Searched refs:PSI (Results 1 – 16 of 16) sorted by relevance
/linux-6.3-rc2/Documentation/devicetree/bindings/dma/ti/ |
A D | k3-pktdma.yaml | 17 PKTDMA only includes Split channels to service PSI-L based peripherals. 19 The peripherals can be PSI-L native or legacy, non PSI-L native peripherals 20 with PDMAs. PDMA is tasked to act as a bridge between the PSI-L fabric and the 37 The first cell is the PSI-L thread ID of the remote (to PKTDMA) end. 42 Please refer to the device documentation for the PSI-L thread map and also 43 the PSI-L peripheral chapter for the correct thread ID.
|
A D | k3-udma.yaml | 29 on the Rx PSI-L interface. 35 All transfers within NAVSS is done between PSI-L source and destination 37 The peripherals serviced by UDMA can be PSI-L native (sa2ul, cpsw, etc) or 38 legacy, non PSI-L native peripherals. In the later case a special, small PDMA 39 is tasked to act as a bridge between the PSI-L fabric and the legacy 54 The cell is the PSI-L thread ID of the remote (to UDMAP) end. 59 Please refer to the device documentation for the PSI-L thread map and also 60 the PSI-L peripheral chapter for the correct thread ID.
|
A D | k3-bcdma.yaml | 23 Split channels can be used to service PSI-L based peripherals. 24 The peripherals can be PSI-L native or legacy, non PSI-L native peripherals 25 with PDMAs. PDMA is tasked to act as a bridge between the PSI-L fabric and the 56 PSI-L thread ID of the remote (to BCDMA) end. 61 Please refer to the device documentation for the PSI-L thread map and 62 also the PSI-L peripheral chapter for the correct thread ID.
|
/linux-6.3-rc2/Documentation/networking/devlink/ |
A D | iosm.rst | 49 * - ``PSI RAM`` 56 PSI RAM and EBL are the RAM images which are injected to the device when the 70 1) When modem is in Boot ROM stage, user can use below command to inject PSI RAM 80 3) Inject EBL after the modem is in PSI stage.
|
/linux-6.3-rc2/Documentation/driver-api/media/drivers/ |
A D | vidtv.rst | 144 This is the PSI generator. PSI packets contain general information 145 about a MPEG Transport Stream. A PSI generator is needed so 152 Currently vidtv supports working with 5 PSI tables: PAT, PMT, 161 debugging PSI tables. Vidtv currently tries to replicate the PSI 222 #. Inserting PSI and/or PCR packets, if needed. 349 In order to tune into a channel and read the PSI tables, we can use dvb-scan.
|
/linux-6.3-rc2/Documentation/translations/zh_CN/accounting/ |
A D | psi.rst | 10 PSI——压力阻塞信息
|
/linux-6.3-rc2/drivers/gpu/drm/amd/pm/swsmu/inc/ |
A D | smu_types.h | 353 __SMU_DUMMY_MAP(PSI), \
|
/linux-6.3-rc2/include/linux/ |
A D | scmi_protocol.h | 370 PSI = 0x10, enumerator
|
/linux-6.3-rc2/Documentation/accounting/ |
A D | psi.rst | 4 PSI - Pressure Stall Information
|
/linux-6.3-rc2/arch/powerpc/boot/dts/ |
A D | fsp2.dts | 86 /* PSI and DMA */
|
/linux-6.3-rc2/drivers/gpu/drm/amd/pm/swsmu/smu13/ |
A D | smu_v13_0_4_ppt.c | 126 FEA_MAP(PSI),
|
A D | yellow_carp_ppt.c | 117 FEA_MAP(PSI),
|
/linux-6.3-rc2/Documentation/admin-guide/ |
A D | cgroup-v2.rst | 986 Writing "0" to the file will disable the cgroup PSI accounting. 987 Writing "1" to the file will re-enable the cgroup PSI accounting. 989 This control attribute is not hierarchical, so disable or enable PSI 990 accounting in a cgroup does not affect PSI accounting in descendants 993 The reason this control attribute exists is that PSI accounts stalls for 997 be used to disable PSI accounting in the non-leaf cgroups.
|
/linux-6.3-rc2/drivers/gpu/drm/amd/pm/swsmu/smu11/ |
A D | vangogh_ppt.c | 168 FEA_MAP(PSI),
|
/linux-6.3-rc2/init/ |
A D | Kconfig | 630 config PSI config 652 depends on PSI
|
/linux-6.3-rc2/ |
A D | MAINTAINERS | 16800 PRESSURE STALL INFORMATION (PSI)
|
Completed in 49 milliseconds