1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (C) ST-Ericsson SA 2010
4 *
5 * Author: Arun R Murthy <arun.murthy@stericsson.com>
6 * Author: Daniel Willerud <daniel.willerud@stericsson.com>
7 * Author: Johan Palsson <johan.palsson@stericsson.com>
8 * Author: M'boumba Cedric Madianga
9 * Author: Linus Walleij <linus.walleij@linaro.org>
10 *
11 * AB8500 General Purpose ADC driver. The AB8500 uses reference voltages:
12 * VinVADC, and VADC relative to GND to do its job. It monitors main and backup
13 * battery voltages, AC (mains) voltage, USB cable voltage, as well as voltages
14 * representing the temperature of the chip die and battery, accessory
15 * detection by resistance measurements using relative voltages and GSM burst
16 * information.
17 *
18 * Some of the voltages are measured on external pins on the IC, such as
19 * battery temperature or "ADC aux" 1 and 2. Other voltages are internal rails
20 * from other parts of the ASIC such as main charger voltage, main and battery
21 * backup voltage or USB VBUS voltage. For this reason drivers for other
22 * parts of the system are required to obtain handles to the ADC to do work
23 * for them and the IIO driver provides arbitration among these consumers.
24 */
25 #include <linux/init.h>
26 #include <linux/bits.h>
27 #include <linux/iio/iio.h>
28 #include <linux/iio/sysfs.h>
29 #include <linux/device.h>
30 #include <linux/interrupt.h>
31 #include <linux/spinlock.h>
32 #include <linux/delay.h>
33 #include <linux/pm_runtime.h>
34 #include <linux/platform_device.h>
35 #include <linux/completion.h>
36 #include <linux/regulator/consumer.h>
37 #include <linux/random.h>
38 #include <linux/err.h>
39 #include <linux/slab.h>
40 #include <linux/mfd/abx500.h>
41 #include <linux/mfd/abx500/ab8500.h>
42
43 /* GPADC register offsets and bit definitions */
44
45 #define AB8500_GPADC_CTRL1_REG 0x00
46 /* GPADC control register 1 bits */
47 #define AB8500_GPADC_CTRL1_DISABLE 0x00
48 #define AB8500_GPADC_CTRL1_ENABLE BIT(0)
49 #define AB8500_GPADC_CTRL1_TRIG_ENA BIT(1)
50 #define AB8500_GPADC_CTRL1_START_SW_CONV BIT(2)
51 #define AB8500_GPADC_CTRL1_BTEMP_PULL_UP BIT(3)
52 /* 0 = use rising edge, 1 = use falling edge */
53 #define AB8500_GPADC_CTRL1_TRIG_EDGE BIT(4)
54 /* 0 = use VTVOUT, 1 = use VRTC as pull-up supply for battery temp NTC */
55 #define AB8500_GPADC_CTRL1_PUPSUPSEL BIT(5)
56 #define AB8500_GPADC_CTRL1_BUF_ENA BIT(6)
57 #define AB8500_GPADC_CTRL1_ICHAR_ENA BIT(7)
58
59 #define AB8500_GPADC_CTRL2_REG 0x01
60 #define AB8500_GPADC_CTRL3_REG 0x02
61 /*
62 * GPADC control register 2 and 3 bits
63 * the bit layout is the same for SW and HW conversion set-up
64 */
65 #define AB8500_GPADC_CTRL2_AVG_1 0x00
