1TI SoC Ethernet Switch Controller Device Tree Bindings
2------------------------------------------------------
3
4Required properties:
5- compatible		: Should be one of the below:-
6			  "ti,cpsw" for backward compatible
7			  "ti,am335x-cpsw" for AM335x controllers
8			  "ti,am4372-cpsw" for AM437x controllers
9			  "ti,dra7-cpsw" for DRA7x controllers
10- reg			: physical base address and size of the cpsw
11			  registers map
12- interrupts		: property with a value describing the interrupt
13			  number
14- cpdma_channels 	: Specifies number of channels in CPDMA
15- ale_entries		: Specifies No of entries ALE can hold
16- bd_ram_size		: Specifies internal descriptor RAM size
17- mac_control		: Specifies Default MAC control register content
18			  for the specific platform
19- slaves		: Specifies number for slaves
20- active_slave		: Specifies the slave to use for time stamping,
21			  ethtool and SIOCGMIIPHY
22- cpsw-phy-sel		: Specifies the phandle to the CPSW phy mode selection
23			  device. See also cpsw-phy-sel.txt for its binding.
24			  Note that in legacy cases cpsw-phy-sel may be
25			  a child device instead of a phandle
26			  (DEPRECATED, use phys property instead).
27
28Optional properties:
29- ti,hwmods		: Must be "cpgmac0"
30- dual_emac		: Specifies Switch to act as Dual EMAC
31- syscon		: Phandle to the system control device node, which is
32			  the control module device of the am33x
33- mode-gpios		: Should be added if one/multiple gpio lines are
34			  required to be driven so that cpsw data lines
35			  can be connected to the phy via selective mux.
36			  For example in dra72x-evm, pcf gpio has to be
37			  driven low so that cpsw slave 0 and phy data
38			  lines are connected via mux.
39- cpts_clock_mult	: Numerator to convert input clock ticks into nanoseconds
40- cpts_clock_shift	: Denominator to convert input clock ticks into nanoseconds
41			  Mult and shift will be calculated basing on CPTS
42			  rftclk frequency if both cpts_clock_shift and
43			  cpts_clock_mult properties are not provided.
44
45Slave Properties:
46Required properties:
47- phy-mode		: See ethernet.txt file in the same directory
48- phys			: phandle on phy-gmii-sel PHY (see phy/ti-phy-gmii-sel.txt)
49
50Optional properties:
51- dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
52- phy_id		: Specifies slave phy id (deprecated, use phy-handle)
53- phy-handle		: See ethernet.txt file in the same directory
54
55The MAC address will be determined using the optional properties
56defined in ethernet.txt.
57
58Slave sub-nodes:
59- fixed-link		: See fixed-link.txt file in the same directory
60
61Note: Exactly one of phy_id, phy-handle, or fixed-link must be specified.
62
63Note: "ti,hwmods" field is used to fetch the base address and irq
64resources from TI, omap hwmod data base during device registration.
65Future plan is to migrate hwmod data base contents into device tree
66blob so that, all the required data will be used from device tree dts
67file.
68
69Examples:
70
71	mac: ethernet@4a100000 {
72		compatible = "ti,cpsw";
73		reg = <0x4A100000 0x1000>;
74		interrupts = <55 0x4>;
75		interrupt-parent = <&intc>;
76		cpdma_channels = <8>;
77		ale_entries = <1024>;
78		bd_ram_size = <0x2000>;
79		rx_descs = <64>;
80		mac_control = <0x20>;
81		slaves = <2>;
82		active_slave = <0>;
83		cpts_clock_mult = <0x80000000>;
84		cpts_clock_shift = <29>;
85		syscon = <&cm>;
86		cpsw-phy-sel = <&phy_sel>;
87		cpsw_emac0: slave@0 {
88			phy_id = <&davinci_mdio>, <0>;
89			phy-mode = "rgmii-txid";
90			/* Filled in by U-Boot */
91			mac-address = [ 00 00 00 00 00 00 ];
92			phys = <&phy_gmii_sel 1 0>;
93		};
94		cpsw_emac1: slave@1 {
95			phy_id = <&davinci_mdio>, <1>;
96			phy-mode = "rgmii-txid";
97			/* Filled in by U-Boot */
98			mac-address = [ 00 00 00 00 00 00 ];
99			phys = <&phy_gmii_sel 2 0>;
100		};
101	};
102
103(or)
104	mac: ethernet@4a100000 {
105		compatible = "ti,cpsw";
106		ti,hwmods = "cpgmac0";
107		cpdma_channels = <8>;
108		ale_entries = <1024>;
109		bd_ram_size = <0x2000>;
110		rx_descs = <64>;
111		mac_control = <0x20>;
112		slaves = <2>;
113		active_slave = <0>;
114		cpts_clock_mult = <0x80000000>;
115		cpts_clock_shift = <29>;
116		syscon = <&cm>;
117		cpsw-phy-sel = <&phy_sel>;
118		cpsw_emac0: slave@0 {
119			phy_id = <&davinci_mdio>, <0>;
120			phy-mode = "rgmii-txid";
121			/* Filled in by U-Boot */
122			mac-address = [ 00 00 00 00 00 00 ];
123			phys = <&phy_gmii_sel 1 0>;
124		};
125		cpsw_emac1: slave@1 {
126			phy_id = <&davinci_mdio>, <1>;
127			phy-mode = "rgmii-txid";
128			/* Filled in by U-Boot */
129			mac-address = [ 00 00 00 00 00 00 ];
130			phys = <&phy_gmii_sel 2 0>;
131		};
132	};
133