| /linux-6.3-rc2/Documentation/devicetree/bindings/iio/adc/ |
| A D | qcom,spmi-iadc.yaml | 15 through an external resistor (channel 1) or internal (built-in) resistor
16 (channel 0). When using an external resistor it is to be described by
17 qcom,external-resistor-micro-ohms property.
31 qcom,external-resistor-micro-ohms:
33 Sensor resistor value. If not defined value of 10000 micro Ohms
60 qcom,external-resistor-micro-ohms = <10000>;
|
| A D | maxim,max9611.yaml | 25 shunt-resistor-micro-ohms:
27 Value in micro Ohms of the shunt resistor connected between the RS+ and
36 - shunt-resistor-micro-ohms
47 shunt-resistor-micro-ohms = <5000>;
|
| A D | ti,lmp92064.yaml | 34 shunt-resistor-micro-ohms:
36 Value of the shunt resistor (in µΩ) connected between INCP and INCN,
46 - shunt-resistor-micro-ohms
66 shunt-resistor-micro-ohms = <15000>;
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/iio/dac/ |
| A D | adi,ad5755.yaml | 28 adi,ext-dc-dc-compenstation-resistor:
31 Set if the hardware have an external resistor and thereby bypasses
32 the internal compensation resistor.
90 adi,ext-current-sense-resistor:
93 Set if the hardware has an external current sense resistor
146 adi,ext-current-sense-resistor;
152 adi,ext-current-sense-resistor;
158 adi,ext-current-sense-resistor;
164 adi,ext-current-sense-resistor;
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/hwmon/ |
| A D | ntc-thermistor.yaml | 20 pull-up resistor or/and a pull-down resistor and a fixed voltage like this:
26 | | Pull-up resistor
40 | | Pull-down resistor | Measured voltage (mv)
52 positive voltage and we get the thermistor on top of a pull-down resistor
53 and we take the measure between the thermistor and the pull-down resistor.
56 connected to ground and we get the thermistor under the pull-up resistor
57 and we take the measure between the pull-up resistor and the thermistor.
112 a pull-up and/or a pull-down resistor. See the description above for
120 description: IIO ADC channel to read the voltage over the resistor. Must
|
| A D | adi,ltc2945.yaml | 25 shunt-resistor-micro-ohms:
27 Shunt resistor value in micro-Ohms
45 /* 10 milli-Ohm shunt resistor */
46 shunt-resistor-micro-ohms = <10000>;
|
| A D | adi,ltc2992.yaml | 46 shunt-resistor-micro-ohms:
48 The value of curent sense resistor in microohms.
71 shunt-resistor-micro-ohms = <10000>;
76 shunt-resistor-micro-ohms = <10000>;
|
| A D | lltc,ltc4151.yaml | 19 shunt-resistor-micro-ohms:
21 Shunt resistor value in micro-Ohms
39 shunt-resistor-micro-ohms = <1500>;
|
| A D | adi,adm1177.yaml | 28 shunt-resistor-micro-ohms:
30 The value of curent sense resistor in microohms. If not provided,
37 based on shunt-resistor-micro-ohms.
62 shunt-resistor-micro-ohms = <50000>; /* 50 mOhm */
|
| A D | ina3221.txt | 31 - shunt-resistor-micro-ohms: Shunt resistor value in micro-Ohm
47 shunt-resistor-micro-ohms = <5000>;
52 shunt-resistor-micro-ohms = <5000>;
|
| A D | ti,tps23861.yaml | 28 shunt-resistor-micro-ohms:
29 description: The value of curent sense resistor in microohms.
49 shunt-resistor-micro-ohms = <255000>;
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/power/supply/ |
| A D | lltc,ltc294x.yaml | 33 lltc,resistor-sense:
36 Sense resistor value in milli-ohms.
37 Can be negative value when the battery has been connected to the wrong end of the resistor.
50 - lltc,resistor-sense
63 lltc,resistor-sense = <15>;
|
| /linux-6.3-rc2/Documentation/hwmon/ |
| A D | ltc2990.rst | 29 measure current through a series resistor, or a temperature with an external
55 curr1_input Current in mA across V1-V2 assuming a 1mOhm sense resistor
56 curr2_input Current in mA across V3-V4 assuming a 1mOhm sense resistor
61 sense resistor. Divide the reported value by the actual sense resistor value
|
| A D | ltc4260.rst | 46 value of the divider resistor against the measured voltage and R2 is the value
47 of the divider resistor against Ground.
