.3-rc2/Documentation/usb/ |
| A D | usbip_protocol.rst | 167 | 4 | 4 | 0x00000000 | Status: 0 for OK |
259 | | | | - 0 for OK |
263 | | | | device, if the previous status field was OK (0), |
|
| A D | acm.rst | 130 If all this seems to be OK, fire up minicom and set it to talk to the ttyACM
131 device and try typing 'at'. If it responds with 'OK', then everything is
|
| A D | gadget_printer.rst | 118 Printer OK
141 To set error status to printer OK::
439 printf(" Printer OK\n");
|
| /linux-6.3-rc2/drivers/net/ethernet/sis/ |
| A D | sis900.h | 200 OK = 0x08000000, DSIZE = 0x00000FFF enumerator
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/arm/ |
| A D | qcom-soc.yaml | 37 # Legacy namings - variations of existing patterns/compatibles are OK,
|
| /linux-6.3-rc2/tools/perf/ |
| A D | builtin-daemon.c | 68 OK, enumerator
185 session->state = OK; in session_config()
989 if (session->state == OK) in daemon__reconfig()
1010 session->state = OK; in daemon__reconfig()
|