Searched refs:delay_rts_after_send (Results 1 – 15 of 15) sorted by relevance
| /linux-6.3-rc2/drivers/tty/serial/8250/ |
| A D | 8250_lpc18xx.c | 51 if (rs485->delay_rts_after_send) { in lpc18xx_rs485_config()
53 rs485_dly_reg = DIV_ROUND_UP(rs485->delay_rts_after_send in lpc18xx_rs485_config()
60 rs485->delay_rts_after_send = (rs485_dly_reg * MSEC_PER_SEC) in lpc18xx_rs485_config()
86 .delay_rts_after_send = 1,
|
| A D | 8250_pci1xxxx.c | 186 if (rs485->delay_rts_after_send) { in pci1xxxx_rs485_config()
192 rs485->delay_rts_after_send * NSEC_PER_MSEC / in pci1xxxx_rs485_config()
199 rs485->delay_rts_after_send = in pci1xxxx_rs485_config()
211 .delay_rts_after_send = 1,
|
| A D | 8250_fintek.c | 217 if (rs485->delay_rts_after_send) { in fintek_8250_rs485_config()
218 rs485->delay_rts_after_send = 1; in fintek_8250_rs485_config()
417 .delay_rts_after_send = 1,
|
| A D | 8250_omap.c | 844 rs485->delay_rts_after_send > fixed_delay_rts_after_send || in omap8250_rs485_config()
853 rs485->delay_rts_after_send = fixed_delay_rts_after_send; in omap8250_rs485_config()
|
| A D | 8250_port.c | 664 .delay_rts_after_send = 1,
1499 stop_delay += (u64)p->port.rs485.delay_rts_after_send * NSEC_PER_MSEC; in __stop_tx_rs485()
3453 mdelay(port->rs485.delay_rts_after_send); in serial8250_console_write()
|
| /linux-6.3-rc2/include/uapi/linux/ |
| A D | serial.h | 153 __u32 delay_rts_after_send; member
|
| /linux-6.3-rc2/drivers/tty/serial/ |
| A D | serial_core.c | 1334 if (!port->rs485_supported.delay_rts_after_send) { in uart_sanitize_serial_rs485_delays()
1335 if (rs485->delay_rts_after_send) { in uart_sanitize_serial_rs485_delays()
1340 rs485->delay_rts_after_send = 0; in uart_sanitize_serial_rs485_delays()
1341 } else if (rs485->delay_rts_after_send > RS485_MAX_RTS_DELAY) { in uart_sanitize_serial_rs485_delays()
1342 rs485->delay_rts_after_send = RS485_MAX_RTS_DELAY; in uart_sanitize_serial_rs485_delays()
1345 port->name, port->line, rs485->delay_rts_after_send); in uart_sanitize_serial_rs485_delays()
3423 rs485conf->delay_rts_after_send = rs485_delay[1]; in uart_get_rs485_mode()
3426 rs485conf->delay_rts_after_send = 0; in uart_get_rs485_mode()
3483 (offsetof(struct serial_rs485, delay_rts_after_send) + sizeof(__u32)));
|
| A D | max310x.c | 1019 one->port.rs485.delay_rts_after_send; in max310x_rs_proc()
1041 (rs485->delay_rts_after_send > 0x0f)) in max310x_rs485_config()
1070 clamp(port->rs485.delay_rts_after_send, 0U, 15U); in max310x_startup()
1259 .delay_rts_after_send = 1,
|
| A D | stm32-usart.c | 249 rs485conf->delay_rts_after_send, in stm32_usart_config_rs485()
284 rs485conf->delay_rts_after_send = 0; in stm32_usart_init_rs485()
1265 rs485conf->delay_rts_after_send, in stm32_usart_set_termios()
1446 .delay_rts_after_send = 1,
|
| A D | omap-serial.c | 304 if (port->rs485.delay_rts_after_send > 0) in serial_omap_stop_tx()
306 port->rs485.delay_rts_after_send); in serial_omap_stop_tx()
1545 .delay_rts_after_send = 1,
|
| A D | atmel_serial.c | 313 rs485conf->delay_rts_after_send); in atmel_config_rs485()
480 port->rs485.delay_rts_after_send); in atmel_set_mctrl()
2226 port->rs485.delay_rts_after_send); in atmel_set_termios()
2528 .delay_rts_after_send = 1,
|
| A D | sc16is7xx.c | 1139 if (rs485->delay_rts_after_send) in sc16is7xx_config_rs485()
1356 .delay_rts_after_send = 1, /* Not supported but keep returning -EINVAL */
|
| A D | amba-pl011.c | 1309 if (port->rs485.delay_rts_after_send) in pl011_rs485_tx_stop()
1310 mdelay(port->rs485.delay_rts_after_send); in pl011_rs485_tx_stop()
2783 .delay_rts_after_send = 1,
|
| A D | imx.c | 443 if (port->rs485.delay_rts_after_send > 0) { in imx_uart_stop_tx()
445 port->rs485.delay_rts_after_send); in imx_uart_stop_tx()
2234 .delay_rts_after_send = 1,
|
| /linux-6.3-rc2/Documentation/driver-api/serial/ |
| A D | serial-rs485.rst | 91 rs485conf.delay_rts_after_send = ...;
|
Completed in 49 milliseconds