50 Current Sense register. The reported value assumes that a 1 mOhm sense resistor
51 is installed. If a different sense resistor is installed, calculate the real
52 current by dividing the reported value by the sense resistor value in mOhm.
|
| A D | ltc4261.rst | 46 value of the divider resistor against the measured voltage and R2 is the value
47 of the divider resistor against Ground.
50 Current Sense register. The reported value assumes that a 1 mOhm sense resistor
51 is installed. If a different sense resistor is installed, calculate the real
52 current by dividing the reported value by the sense resistor value in mOhm.
|
| A D | ltc2945.rst | 46 value of the divider resistor against the measured voltage and R2 is the value
47 of the divider resistor against Ground.
50 Current Sense register. The reported value assumes that a 1 mOhm sense resistor
51 is installed. If a different sense resistor is installed, calculate the real
52 current by dividing the reported value by the sense resistor value in mOhm.
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/iio/afe/ |
| A D | current-sense-amplifier.yaml | 15 through the sense resistor, not the voltage output. This binding
27 sense-resistor-micro-ohms:
41 - sense-resistor-micro-ohms
51 sense-resistor-micro-ohms = <20000>;
|
| /linux-6.3-rc2/arch/arm/boot/dts/ |
| A D | am3874-iceboard.dts | 156 ina230@40 { compatible = "ti,ina230"; reg = <0x40>; shunt-resistor = <5000>; };
157 ina230@41 { compatible = "ti,ina230"; reg = <0x41>; shunt-resistor = <5000>; };
158 ina230@42 { compatible = "ti,ina230"; reg = <0x42>; shunt-resistor = <5000>; };
160 ina230@44 { compatible = "ti,ina230"; reg = <0x44>; shunt-resistor = <5000>; };
161 ina230@45 { compatible = "ti,ina230"; reg = <0x45>; shunt-resistor = <5000>; };
162 ina230@46 { compatible = "ti,ina230"; reg = <0x46>; shunt-resistor = <5000>; };
164 ina230@47 { compatible = "ti,ina230"; reg = <0x47>; shunt-resistor = <5500>; };
165 ina230@48 { compatible = "ti,ina230"; reg = <0x48>; shunt-resistor = <2360>; };
170 ina230@4d { compatible = "ti,ina230"; reg = <0x4d>; shunt-resistor = <770>; };
171 ina230@4e { compatible = "ti,ina230"; reg = <0x4e>; shunt-resistor = <770>; };
[all …]
|
| A D | exynos5422-odroidxu3.dts | 31 shunt-resistor = <10000>;
38 shunt-resistor = <10000>;
45 shunt-resistor = <10000>;
52 shunt-resistor = <10000>;
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/phy/ |
| A D | mxs-usb-phy.txt | 19 high-speed trimming resistor connected in parallel with the 45 ohm resistor
22 high-speed trimming resistor connected in parallel with the 45 ohm resistor
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/rtc/ |
| A D | dallas,ds1390.txt | 8 - trickle-resistor-ohms : Selected resistor for trickle charger
16 trickle-resistor-ohms = <250>;
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/iio/potentiostat/ |
| A D | ti,lmp91000.yaml | 29 ti,external-tia-resistor:
33 signal that an external resistor value is being used.
39 Internal resistor for the transimpedance amplifier.
45 Internal resistor load applied to the gas sensor.
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/leds/ |
| A D | richtek,rt8515.yaml | 33 description: The resistance value of the RFS resistor. This
35 for the property flash-max-microamp to work, the RFS resistor
42 description: The resistance value of the RTS resistor. This
44 for the property torch-max-microamp to work, the RTS resistor
59 is hardwired to the component using the RFS resistor to
71 is hardwired to the component using the RTS resistor to
|
| /linux-6.3-rc2/Documentation/devicetree/bindings/sound/ |
| A D | sgtl5000.yaml | 42 micbias-resistor-k-ohms:
43 description: The bias resistor to be used in kOhms. The resistor can take
45 mentioned or if the value is unknown, then micbias resistor is set to
107 micbias-resistor-k-ohms = <2>;
|
| /linux-6.3-rc2/arch/arm64/boot/dts/xilinx/ |
| A D | zynqmp-zcu106-revA.dts | 298 shunt-resistor = <5000>;
305 shunt-resistor = <5000>;
312 shunt-resistor = <5000>;
319 shunt-resistor = <5000>;
326 shunt-resistor = <5000>;
333 shunt-resistor = <5000>;
340 shunt-resistor = <5000>;
347 shunt-resistor = <5000>;
354 shunt-resistor = <5000>;
361 shunt-resistor = <5000>;
[all …]
|