66 #define AB8500_GPADC_CTRL2_AVG_4 BIT(5)
67 #define AB8500_GPADC_CTRL2_AVG_8 BIT(6)
68 #define AB8500_GPADC_CTRL2_AVG_16 (BIT(5) | BIT(6))
69
70 enum ab8500_gpadc_channel {
71 AB8500_GPADC_CHAN_UNUSED = 0x00,
72 AB8500_GPADC_CHAN_BAT_CTRL = 0x01,
73 AB8500_GPADC_CHAN_BAT_TEMP = 0x02,
74 /* This is not used on AB8505 */
75 AB8500_GPADC_CHAN_MAIN_CHARGER = 0x03,
76 AB8500_GPADC_CHAN_ACC_DET_1 = 0x04,
77 AB8500_GPADC_CHAN_ACC_DET_2 = 0x05,
78 AB8500_GPADC_CHAN_ADC_AUX_1 = 0x06,
79 AB8500_GPADC_CHAN_ADC_AUX_2 = 0x07,
80 AB8500_GPADC_CHAN_VBAT_A = 0x08,
81 AB8500_GPADC_CHAN_VBUS = 0x09,
82 AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT = 0x0a,
83 AB8500_GPADC_CHAN_USB_CHARGER_CURRENT = 0x0b,
84 AB8500_GPADC_CHAN_BACKUP_BAT = 0x0c,
85 /* Only on AB8505 */
86 AB8505_GPADC_CHAN_DIE_TEMP = 0x0d,
87 AB8500_GPADC_CHAN_ID = 0x0e,
88 AB8500_GPADC_CHAN_INTERNAL_TEST_1 = 0x0f,
89 AB8500_GPADC_CHAN_INTERNAL_TEST_2 = 0x10,
90 AB8500_GPADC_CHAN_INTERNAL_TEST_3 = 0x11,
91 /* FIXME: Applicable to all ASIC variants? */
92 AB8500_GPADC_CHAN_XTAL_TEMP = 0x12,
93 AB8500_GPADC_CHAN_VBAT_TRUE_MEAS = 0x13,
94 /* FIXME: Doesn't seem to work with pure AB8500 */
95 AB8500_GPADC_CHAN_BAT_CTRL_AND_IBAT = 0x1c,
96 AB8500_GPADC_CHAN_VBAT_MEAS_AND_IBAT = 0x1d,
97 AB8500_GPADC_CHAN_VBAT_TRUE_MEAS_AND_IBAT = 0x1e,
98 AB8500_GPADC_CHAN_BAT_TEMP_AND_IBAT = 0x1f,
99 /*
100 * Virtual channel used only for ibat conversion to ampere.
101 * Battery current conversion (ibat) cannot be requested as a
102 * single conversion but it is always requested in combination
103 * with other input requests.
104 */
105 AB8500_GPADC_CHAN_IBAT_VIRTUAL = 0xFF,
106 };
107
108 #define AB8500_GPADC_AUTO_TIMER_REG 0x03
109
110 #define AB8500_GPADC_STAT_REG 0x04
111 #define AB8500_GPADC_STAT_BUSY BIT(0)
112
113 #define AB8500_GPADC_MANDATAL_REG 0x05
114 #define AB8500_GPADC_MANDATAH_REG 0x06
115 #define AB8500_GPADC_AUTODATAL_REG 0x07
116 #define AB8500_GPADC_AUTODATAH_REG 0x08
117 #define AB8500_GPADC_MUX_CTRL_REG 0x09
118 #define AB8540_GPADC_MANDATA2L_REG 0x09
119 #define AB8540_GPADC_MANDATA2H_REG 0x0A
120 #define AB8540_GPADC_APEAAX_REG 0x10
121 #define AB8540_GPADC_APEAAT_REG 0x11
122 #define AB8540_GPADC_APEAAM_REG 0x12
123 #define AB8540_GPADC_APEAAH_REG 0x13
124 #define AB8540_GPADC_APEAAL_REG 0x14
125
126 /*
127 * OTP register offsets
128 * Bank : 0x15
129 */
130 #define AB8500_GPADC_CAL_1 0x0F
131 #define AB8500_GPADC_CAL_2 0x10
132 #define AB8500_GPADC_CAL_3 0x11
133 #define AB8500_GPADC_CAL_4 0x12
134 #define AB8500_GPADC_CAL_5 0x13
135 #define AB8500_GPADC_CAL_6 0x14
136 #define AB8500_GPADC_CAL_7 0x15
137 /* New calibration for 8540 */
138 #define AB8540_GPADC_OTP4_REG_7 0x38
