1 /* SPDX-License-Identifier: GPL-2.0 */
2 /****************************************************************************/
3 
4 /*
5  *	mcfuart.h -- ColdFire internal UART support defines.
6  *
7  *	(C) Copyright 1999-2003, Greg Ungerer (gerg@snapgear.com)
8  * 	(C) Copyright 2000, Lineo Inc. (www.lineo.com)
9  */
10 
11 /****************************************************************************/
12 #ifndef	mcfuart_h
13 #define	mcfuart_h
14 /****************************************************************************/
15 
16 #include <linux/serial_core.h>
17 #include <linux/platform_device.h>
18 
19 struct mcf_platform_uart {
20 	unsigned long	mapbase;	/* Physical address base */
21 	void __iomem	*membase;	/* Virtual address if mapped */
22 	unsigned int	irq;		/* Interrupt vector */
23 	unsigned int	uartclk;	/* UART clock rate */
24 };
25 
26 /*
27  *	Define the ColdFire UART register set addresses.
28  */
29 #define	MCFUART_UMR		0x00		/* Mode register (r/w) */
30 #define	MCFUART_USR		0x04		/* Status register (r) */
31 #define	MCFUART_UCSR		0x04		/* Clock Select (w) */
32 #define	MCFUART_UCR		0x08		/* Command register (w) */
33 #define	MCFUART_URB		0x0c		/* Receiver Buffer (r) */
34 #define	MCFUART_UTB		0x0c		/* Transmit Buffer (w) */
35 #define	MCFUART_UIPCR		0x10		/* Input Port Change (r) */
36 #define	MCFUART_UACR		0x10		/* Auxiliary Control (w) */
37 #define	MCFUART_UISR		0x14		/* Interrupt Status (r) */
38 #define	MCFUART_UIMR		0x14		/* Interrupt Mask (w) */
39 #define	MCFUART_UBG1		0x18		/* Baud Rate MSB (r/w) */
40 #define	MCFUART_UBG2		0x1c		/* Baud Rate LSB (r/w) */
41 #ifdef	CONFIG_M5272
42 #define	MCFUART_UTF		0x28		/* Transmitter FIFO (r/w) */
43 #define	MCFUART_URF		0x2c		/* Receiver FIFO (r/w) */
44 #define	MCFUART_UFPD		0x30		/* Frac Prec. Divider (r/w) */
45 #endif
46 #if defined(CONFIG_M5206) || defined(CONFIG_M5206e) || \
47 	defined(CONFIG_M5249) || defined(CONFIG_M525x) || \
48 	defined(CONFIG_M5307) || defined(CONFIG_M5407)
49 #define	MCFUART_UIVR		0x30		/* Interrupt Vector (r/w) */
50 #endif
51 #define	MCFUART_UIPR		0x34		/* Input Port (r) */
52 #define	MCFUART_UOP1		0x38		/* Output Port Bit Set (w) */
53 #define	MCFUART_UOP0		0x3c		/* Output Port Bit Reset (w) */
54 
55 
56 /*
57  *	Define bit flags in Mode Register 1 (MR1).
58  */
59 #define	MCFUART_MR1_RXRTS	0x80		/* Auto RTS flow control */
60 #define	MCFUART_MR1_RXIRQFULL	0x40		/* RX IRQ type FULL */
61 #define	MCFUART_MR1_RXIRQRDY	0x00		/* RX IRQ type RDY */
62 #define	MCFUART_MR1_RXERRBLOCK	0x20		/* RX block error mode */
63 #define	MCFUART_MR1_RXERRCHAR	0x00		/* RX char error mode */
64 
65 #define	MCFUART_MR1_PARITYNONE	0x10		/* No parity */
66 #define	MCFUART_MR1_PARITYEVEN	0x00		/* Even parity */
67 #define	MCFUART_MR1_PARITYODD	0x04		/* Odd parity */
68 #define	MCFUART_MR1_PARITYSPACE	0x08		/* Space parity */
69 #define	MCFUART_MR1_PARITYMARK	0x0c		/* Mark parity */
70 
71 #define	MCFUART_MR1_CS5		0x00		/* 5 bits per char */
72 #define	MCFUART_MR1_CS6		0x01		/* 6 bits per char */
73 #define	MCFUART_MR1_CS7		0x02		/* 7 bits per char */
74 #define	MCFUART_MR1_CS8		0x03		/* 8 bits per char */
75 
76 /*
77  *	Define bit flags in Mode Register 2 (MR2).
78  */
79 #define	MCFUART_MR2_LOOPBACK	0x80		/* Loopback mode */
80 #define	MCFUART_MR2_REMOTELOOP	0xc0		/* Remote loopback mode */
81 #define	MCFUART_MR2_AUTOECHO	0x40		/* Automatic echo */
82 #define	MCFUART_MR2_TXRTS	0x20		/* Assert RTS on TX */
83 #define	MCFUART_MR2_TXCTS	0x10		/* Auto CTS flow control */
84 
85 #define	MCFUART_MR2_STOP1	0x07		/* 1 stop bit */
86 #define	MCFUART_MR2_STOP15	0x08		/* 1.5 stop bits */
87 #define	MCFUART_MR2_STOP2	0x0f		/* 2 stop bits */
88 
89 /*
90  *	Define bit flags in Status Register (USR).
