1// SPDX-License-Identifier: GPL-2.0
2#include <dt-bindings/iio/qcom,spmi-vadc.h>
3#include <dt-bindings/interrupt-controller/irq.h>
4#include <dt-bindings/spmi/spmi.h>
5
6&spmi_bus {
7
8	pm8941_0: pm8941@0 {
9		compatible = "qcom,pm8941", "qcom,spmi-pmic";
10		reg = <0x0 SPMI_USID>;
11		#address-cells = <1>;
12		#size-cells = <0>;
13
14		rtc@6000 {
15			compatible = "qcom,pm8941-rtc";
16			reg = <0x6000>,
17			      <0x6100>;
18			reg-names = "rtc", "alarm";
19			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
20		};
21
22		pwrkey@800 {
23			compatible = "qcom,pm8941-pwrkey";
24			reg = <0x800>;
25			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
26			debounce = <15625>;
27			bias-pull-up;
28		};
29
30		usb_id: usb-detect@900 {
31			compatible = "qcom,pm8941-misc";
32			reg = <0x900>;
33			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
34			interrupt-names = "usb_id";
35		};
36
37		smbb: charger@1000 {
38			compatible = "qcom,pm8941-charger";
39			reg = <0x1000>;
40			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
41				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
42				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
43				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
44				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
45				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
46				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
47				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
48			interrupt-names = "chg-done",
49					  "chg-fast",
50					  "chg-trkl",
51					  "bat-temp-ok",
52					  "bat-present",
53					  "chg-gone",
54					  "usb-valid",
55					  "dc-valid";
56
57			usb-otg-in-supply = <&pm8941_5vs1>;
58
59			chg_otg: otg-vbus { };
60		};
61
62		pm8941_gpios: gpio@c000 {
63			compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
64			reg = <0xc000>;
65			gpio-controller;
66			gpio-ranges = <&pm8941_gpios 0 0 36>;
67			#gpio-cells = <2>;
68			interrupt-controller;
69			#interrupt-cells = <2>;
70
71			boost_bypass_n_pin: boost-bypass-state {
72				pins = "gpio21";
73				function = "normal";
74			};
75		};
76
77		pm8941_mpps: mpps@a000 {
78			compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
79			reg = <0xa000>;
80			gpio-controller;
81			#gpio-cells = <2>;
82			gpio-ranges = <&pm8941_mpps 0 0 8>;
83			interrupt-controller;
84			#interrupt-cells = <2>;
85		};
86
87		pm8941_temp: temp-alarm@2400 {
88			compatible = "qcom,spmi-temp-alarm";
89			reg = <0x2400>;
90			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
91			io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
92			io-channel-names = "thermal";
93			#thermal-sensor-cells = <0>;
94		};
95
96		pm8941_vadc: adc@3100 {
97			compatible = "qcom,spmi-vadc";
98			reg = <0x3100>;
99			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
100			#address-cells = <1>;
101			#size-cells = <0>;
102			#io-channel-cells = <1>;
103
104
105			adc-chan@6 {
106				reg = <VADC_VBAT_SNS>;
107			};
108
109			adc-chan@8 {
110				reg = <VADC_DIE_TEMP>;
111			};
112
113			adc-chan@9 {
114				reg = <VADC_REF_625MV>;
115			};
116
117			adc-chan@a {
118				reg = <VADC_REF_1250MV>;
119			};
120
121			adc-chan@e {
122				reg = <VADC_GND_REF>;
123			};
124
125			adc-chan@f {
126				reg = <VADC_VDD_VADC>;
127			};
128
129			adc-chan@30 {
130				reg = <VADC_LR_MUX1_BAT_THERM>;
131			};
132		};
133
134		pm8941_iadc: adc@3600 {
135			compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
136			reg = <0x3600>;
137			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
138			qcom,external-resistor-micro-ohms = <10000>;
139		};
140
141		pm8941_coincell: charger@2800 {
142			compatible = "qcom,pm8941-coincell";
143			reg = <0x2800>;
144			status = "disabled";
145		};
146	};
147
148	pm8941_1: pm8941@1 {
149		compatible = "qcom,pm8941", "qcom,spmi-pmic";
150		reg = <0x1 SPMI_USID>;
151		#address-cells = <1>;
152		#size-cells = <0>;
153
154		pm8941_lpg: pwm {
155			compatible = "qcom,pm8941-lpg";
156
157			#address-cells = <1>;
158			#size-cells = <0>;
159			#pwm-cells = <2>;
160
161			status = "disabled";
162		};
163
164		pm8941_vib: vibrator@c000 {
165			compatible = "qcom,pm8916-vib";
166			reg = <0xc000>;
167			status = "disabled";
168		};
169
170		pm8941_wled: wled@d800 {
171			compatible = "qcom,pm8941-wled";
172			reg = <0xd800>;
173			label = "backlight";
174
175			status = "disabled";
176		};
177
178		regulators {
179			compatible = "qcom,pm8941-regulators";
180			interrupts = <0x1 0x83 0x2 0>, <0x1 0x84 0x2 0>;
181			interrupt-names = "ocp-5vs1", "ocp-5vs2";
182			vin_5vs-supply = <&pm8941_5v>;
183
184			pm8941_5v: s4 {
185				regulator-min-microvolt = <5000000>;
186				regulator-max-microvolt = <5000000>;
187				regulator-enable-ramp-delay = <500>;
188			};
189
190			pm8941_5vs1: 5vs1 {
191				regulator-enable-ramp-delay = <1000>;
192				regulator-pull-down;
193				regulator-over-current-protection;
194				qcom,ocp-max-retries = <10>;
195				qcom,ocp-retry-delay = <30>;
196				qcom,vs-soft-start-strength = <0>;
197				regulator-initial-mode = <1>;
198			};
199
200			pm8941_5vs2: 5vs2 {
201				regulator-enable-ramp-delay = <1000>;
202				regulator-pull-down;
203				regulator-over-current-protection;
204				qcom,ocp-max-retries = <10>;
205				qcom,ocp-retry-delay = <30>;
206				qcom,vs-soft-start-strength = <0>;
207				regulator-initial-mode = <1>;
208			};
209		};
210	};
211};
212