139 #define AB8540_GPADC_OTP4_REG_6 0x39
140 #define AB8540_GPADC_OTP4_REG_5 0x3A
141
142 #define AB8540_GPADC_DIS_ZERO 0x00
143 #define AB8540_GPADC_EN_VBIAS_XTAL_TEMP 0x02
144
145 /* GPADC constants from AB8500 spec, UM0836 */
146 #define AB8500_ADC_RESOLUTION 1024
147 #define AB8500_ADC_CH_BTEMP_MIN 0
148 #define AB8500_ADC_CH_BTEMP_MAX 1350
149 #define AB8500_ADC_CH_DIETEMP_MIN 0
150 #define AB8500_ADC_CH_DIETEMP_MAX 1350
151 #define AB8500_ADC_CH_CHG_V_MIN 0
152 #define AB8500_ADC_CH_CHG_V_MAX 20030
153 #define AB8500_ADC_CH_ACCDET2_MIN 0
154 #define AB8500_ADC_CH_ACCDET2_MAX 2500
155 #define AB8500_ADC_CH_VBAT_MIN 2300
156 #define AB8500_ADC_CH_VBAT_MAX 4800
157 #define AB8500_ADC_CH_CHG_I_MIN 0
158 #define AB8500_ADC_CH_CHG_I_MAX 1500
159 #define AB8500_ADC_CH_BKBAT_MIN 0
160 #define AB8500_ADC_CH_BKBAT_MAX 3200
161
162 /* GPADC constants from AB8540 spec */
163 #define AB8500_ADC_CH_IBAT_MIN (-6000) /* mA range measured by ADC for ibat */
164 #define AB8500_ADC_CH_IBAT_MAX 6000
165 #define AB8500_ADC_CH_IBAT_MIN_V (-60) /* mV range measured by ADC for ibat */
166 #define AB8500_ADC_CH_IBAT_MAX_V 60
167 #define AB8500_GPADC_IBAT_VDROP_L (-56) /* mV */
168 #define AB8500_GPADC_IBAT_VDROP_H 56
169
170 /* This is used to not lose precision when dividing to get gain and offset */
171 #define AB8500_GPADC_CALIB_SCALE 1000
172 /*
173 * Number of bits shift used to not lose precision
174 * when dividing to get ibat gain.
175 */
176 #define AB8500_GPADC_CALIB_SHIFT_IBAT 20
177
178 /* Time in ms before disabling regulator */
179 #define AB8500_GPADC_AUTOSUSPEND_DELAY 1
180
181 #define AB8500_GPADC_CONVERSION_TIME 500 /* ms */
182
183 enum ab8500_cal_channels {
184 AB8500_CAL_VMAIN = 0,
185 AB8500_CAL_BTEMP,
186 AB8500_CAL_VBAT,
187 AB8500_CAL_IBAT,
188 AB8500_CAL_NR,
189 };
190
191 /**
192 * struct ab8500_adc_cal_data - Table for storing gain and offset for the
193 * calibrated ADC channels
194 * @gain: Gain of the ADC channel
195 * @offset: Offset of the ADC channel
196 * @otp_calib_hi: Calibration from OTP
197 * @otp_calib_lo: Calibration from OTP
198 */
199 struct ab8500_adc_cal_data {
200 s64 gain;
201 s64 offset;
202 u16 otp_calib_hi;
203 u16 otp_calib_lo;
204 };
205
206 /**
207 * struct ab8500_gpadc_chan_info - per-channel GPADC info
208 * @name: name of the channel
209 * @id: the internal AB8500 ID number for the channel
210 * @hardware_control: indicate that we want to use hardware ADC control
211 * on this channel, the default is software ADC control. Hardware control
212 * is normally only used to test the battery voltage during GSM bursts
213 * and needs a hardware trigger on the GPADCTrig pin of the ASIC.
