Searched refs:CRT (Results 1 – 15 of 15) sorted by relevance
| /linux-6.3-rc2/Documentation/fb/ |
| A D | viafb.rst | 16 Device: CRT, LCD, DVI
20 CRT:
42 viafb_active_dev=CRT+DVI viafb_dvi_port=DVP1
109 This option is used to specify active devices.(CRT, DVI, CRT+LCD...)
121 To enable two devices, such as CRT+DVI::
123 modprobe viafb viafb_active_dev=CRT+DVI;
127 modprobe viafb viafb_active_dev=CRT+DVI
131 modprobe viafb viafb_active_dev=DVI+CRT...
185 1. CRT may not display properly for DuoView CRT & DVI display at
272 Add CRT as output device to iga1::
[all …]
|
| A D | modedb.rst | 104 The GTF is limited by the fact that it is designed mainly for CRT displays.
110 The CVT addresses these limitations. If used with CRT's, the formula used
117 new CRT displays and probably with most flatpanels, if 'reduced blanking'
|
| /linux-6.3-rc2/Documentation/ABI/testing/ |
| A D | sysfs-platform-eeepc-laptop | 9 - 2 = CRT
10 - 3 = LCD+CRT
|
| A D | sysfs-platform-asus-laptop | 11 ||`-- CRT
17 - 3 (0011b) CRT+LCD.
|
| /linux-6.3-rc2/arch/sh/cchips/ |
| A D | Kconfig | 17 CRT color controller, IrDA up to 4 Mbps, and a
|
| /linux-6.3-rc2/drivers/gpu/drm/nouveau/nvkm/engine/disp/ |
| A D | ior.h | 27 CRT, enumerator
|
| A D | outp.c | 65 case DCB_OUTPUT_ANALOG: *type = DAC; return CRT; in nvkm_outp_xlat()
|
| A D | gf119.c | 367 case 0: state->proto = CRT; break; in gf119_dac_state()
|
| A D | nv50.c | 304 case 0: state->proto = CRT; break; in nv50_dac_state()
|
| /linux-6.3-rc2/Documentation/admin-guide/laptops/ |
| A D | asus-laptop.rst | 123 | Bin | Val | DVI | TV | CRT | LCD |
|
| A D | thinkpad-acpi.rst | 657 LCD, CRT or DVI (if available). The following commands are available::
|
| /linux-6.3-rc2/drivers/video/fbdev/ |
| A D | cirrusfb.c | 349 CRT, enumerator
2832 case CRT: in cirrusfb_dbg_print_regs()
2866 cirrusfb_dbg_print_regs(info, regbase, CRT, in cirrusfb_dbg_reg_dump()
|
| A D | Kconfig | 1887 Frame buffer driver for the CRT and LCD controllers in the Silicon
|
| /linux-6.3-rc2/drivers/pinctrl/tegra/ |
| A D | pinctrl-tegra20.c | 2056 MUX_PG(crtp, CRT, RSVD2, RSVD3, RSVD4, 0x20, 14, 0x98, 20, 0xa4, 24),
2113 MUX_PG(lm1, DISPLAYA, DISPLAYB, RSVD3, CRT, 0x1c, 25, 0x90, 28, -1, -1),
|
| A D | pinctrl-tegra30.c | 2348 …PINGROUP(crt_hsync_pv6, CRT, RSVD2, RSVD3, RSVD4, 0x311c, N, …
2349 …PINGROUP(crt_vsync_pv7, CRT, RSVD2, RSVD3, RSVD4, 0x3120, N, …
|
Completed in 32 milliseconds