91  */
92 #define	MCFUART_USR_RXBREAK	0x80		/* Received BREAK */
93 #define	MCFUART_USR_RXFRAMING	0x40		/* Received framing error */
94 #define	MCFUART_USR_RXPARITY	0x20		/* Received parity error */
95 #define	MCFUART_USR_RXOVERRUN	0x10		/* Received overrun error */
96 #define	MCFUART_USR_TXEMPTY	0x08		/* Transmitter empty */
97 #define	MCFUART_USR_TXREADY	0x04		/* Transmitter ready */
98 #define	MCFUART_USR_RXFULL	0x02		/* Receiver full */
99 #define	MCFUART_USR_RXREADY	0x01		/* Receiver ready */
100 
101 #define	MCFUART_USR_RXERR	(MCFUART_USR_RXBREAK | MCFUART_USR_RXFRAMING | \
102 				MCFUART_USR_RXPARITY | MCFUART_USR_RXOVERRUN)
103 
104 /*
105  *	Define bit flags in Clock Select Register (UCSR).
106  */
107 #define	MCFUART_UCSR_RXCLKTIMER	0xd0		/* RX clock is timer */
108 #define	MCFUART_UCSR_RXCLKEXT16	0xe0		/* RX clock is external x16 */
109 #define	MCFUART_UCSR_RXCLKEXT1	0xf0		/* RX clock is external x1 */
110 
111 #define	MCFUART_UCSR_TXCLKTIMER	0x0d		/* TX clock is timer */
112 #define	MCFUART_UCSR_TXCLKEXT16	0x0e		/* TX clock is external x16 */
113 #define	MCFUART_UCSR_TXCLKEXT1	0x0f		/* TX clock is external x1 */
114 
115 /*
116  *	Define bit flags in Command Register (UCR).
117  */
118 #define	MCFUART_UCR_CMDNULL		0x00	/* No command */
119 #define	MCFUART_UCR_CMDRESETMRPTR	0x10	/* Reset MR pointer */
120 #define	MCFUART_UCR_CMDRESETRX		0x20	/* Reset receiver */
121 #define	MCFUART_UCR_CMDRESETTX		0x30	/* Reset transmitter */
122 #define	MCFUART_UCR_CMDRESETERR		0x40	/* Reset error status */
123 #define	MCFUART_UCR_CMDRESETBREAK	0x50	/* Reset BREAK change */
124 #define	MCFUART_UCR_CMDBREAKSTART	0x60	/* Start BREAK */
125 #define	MCFUART_UCR_CMDBREAKSTOP	0x70	/* Stop BREAK */
126 
127 #define	MCFUART_UCR_TXNULL	0x00		/* No TX command */
128 #define	MCFUART_UCR_TXENABLE	0x04		/* Enable TX */
129 #define	MCFUART_UCR_TXDISABLE	0x08		/* Disable TX */
130 #define	MCFUART_UCR_RXNULL	0x00		/* No RX command */
131 #define	MCFUART_UCR_RXENABLE	0x01		/* Enable RX */
132 #define	MCFUART_UCR_RXDISABLE	0x02		/* Disable RX */
133 
134 /*
135  *	Define bit flags in Input Port Change Register (UIPCR).
136  */
137 #define	MCFUART_UIPCR_CTSCOS	0x10		/* CTS change of state */
138 #define	MCFUART_UIPCR_CTS	0x01		/* CTS value */
139 
140 /*
141  *	Define bit flags in Input Port Register (UIP).
142  */
143 #define	MCFUART_UIPR_CTS	0x01		/* CTS value */
144 
145 /*
146  *	Define bit flags in Output Port Registers (UOP).
147  *	Clear bit by writing to UOP0, set by writing to UOP1.
148  */
149 #define	MCFUART_UOP_RTS		0x01		/* RTS set or clear */
150 
151 /*
152  *	Define bit flags in the Auxiliary Control Register (UACR).
153  */
154 #define	MCFUART_UACR_IEC	0x01		/* Input enable control */
155 
156 /*
157  *	Define bit flags in Interrupt Status Register (UISR).
158  *	These same bits are used for the Interrupt Mask Register (UIMR).
159  */
160 #define	MCFUART_UIR_COS		0x80		/* Change of state (CTS) */
161 #define	MCFUART_UIR_DELTABREAK	0x04		/* Break start or stop */
162 #define	MCFUART_UIR_RXREADY	0x02		/* Receiver ready */
163 #define	MCFUART_UIR_TXREADY	0x01		/* Transmitter ready */
164 
165 #ifdef	CONFIG_M5272
166 /*
167  *	Define bit flags in the Transmitter FIFO Register (UTF).
168  */
169 #define	MCFUART_UTF_TXB		0x1f		/* Transmitter data level */
170 #define	MCFUART_UTF_FULL	0x20		/* Transmitter fifo full */
171 #define	MCFUART_UTF_TXS		0xc0		/* Transmitter status */
172 
173 /*
174  *	Define bit flags in the Receiver FIFO Register (URF).
175  */
176 #define	MCFUART_URF_RXB		0x1f		/* Receiver data level */
177 #define	MCFUART_URF_FULL	0x20		/* Receiver fifo full */
178 #define	MCFUART_URF_RXS		0xc0		/* Receiver status */
179 #endif
180 
181 #if defined(CONFIG_M54xx)
182 #define MCFUART_TXFIFOSIZE	512
183 #elif defined(CONFIG_M5272)
184 #define MCFUART_TXFIFOSIZE	25
185 #else
186 #define MCFUART_TXFIFOSIZE	1
187 #endif
188 /****************************************************************************/
189 #endif	/* mcfuart_h */
190