214 * @falling_edge: indicate that we want to trigger on falling edge
215 * rather than rising edge, rising edge is the default
216 * @avg_sample: how many samples to average: must be 1, 4, 8 or 16.
217 * @trig_timer: how long to wait for the trigger, in 32kHz periods:
218 * 0 .. 255 periods
219 */
220 struct ab8500_gpadc_chan_info {
221 const char *name;
222 u8 id;
223 bool hardware_control;
224 bool falling_edge;
225 u8 avg_sample;
226 u8 trig_timer;
227 };
228
229 /**
230 * struct ab8500_gpadc - AB8500 GPADC device information
231 * @dev: pointer to the containing device
232 * @ab8500: pointer to the parent AB8500 device
233 * @chans: internal per-channel information container
234 * @nchans: number of channels
235 * @complete: pointer to the completion that indicates
236 * the completion of an gpadc conversion cycle
237 * @vddadc: pointer to the regulator supplying VDDADC
238 * @irq_sw: interrupt number that is used by gpadc for software ADC conversion
239 * @irq_hw: interrupt number that is used by gpadc for hardware ADC conversion
240 * @cal_data: array of ADC calibration data structs
241 */
242 struct ab8500_gpadc {
243 struct device *dev;
244 struct ab8500 *ab8500;
245 struct ab8500_gpadc_chan_info *chans;
246 unsigned int nchans;
247 struct completion complete;
248 struct regulator *vddadc;
249 int irq_sw;
250 int irq_hw;
251 struct ab8500_adc_cal_data cal_data[AB8500_CAL_NR];
252 };
253
254 static struct ab8500_gpadc_chan_info *
ab8500_gpadc_get_channel(struct ab8500_gpadc * gpadc,u8 chan)255 ab8500_gpadc_get_channel(struct ab8500_gpadc *gpadc, u8 chan)
256 {
257 struct ab8500_gpadc_chan_info *ch;
258 int i;
259
260 for (i = 0; i < gpadc->nchans; i++) {
261 ch = &gpadc->chans[i];
262 if (ch->id == chan)
263 break;
264 }
265 if (i == gpadc->nchans)
266 return NULL;
267
268 return ch;
269 }
270
271 /**
272 * ab8500_gpadc_ad_to_voltage() - Convert a raw ADC value to a voltage
273 * @gpadc: GPADC instance
274 * @ch: the sampled channel this raw value is coming from
275 * @ad_value: the raw value
276 */
ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc * gpadc,enum ab8500_gpadc_channel ch,int ad_value)277 static int ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc *gpadc,
278 enum ab8500_gpadc_channel ch,
279 int ad_value)
280 {
281 int res;
282
283 switch (ch) {
284 case AB8500_GPADC_CHAN_MAIN_CHARGER:
285 /* No calibration data available: just interpolate */
286 if (!gpadc->cal_data[AB8500_CAL_VMAIN].gain) {
287 res = AB8500_ADC_CH_CHG_V_MIN + (AB8500_ADC_CH_CHG_V_MAX -
288 AB8500_ADC_CH_CHG_V_MIN) * ad_value /
289 AB8500_ADC_RESOLUTION;
290 break;
291 }
292 /* Here we can use calibration */
293 res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_VMAIN].gain +
294 gpadc->cal_data[AB8500_CAL_VMAIN].offset) / AB8500_GPADC_CALIB_SCALE;
