Searched refs:can0 (Results 1 – 25 of 154) sorted by relevance
1234567
| /linux-6.3-rc2/arch/arm64/boot/dts/renesas/ |
| A D | cat875.dtsi | 34 &can0 {
58 can0_pins: can0 {
60 function = "can0";
|
| A D | hihope-rzg2-ex.dtsi | 36 &can0 {
74 can0_pins: can0 {
76 function = "can0";
|
| A D | rzg2ul-smarc-pinfunction.dtsi | 15 can0_pins: can0 {
21 can0-stb-hog {
|
| A D | rzg2l-smarc-pinfunction.dtsi | 15 can0_pins: can0 {
21 can0-stb-hog {
|
| /linux-6.3-rc2/Documentation/ABI/testing/ |
| A D | sysfs-platform-at91 | 23 echo 0x7ff > /sys/class/net/can0/mb0_id
27 echo 0x9fffffff > /sys/class/net/can0/mb0_id
|
| /linux-6.3-rc2/Documentation/networking/device_drivers/can/freescale/ |
| A D | flexcan.rst | 52 ip link set dev can0 down
53 ethtool --set-priv-flags can0 rx-rtr {off|on}
54 ip link set dev can0 up
|
| /linux-6.3-rc2/arch/arm/boot/dts/ |
| A D | at91sam9x5_can.dtsi | 15 can0: can@f8000000 { label
38 can0 {
|
| A D | sama5d3_can.dtsi | 16 can0 {
34 can0: can@f000c000 { label
|
| A D | lan966x-pcb8291.dts | 67 can0_b_pins: can0-b-pins {
80 &can0 {
|
| A D | r9a06g032-rzn1d400-db.dts | 29 &can0 {
41 /* Please only enable can0 or can1, depending on CN10/CN11 */
|
| A D | spear320-evb.dts | 60 can0 {
62 st,function = "can0";
|
| A D | r8a7792-blanche.dts | 221 can0_pins: can0 {
223 function = "can0";
271 &can0 {
|
| A D | r8a7792-wheat.dts | 137 can0_pins: can0 {
139 function = "can0";
180 &can0 {
|
| A D | zynq-zc702.dts | 78 &can0 {
200 pinctrl_can0_default: can0-default {
202 function = "can0";
|
| A D | iwg20d-q7-common.dtsi | 168 &can0 {
256 can0_pins: can0 {
258 function = "can0";
|
| A D | r8a7745-iwg22d-sodimm.dts | 133 &can0 {
236 can0_pins: can0 {
238 function = "can0";
|
| A D | r8a7742-iwg21d-q7-dbcm-ca.dts | 73 &can0 {
132 can0_pins: can0 {
134 function = "can0";
|
| A D | at91-sam9x60_curiosity.dts | 110 &can0 {
125 status = "okay"; /* Conflict with can0. */
266 can0 {
267 pinctrl_can0_rx_tx: can0-rx-tx {
|
| A D | lpc4357-myd-lpc4357.dts | 90 can0_pins: can0-pins {
93 function = "can0";
99 function = "can0";
456 &can0 {
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/reset/ |
| A D | zynq-reset.txt | 45 256: can0 reset
47 258: can0 ref reset
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/pinctrl/ |
| A D | loongson,ls2k-pinctrl.yaml | 42 enum: [gpio, sdio, can1, can0, pwm3, pwm2, pwm1, pwm0, i2c1, i2c0,
47 enum: [gpio, sdio, can1, can0, pwm3, pwm2, pwm1, pwm0, i2c1, i2c0,
|
| /linux-6.3-rc2/drivers/pinctrl/ |
| A D | pinctrl-loongson2.c | 111 PMX_GROUP(can0, 0x0, 16),
126 SPECIFIC_GROUP(can0);
153 FUNCTION(can0),
|
| /linux-6.3-rc2/arch/powerpc/boot/dts/fsl/ |
| A D | p1010si-pre.dtsi | 53 can0 = &can0;
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/net/can/ |
| A D | atmel-can.txt | 11 can0: can@f000c000 {
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/clock/ |
| A D | zynq-7000.txt | 60 19: can0
99 "fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1",
|
Completed in 20 milliseconds
1234567