| /linux-6.3-rc2/Documentation/userspace-api/ |
| A D | sysfs-platform_profile.rst | 16 API for selecting the platform profile of these automatic mechanisms.
18 Note that this API is only for selecting the platform profile, it is
23 Specifically when selecting a high performance profile the actual achieved
|
| /linux-6.3-rc2/drivers/scsi/ |
| A D | NCR5380.c | 619 !hostdata->selecting) { in maybe_release_dma_irq()
989 hostdata->selecting = cmd; in NCR5380_select()
1018 if (!hostdata->selecting) { in NCR5380_select()
1067 if (!hostdata->selecting) { in NCR5380_select()
1152 if (!hostdata->selecting) in NCR5380_select()
1189 if (!hostdata->selecting) { in NCR5380_select()
1225 if (!hostdata->selecting) in NCR5380_select()
1227 hostdata->selecting = NULL; in NCR5380_select()
2270 hostdata->selecting = NULL; in NCR5380_abort()
2341 if (hostdata->selecting) { in bus_reset_cleanup()
[all …]
|
| A D | wd33c93.c | 421 if (hostdata->selecting || hostdata->connected) { in DEF_SCSI_QCMD()
543 hostdata->selecting = cmd; in DEF_SCSI_QCMD()
795 cmd = (struct scsi_cmnd *) hostdata->selecting; /* get a valid cmd */ in wd33c93_intr()
796 hostdata->selecting = NULL; in wd33c93_intr()
828 (struct scsi_cmnd *) hostdata->selecting; in wd33c93_intr()
829 hostdata->selecting = NULL; in wd33c93_intr()
1291 if (hostdata->selecting) { in wd33c93_intr()
1292 cmd = (struct scsi_cmnd *) hostdata->selecting; in wd33c93_intr()
1293 hostdata->selecting = NULL; in wd33c93_intr()
1533 hostdata->selecting = NULL; in wd33c93_host_reset()
[all …]
|
| A D | mac53c94.c | 38 selecting, enumerator
175 state->phase = selecting; in mac53c94_start()
247 case selecting: in mac53c94_interrupt()
|
| A D | wd33c93.h | 227 volatile struct scsi_cmnd *selecting; /* trying to select this command */ member
|
| A D | NCR5380.h | 217 struct scsi_cmnd *selecting; /* Cmnd to be connected */ member
|
| /linux-6.3-rc2/Documentation/leds/ |
| A D | ledtrig-usbport.rst | 9 It requires selecting USB ports that should be observed. All available ones are
13 Please note that this trigger allows selecting multiple USB ports for a single
|
| /linux-6.3-rc2/Documentation/admin-guide/hw-vuln/ |
| A D | index.rst | 6 possible mitigations along with guidance for selecting mitigations if they
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/pinctrl/ |
| A D | actions,s900-pinctrl.txt | 57 These pins are used for selecting the pull control and schmitt
91 group. These pin groups are used for selecting the pinmux
113 These pin groups are used for selecting the drive strength
126 These pin groups are used for selecting the slew rate
|
| A D | actions,s700-pinctrl.txt | 57 These pins are used for selecting the pull control and schmitt
85 group. These pin groups are used for selecting the pinmux
103 These pin groups are used for selecting the drive strength
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/clock/ |
| A D | gpio-mux-clock.yaml | 25 description: GPIO reference for selecting the parent clock.
|
| /linux-6.3-rc2/Documentation/networking/ |
| A D | secid.rst | 10 the label of the flow. This label of the flow is currently used in selecting
|
| A D | tc-queue-filters.rst | 22 Likewise, on the receive side, the two filters for selecting set of
|
| /linux-6.3-rc2/fs/squashfs/ |
| A D | Kconfig | 176 file systems will be readable without selecting this option.
191 file systems will be readable without selecting this option.
206 file systems will be readable without selecting this option.
220 file systems will be readable without selecting this option.
|
| /linux-6.3-rc2/Documentation/userspace-api/media/dvb/ |
| A D | fe-dishnetwork-send-legacy-cmd.rst | 38 It provides a non-standard method for selecting Diseqc voltage on the
|
| A D | fe-set-tone.rst | 44 capability of selecting the band. So, it is recommended that applications
|
| A D | frontend.rst | 43 control the antenna subsystem, selecting the polarization and choosing
|
| /linux-6.3-rc2/Documentation/userspace-api/media/v4l/ |
| A D | common.rst | 12 - Changing device properties, selecting a video and audio input, video
|
| A D | ext-ctrls-image-process.rst | 40 The configuration of the frame rate is performed by selecting the desired
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/input/touchscreen/ |
| A D | bu21013.txt | 6 - reset-gpios : GPIO pin enabling (selecting) chip (CS)
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/sound/ |
| A D | adi,adau1701.txt | 19 - adi,pin-config: An array of 12 numerical values selecting one of the
|
| /linux-6.3-rc2/security/selinux/ |
| A D | Kconfig | 40 NOTE: selecting this option will disable the '__ro_after_init'
105 chain lengths are high (e.g. > 20) then selecting a higher value here
|
| /linux-6.3-rc2/drivers/media/usb/pwc/ |
| A D | Kconfig | 28 The built-in microphone is enabled by selecting USB Audio support.
|
| /linux-6.3-rc2/fs/crypto/ |
| A D | Kconfig | 18 # whereas selecting them from FS_ENCRYPTION would force them to be built-in.
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/leds/ |
| A D | skyworks,aat1290.yaml | 16 respectively. In order to add a capability of selecting the strobe signal
|