| /linux-6.3-rc2/Documentation/devicetree/bindings/arm/marvell/ |
| A D | kirkwood.txt | 12 cpus/cpu@0 with three clocks, "cpu_clk", "ddrclk" and "powersave",
13 where the "powersave" clock is a gating clock used to switch the CPU
26 clock-names = "cpu_clk", "ddrclk", "powersave";
|
| /linux-6.3-rc2/tools/testing/selftests/intel_pstate/ |
| A D | run.sh | 98 cpupower frequency-set -g powersave --max=${freq}MHz >& /dev/null
102 [ $EVALUATE_ONLY -eq 0 ] && cpupower frequency-set -g powersave --max=${max_freq}MHz >& /dev/null
|
| /linux-6.3-rc2/arch/powerpc/platforms/pasemi/ |
| A D | Makefile | 2 obj-y += setup.o pci.o time.o idle.o powersave.o iommu.o dma_lib.o misc.o
|
| /linux-6.3-rc2/Documentation/sound/designs/ |
| A D | index.rst | 14 powersave
|
| /linux-6.3-rc2/net/mac80211/ |
| A D | pm.c | 109 sdata->u.mgd.powersave && in __ieee80211_suspend()
|
| A D | Kconfig | 188 bool "Verbose powersave mode debugging"
261 bool "Verbose mesh powersave debugging"
266 powersave debugging messages (when mac80211 is taking part in a
|
| A D | ieee80211_i.h | 488 bool powersave; /* powersave requested for this iface */ member
2286 bool powersave);
|
| A D | mlme.c | 1059 else if (sdata->u.mgd.powersave) in ieee80211_assoc_link_elems()
1617 bool powersave) in ieee80211_send_nullfunc() argument
1630 if (powersave) in ieee80211_send_nullfunc()
2230 if (!mgd->powersave) in ieee80211_powersave_allowed()
5744 } else if (!local->pspolling && sdata->u.mgd.powersave) { in ieee80211_rx_mgmt_beacon()
6551 ifmgd->powersave = sdata->wdev.ps; in ieee80211_sta_setup_sdata()
7102 if (sdata->u.mgd.powersave) in ieee80211_setup_assoc_link()
|
| A D | cfg.c | 3132 if (tdls_peer_found || !sdata->u.mgd.powersave) in __ieee80211_request_smps_mgd()
3162 if (enabled == sdata->u.mgd.powersave && in ieee80211_set_power_mgmt()
3166 sdata->u.mgd.powersave = enabled; in ieee80211_set_power_mgmt()
|
| A D | rx.c | 4461 if (!sdata->u.mgd.powersave) in ieee80211_check_fast_rx()
|
| /linux-6.3-rc2/drivers/cpufreq/ |
| A D | Kconfig | 56 bool "powersave"
59 Use the CPUFreq governor 'powersave' as default. This sets
122 tristate "'powersave' governor"
|
| A D | Kconfig.x86 | 164 tristate "AMD frequency sensitivity feedback powersave bias"
167 This adds AMD-specific powersave bias function to the ondemand
|
| /linux-6.3-rc2/Documentation/networking/ |
| A D | mac80211-auth-assoc-deauth.txt | 92 mac80211->driver: turn off powersave
|
| /linux-6.3-rc2/net/wireless/ |
| A D | Kconfig | 163 bool "enable powersave by default"
166 This option enables powersave mode by default.
|
| /linux-6.3-rc2/drivers/net/wireless/ath/ath9k/ |
| A D | channel.c | 1102 bool powersave) in ath_chanctx_send_vif_ps_frame() argument
1121 if (powersave) in ath_chanctx_send_vif_ps_frame()
1148 ath_chanctx_send_ps_frame(struct ath_softc *sc, bool powersave) in ath_chanctx_send_ps_frame() argument
1155 if (ath_chanctx_send_vif_ps_frame(sc, avp, powersave)) in ath_chanctx_send_ps_frame()
|
| /linux-6.3-rc2/Documentation/admin-guide/pm/ |
| A D | intel_pstate.rst | 83 For example, the ``powersave`` P-state selection algorithm provided by
84 ``intel_pstate`` is not a counterpart of the generic ``powersave`` governor
88 active mode: ``powersave`` and ``performance``. The way they both operate
134 HWP + ``powersave``
157 ``powersave`` or ``performance``, depending on the ``scaling_governor`` policy
176 ``powersave``
619 affects decisions made by the scaling governors, except for ``powersave`` and
|
| A D | cpufreq.rst | 367 ``powersave``
374 ``powersave`` and whenever the ``scaling_max_freq`` or ``scaling_min_freq``
517 for the AMD frequency sensitivity powersave bias driver
521 If the AMD frequency sensitivity powersave bias driver is not loaded,
529 If the AMD frequency sensitivity powersave bias driver is loaded, the
545 the ``powersave_bias`` value, the sensitivity powersave bias driver
|
| A D | amd-pstate.rst | 385 available cpufreq governors: ondemand conservative powersave userspace performance schedutil
|
| /linux-6.3-rc2/tools/power/cpupower/bench/ |
| A D | README-BENCH | 29 powersave module.
|
| /linux-6.3-rc2/arch/arm/boot/dts/ |
| A D | kirkwood.dtsi | 22 clock-names = "cpu_clk", "ddrclk", "powersave";
|
| /linux-6.3-rc2/Documentation/livepatch/ |
| A D | shadow-vars.rst | 101 ("mac80211: fix AP powersave TX vs. wakeup race"), which added a
|
| /linux-6.3-rc2/sound/drivers/ |
| A D | Kconfig | 234 See Documentation/sound/designs/powersave.rst for more details.
|
| /linux-6.3-rc2/Documentation/admin-guide/sysctl/ |
| A D | kernel.rst | 971 powersave-nap (PPC only)
1204 range of [0:600]. This could happen for instance if a powersave mode will
|
| /linux-6.3-rc2/Documentation/sound/ |
| A D | alsa-configuration.rst | 1083 mode. See powersave.rst for details.
|
| /linux-6.3-rc2/Documentation/admin-guide/ |
| A D | kernel-parameters.txt | 4467 powersave=off [PPC] This option disables power saving features.
|