| /linux-6.3-rc2/Documentation/devicetree/bindings/regulator/ |
| A D | tps65132-regulator.txt | 17 -active-discharge-gpios: (active high, output) Some configurations use delay mechanisms
19 the enable signal goes low. This GPIO is used to actively discharge
20 the delay mechanism. Requires specification of ti,active-discharge-time-us
21 -ti,active-discharge-time-us: how long the active discharge gpio should be
22 asserted for during active discharge, in microseconds.
43 regulator-active-discharge = <0>;
|
| A D | ti,tps62360.yaml | 49 ti,enable-vout-discharge:
50 description: Enable output discharge.
94 ti,enable-vout-discharge;
|
| A D | maxim,max8973.yaml | 61 maxim,enable-active-discharge:
63 description: Eable active discharge.
135 maxim,enable-active-discharge;
|
| A D | qcom-labibb-regulator.yaml | 54 qcom,discharge-resistor-kohms:
|
| A D | regulator.yaml | 203 regulator-active-discharge:
205 tristate, enable/disable active discharge of regulators. The values are:
206 0: Disable active discharge.
207 1: Enable active discharge.
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/power/supply/ |
| A D | dlg,da9150-fuel-gauge.yaml | 27 description: Battery discharge level (%) where warning event raised.
34 Battery discharge level (%) where critical event raised.
|
| A D | x-powers,axp20x-battery-power-supply.yaml | 10 The supported devices can read the battery voltage, charge and discharge
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/display/ |
| A D | repaper.txt | 10 - discharge-gpios: Discharge control
47 discharge-gpios = <&gpio 15 0>;
|
| /linux-6.3-rc2/drivers/gpu/drm/tiny/ |
| A D | repaper.c | 73 struct gpio_desc *discharge; member
619 gpiod_set_value_cansleep(epd->discharge, 1); in power_off()
621 gpiod_set_value_cansleep(epd->discharge, 0); in power_off()
651 gpiod_set_value_cansleep(epd->discharge, 0); in repaper_pipe_enable()
989 epd->discharge = devm_gpiod_get(dev, "discharge", GPIOD_OUT_LOW); in repaper_probe()
990 if (IS_ERR(epd->discharge)) { in repaper_probe()
991 ret = PTR_ERR(epd->discharge); in repaper_probe()
|
| /linux-6.3-rc2/include/sound/ |
| A D | wm2200.h | 39 unsigned int discharge:1; /** Actively discharge */ member
|
| A D | da7218.h | 80 bool discharge; member
|
| /linux-6.3-rc2/arch/arm/boot/dts/ |
| A D | stm32mp15xx-osd32.dtsi | 177 regulator-active-discharge = <1>;
183 regulator-active-discharge = <1>;
|
| A D | stm32mp15xx-dhcor-som.dtsi | 194 regulator-active-discharge = <1>;
200 regulator-active-discharge = <1>;
|
| A D | stm32mp157a-stinger96.dtsi | 219 regulator-active-discharge = <1>;
225 regulator-active-discharge = <1>;
|
| A D | tegra30-asus-nexus7-grouper-ti-pmic.dtsi | 138 ti,enable-vout-discharge;
|
| A D | stm32mp157c-odyssey-som.dtsi | 213 regulator-active-discharge = <1>;
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/sound/ |
| A D | da7218.txt | 64 - dlg,discharge : Boolean flag, auto discharge of Mic Bias on jack removal
|
| /linux-6.3-rc2/arch/arm/mach-pxa/ |
| A D | sharpsl_pm.h | 18 void (*discharge)(int); member
|
| A D | spitz_pm.c | 198 .discharge = spitz_discharge,
|
| A D | sharpsl_pm.c | 522 sharpsl_pm.machinfo->discharge(1); in sharpsl_check_battery_voltage()
537 sharpsl_pm.machinfo->discharge(0); in sharpsl_check_battery_voltage()
|
| /linux-6.3-rc2/include/linux/mfd/arizona/ |
| A D | pdata.h | 61 unsigned int discharge:1; /** Actively discharge */ member
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/display/panel/ |
| A D | samsung,s6d27a1.yaml | 26 description: provides an optional ESD (electrostatic discharge)
|
| A D | samsung,lms380kf01.yaml | 27 description: provides an optional ESD (electrostatic discharge)
|
| /linux-6.3-rc2/arch/arm64/boot/dts/qcom/ |
| A D | msm8916-huawei-g7.dts | 150 regulator-active-discharge = <1>;
158 regulator-active-discharge = <1>;
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/mfd/ |
| A D | actions,atc260x.yaml | 69 regulator-active-discharge: true
|