1 /* SPDX-License-Identifier: GPL-2.0 */
2 #ifndef _ASM_SPARC_DMA_H
3 #define _ASM_SPARC_DMA_H
4 
5 /* These are irrelevant for Sparc DMA, but we leave it in so that
6  * things can compile.
7  */
8 #define MAX_DMA_CHANNELS 8
9 #define DMA_MODE_READ    1
10 #define DMA_MODE_WRITE   2
11 #define MAX_DMA_ADDRESS  (~0UL)
12 
13 /* Useful constants */
14 #define SIZE_16MB      (16*1024*1024)
15 #define SIZE_64K       (64*1024)
16 
17 /* SBUS DMA controller reg offsets */
18 #define DMA_CSR		0x00UL		/* rw  DMA control/status register    0x00   */
19 #define DMA_ADDR	0x04UL		/* rw  DMA transfer address register  0x04   */
20 #define DMA_COUNT	0x08UL		/* rw  DMA transfer count register    0x08   */
21 #define DMA_TEST	0x0cUL		/* rw  DMA test/debug register        0x0c   */
22 
23 /* Fields in the cond_reg register */
24 /* First, the version identification bits */
25 #define DMA_DEVICE_ID    0xf0000000        /* Device identification bits */
26 #define DMA_VERS0        0x00000000        /* Sunray DMA version */
27 #define DMA_ESCV1        0x40000000        /* DMA ESC Version 1 */
28 #define DMA_VERS1        0x80000000        /* DMA rev 1 */
29 #define DMA_VERS2        0xa0000000        /* DMA rev 2 */
30 #define DMA_VERHME       0xb0000000        /* DMA hme gate array */
31 #define DMA_VERSPLUS     0x90000000        /* DMA rev 1 PLUS */
32 
33 #define DMA_HNDL_INTR    0x00000001        /* An IRQ needs to be handled */
34 #define DMA_HNDL_ERROR   0x00000002        /* We need to take an error */
35 #define DMA_FIFO_ISDRAIN 0x0000000c        /* The DMA FIFO is draining */
36 #define DMA_INT_ENAB     0x00000010        /* Turn on interrupts */
37 #define DMA_FIFO_INV     0x00000020        /* Invalidate the FIFO */
38 #define DMA_ACC_SZ_ERR   0x00000040        /* The access size was bad */
39 #define DMA_FIFO_STDRAIN 0x00000040        /* DMA_VERS1 Drain the FIFO */
40 #define DMA_RST_SCSI     0x00000080        /* Reset the SCSI controller */
41 #define DMA_RST_ENET     DMA_RST_SCSI      /* Reset the ENET controller */
42 #define DMA_ST_WRITE     0x00000100        /* write from device to memory */
43 #define DMA_ENABLE       0x00000200        /* Fire up DMA, handle requests */
44 #define DMA_PEND_READ    0x00000400        /* DMA_VERS1/0/PLUS Pending Read */
45 #define DMA_ESC_BURST    0x00000800        /* 1=16byte 0=32byte */
46 #define DMA_READ_AHEAD   0x00001800        /* DMA read ahead partial longword */
47 #define DMA_DSBL_RD_DRN  0x00001000        /* No EC drain on slave reads */
48 #define DMA_BCNT_ENAB    0x00002000        /* If on, use the byte counter */
49 #define DMA_TERM_CNTR    0x00004000        /* Terminal counter */
50 #define DMA_SCSI_SBUS64  0x00008000        /* HME: Enable 64-bit SBUS mode. */
51 #define DMA_CSR_DISAB    0x00010000        /* No FIFO drains during csr */
52 #define DMA_SCSI_DISAB   0x00020000        /* No FIFO drains during reg */
53 #define DMA_DSBL_WR_INV  0x00020000        /* No EC inval. on slave writes */
54 #define DMA_ADD_ENABLE   0x00040000        /* Special ESC DVMA optimization */
55 #define DMA_E_BURSTS	 0x000c0000	   /* ENET: SBUS r/w burst mask */
56 #define DMA_E_BURST32	 0x00040000	   /* ENET: SBUS 32 byte r/w burst */
57 #define DMA_E_BURST16	 0x00000000	   /* ENET: SBUS 16 byte r/w burst */
58 #define DMA_BRST_SZ      0x000c0000        /* SCSI: SBUS r/w burst size */
59 #define DMA_BRST64       0x000c0000        /* SCSI: 64byte bursts (HME on UltraSparc only) */
60 #define DMA_BRST32       0x00040000        /* SCSI: 32byte bursts */
61 #define DMA_BRST16       0x00000000        /* SCSI: 16byte bursts */
62 #define DMA_BRST0        0x00080000        /* SCSI: no bursts (non-HME gate arrays) */
63 #define DMA_ADDR_DISAB   0x00100000        /* No FIFO drains during addr */
64 #define DMA_2CLKS        0x00200000        /* Each transfer = 2 clock ticks */
65 #define DMA_3CLKS        0x00400000        /* Each transfer = 3 clock ticks */
66 #define DMA_EN_ENETAUI   DMA_3CLKS         /* Put lance into AUI-cable mode */
67 #define DMA_CNTR_DISAB   0x00800000        /* No IRQ when DMA_TERM_CNTR set */
68 #define DMA_AUTO_NADDR   0x01000000        /* Use "auto nxt addr" feature */
69 #define DMA_SCSI_ON      0x02000000        /* Enable SCSI dma */
70 #define DMA_PARITY_OFF   0x02000000        /* HME: disable parity checking */
71 #define DMA_LOADED_ADDR  0x04000000        /* Address has been loaded */
72 #define DMA_LOADED_NADDR 0x08000000        /* Next address has been loaded */
73 #define DMA_RESET_FAS366 0x08000000        /* HME: Assert RESET to FAS366 */
74 
75 /* Values describing the burst-size property from the PROM */
76 #define DMA_BURST1       0x01
77 #define DMA_BURST2       0x02
78 #define DMA_BURST4       0x04
79 #define DMA_BURST8       0x08
80 #define DMA_BURST16      0x10
81 #define DMA_BURST32      0x20
82 #define DMA_BURST64      0x40
83 #define DMA_BURSTBITS    0x7f
84 
85 #ifdef CONFIG_SPARC32
86 struct device;
87 
88 unsigned long sparc_dma_alloc_resource(struct device *dev, size_t len);
89 bool sparc_dma_free_resource(void *cpu_addr, size_t size);
90 #endif
91 
92 #endif /* !(_ASM_SPARC_DMA_H) */
93