Searched refs:oversampling (Results 1 – 18 of 18) sorted by relevance
| /linux-6.3-rc2/Documentation/devicetree/bindings/iio/adc/ |
| A D | ti,tsc2046.yaml | 56 oversampling-ratio: true
91 oversampling-ratio = <5>;
99 oversampling-ratio = <5>;
104 oversampling-ratio = <5>;
109 oversampling-ratio = <5>;
|
| A D | adi,ad7606.yaml | 81 adi,oversampling-ratio-gpios:
91 It is enabled when all three oversampling mode pins are connected to
93 adi,oversampling-ratio-gpios property is defined, then the driver will set the
94 oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
134 adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>,
|
| A D | adc.yaml | 46 oversampling-ratio:
|
| /linux-6.3-rc2/arch/arm/boot/dts/ |
| A D | imx6qdl-skov-cpu-revc.dtsi | 39 oversampling-ratio = <5>;
45 oversampling-ratio = <5>;
51 oversampling-ratio = <5>;
57 oversampling-ratio = <5>;
|
| A D | imx6dl-plym2m.dts | 210 oversampling-ratio = <5>;
216 oversampling-ratio = <5>;
222 oversampling-ratio = <5>;
228 oversampling-ratio = <5>;
234 oversampling-ratio = <5>;
240 oversampling-ratio = <5>;
248 oversampling-ratio = <5>;
|
| A D | imx6dl-victgo.dts | 158 oversampling-ratio = <5>;
164 oversampling-ratio = <5>;
170 oversampling-ratio = <5>;
176 oversampling-ratio = <5>;
|
| A D | imx6dl-prtvt7.dts | 358 oversampling-ratio = <5>;
364 oversampling-ratio = <5>;
370 oversampling-ratio = <5>;
376 oversampling-ratio = <5>;
|
| /linux-6.3-rc2/Documentation/misc-devices/ |
| A D | oxsemi-tornado.rst | 14 value from 1 to 65535. Finally a programmable oversampling rate is used
19 By default the oversampling rate is set to 16 and the clock prescaler is
26 The oversampling rate is programmed with the TCR register and the clock
44 from the requested rate (d), and the values of the oversampling rate
93 used by encoding the values for, the prescaler, the oversampling rate
109 oversampling rate to 16 and prescaler values below 1 in CPR2/CPR are
114 the oversampling rate and the clock divisor of 62.500, 16 and 1250
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/media/i2c/ |
| A D | adv7343.txt | 16 - adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows
18 oversampling to be switched off.
|
| /linux-6.3-rc2/drivers/iio/adc/ |
| A D | ad7606.h | 96 unsigned int oversampling; member
|
| A D | ad7606.c | 195 *val = st->oversampling; in ad7606_read_raw()
289 st->oversampling = st->oversampling_avail[i]; in ad7606_write_raw()
581 st->oversampling = 1; in ad7606_probe()
|
| /linux-6.3-rc2/drivers/spi/ |
| A D | spi-geni-qcom.c | 92 unsigned int oversampling; member
114 speed_hz * mas->oversampling, in get_spi_clk_cfg()
122 *clk_div = DIV_ROUND_UP(sclk_freq, mas->oversampling * speed_hz); in get_spi_clk_cfg()
123 actual_hz = sclk_freq / (mas->oversampling * *clk_div); in get_spi_clk_cfg()
634 mas->oversampling = 2; in spi_geni_init()
636 mas->oversampling = 1; in spi_geni_init()
|
| /linux-6.3-rc2/drivers/tty/serial/ |
| A D | amba-pl011.c | 112 bool oversampling; member
133 .oversampling = false,
148 .oversampling = false,
164 .oversampling = false,
211 .oversampling = true,
2053 if (uap->vendor->oversampling) in pl011_set_termios()
2139 if (uap->vendor->oversampling) { in pl011_set_termios()
2152 if (uap->vendor->oversampling) { in pl011_set_termios()
2391 if (uap->vendor->oversampling) { in pl011_console_get_options()
|
| A D | stm32-usart.c | 1092 u32 usartdiv, mantissa, fraction, oversampling; in stm32_usart_set_termios() local
1212 oversampling = 8; in stm32_usart_set_termios()
1216 oversampling = 16; in stm32_usart_set_termios()
1221 mantissa = (usartdiv / oversampling) << USART_BRR_DIV_M_SHIFT; in stm32_usart_set_termios()
1222 fraction = usartdiv % oversampling; in stm32_usart_set_termios()
|
| /linux-6.3-rc2/Documentation/sound/soc/ |
| A D | overview.rst | 24 power via changing codec oversampling rates, bias currents, etc.
|
| /linux-6.3-rc2/arch/arm64/boot/dts/freescale/ |
| A D | imx8mp-dhcom-som.dtsi | 423 * which with 16x oversampling yields 5 Mbdps baud base,
|
| /linux-6.3-rc2/drivers/tty/serial/8250/ |
| A D | Kconfig | 370 Uses 8 times oversampling (compared to 16 times for 16650)
|
| /linux-6.3-rc2/Documentation/ABI/testing/ |
| A D | sysfs-bus-iio | 132 Hardware dependent ADC oversampling. Controls the sampling ratio
139 Hardware dependent values supported by the oversampling filter.
|
Completed in 35 milliseconds