1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (C) 2008-2009 ST-Ericsson SA
4 *
5 * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
6 */
7 #include <linux/types.h>
8 #include <linux/init.h>
9 #include <linux/device.h>
10 #include <linux/amba/bus.h>
11 #include <linux/interrupt.h>
12 #include <linux/irq.h>
13 #include <linux/irqchip.h>
14 #include <linux/irqchip/arm-gic.h>
15 #include <linux/mfd/dbx500-prcmu.h>
16 #include <linux/platform_data/arm-ux500-pm.h>
17 #include <linux/platform_device.h>
18 #include <linux/io.h>
19 #include <linux/of.h>
20 #include <linux/of_address.h>
21 #include <linux/of_platform.h>
22 #include <linux/regulator/machine.h>
23
24 #include <asm/outercache.h>
25 #include <asm/hardware/cache-l2x0.h>
26 #include <asm/mach/map.h>
27 #include <asm/mach/arch.h>
28
29 #include "pm_domains.h"
30
ux500_l2x0_unlock(void)31 static int __init ux500_l2x0_unlock(void)
32 {
33 int i;
34 struct device_node *np;
35 void __iomem *l2x0_base;
36
37 np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
38 l2x0_base = of_iomap(np, 0);
39 of_node_put(np);
40 if (!l2x0_base)
41 return -ENODEV;
42
43 /*
44 * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
45 * apparently locks both caches before jumping to the kernel. The
46 * l2x0 core will not touch the unlock registers if the l2x0 is
47 * already enabled, so we do it right here instead. The PL310 has
48 * 8 sets of registers, one per possible CPU.
49 */
50 for (i = 0; i < 8; i++) {
51 writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
52 i * L2X0_LOCKDOWN_STRIDE);
53 writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
54 i * L2X0_LOCKDOWN_STRIDE);
55 }
56 iounmap(l2x0_base);
57 return 0;
58 }
59
ux500_l2c310_write_sec(unsigned long val,unsigned reg)60 static void ux500_l2c310_write_sec(unsigned long val, unsigned reg)
61 {
62 /*
63 * We can't write to secure registers as we are in non-secure
64 * mode, until we have some SMI service available.
65 */
66 }
67
68 /*
69 * FIXME: Should we set up the GPIO domain here?
70 *
71 * The problem is that we cannot put the interrupt resources into the platform
72 * device until the irqdomain has been added. Right now, we set the GIC interrupt
73 * domain from init_irq(), then load the gpio driver from
74 * core_initcall(nmk_gpio_init) and add the platform devices from
75 * arch_initcall(customize_machine).
76 *
77 * This feels fragile because it depends on the gpio device getting probed
78 * _before_ any device uses the gpio interrupts.
79 */
ux500_init_irq(void)80 static void __init ux500_init_irq(void)
81 {
82 struct device_node *np;
83 struct resource r;
84
85 irqchip_init();
86 prcmu_early_init();
87 np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
88 of_address_to_resource(np, 0, &r);
89 of_node_put(np);
90 if (!r.start) {
91 pr_err("could not find PRCMU base resource\n");
92 return;
93 }
94 ux500_pm_init(r.start, r.end-r.start);
95
96 /* Unlock before init */
97 ux500_l2x0_unlock();
98 outer_cache.write_sec = ux500_l2c310_write_sec;
99 }
100
ux500_restart(enum reboot_mode mode,const char * cmd)101 static void ux500_restart(enum reboot_mode mode, const char *cmd)
102 {
103 local_irq_disable();
104 local_fiq_disable();
105
106 prcmu_system_reset(0);
107 }
108
109 static const struct of_device_id u8500_local_bus_nodes[] = {
110 /* only create devices below soc node */
111 { .compatible = "stericsson,db8500", },
112 { .compatible = "simple-bus"},
113 { },
114 };
115
u8500_init_machine(void)116 static void __init u8500_init_machine(void)
117 {
118 /* Initialize ux500 power domains */
119 ux500_pm_domains_init();
120
121 of_platform_populate(NULL, u8500_local_bus_nodes,
122 NULL, NULL);
123 }
124
125 static const char * stericsson_dt_platform_compat[] = {
126 "st-ericsson,u8500",
127 "st-ericsson,u9500",
128 NULL,
129 };
130
131 DT_MACHINE_START(U8500_DT, "ST-Ericsson Ux5x0 platform (Device Tree Support)")
132 .l2c_aux_val = 0,
133 .l2c_aux_mask = ~0,
134 .init_irq = ux500_init_irq,
135 .init_machine = u8500_init_machine,
136 .dt_compat = stericsson_dt_platform_compat,
137 .restart = ux500_restart,
138 MACHINE_END
139