295 break;
296
297 case AB8500_GPADC_CHAN_BAT_CTRL:
298 case AB8500_GPADC_CHAN_BAT_TEMP:
299 case AB8500_GPADC_CHAN_ACC_DET_1:
300 case AB8500_GPADC_CHAN_ADC_AUX_1:
301 case AB8500_GPADC_CHAN_ADC_AUX_2:
302 case AB8500_GPADC_CHAN_XTAL_TEMP:
303 /* No calibration data available: just interpolate */
304 if (!gpadc->cal_data[AB8500_CAL_BTEMP].gain) {
305 res = AB8500_ADC_CH_BTEMP_MIN + (AB8500_ADC_CH_BTEMP_MAX -
306 AB8500_ADC_CH_BTEMP_MIN) * ad_value /
307 AB8500_ADC_RESOLUTION;
308 break;
309 }
310 /* Here we can use calibration */
311 res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_BTEMP].gain +
312 gpadc->cal_data[AB8500_CAL_BTEMP].offset) / AB8500_GPADC_CALIB_SCALE;
313 break;
314
315 case AB8500_GPADC_CHAN_VBAT_A:
316 case AB8500_GPADC_CHAN_VBAT_TRUE_MEAS:
317 /* No calibration data available: just interpolate */
318 if (!gpadc->cal_data[AB8500_CAL_VBAT].gain) {
319 res = AB8500_ADC_CH_VBAT_MIN + (AB8500_ADC_CH_VBAT_MAX -
320 AB8500_ADC_CH_VBAT_MIN) * ad_value /
321 AB8500_ADC_RESOLUTION;
322 break;
323 }
324 /* Here we can use calibration */
325 res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_VBAT].gain +
326 gpadc->cal_data[AB8500_CAL_VBAT].offset) / AB8500_GPADC_CALIB_SCALE;
327 break;
328
329 case AB8505_GPADC_CHAN_DIE_TEMP:
330 res = AB8500_ADC_CH_DIETEMP_MIN +
331 (AB8500_ADC_CH_DIETEMP_MAX - AB8500_ADC_CH_DIETEMP_MIN) * ad_value /
332 AB8500_ADC_RESOLUTION;
333 break;
334
335 case AB8500_GPADC_CHAN_ACC_DET_2:
336 res = AB8500_ADC_CH_ACCDET2_MIN +
337 (AB8500_ADC_CH_ACCDET2_MAX - AB8500_ADC_CH_ACCDET2_MIN) * ad_value /
338 AB8500_ADC_RESOLUTION;
339 break;
340
341 case AB8500_GPADC_CHAN_VBUS:
342 res = AB8500_ADC_CH_CHG_V_MIN +
343 (AB8500_ADC_CH_CHG_V_MAX - AB8500_ADC_CH_CHG_V_MIN) * ad_value /
344 AB8500_ADC_RESOLUTION;
345 break;
346
347 case AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT:
348 case AB8500_GPADC_CHAN_USB_CHARGER_CURRENT:
349 res = AB8500_ADC_CH_CHG_I_MIN +
350 (AB8500_ADC_CH_CHG_I_MAX - AB8500_ADC_CH_CHG_I_MIN) * ad_value /
351 AB8500_ADC_RESOLUTION;
352 break;
353
354 case AB8500_GPADC_CHAN_BACKUP_BAT:
355 res = AB8500_ADC_CH_BKBAT_MIN +
356 (AB8500_ADC_CH_BKBAT_MAX - AB8500_ADC_CH_BKBAT_MIN) * ad_value /
357 AB8500_ADC_RESOLUTION;
358 break;
359
360 case AB8500_GPADC_CHAN_IBAT_VIRTUAL:
361 /* No calibration data available: just interpolate */
362 if (!gpadc->cal_data[AB8500_CAL_IBAT].gain) {
363 res = AB8500_ADC_CH_IBAT_MIN + (AB8500_ADC_CH_IBAT_MAX -
364 AB8500_ADC_CH_IBAT_MIN) * ad_value /
365 AB8500_ADC_RESOLUTION;
366 break;
367 }
368 /* Here we can use calibration */
369 res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_IBAT].gain +
370 gpadc->cal_data[AB8500_CAL_IBAT].offset)
371 >> AB8500_GPADC_CALIB_SHIFT_IBAT;
372 break;
373
374 default:
375 dev_err(gpadc->dev,
376 "unknown channel ID: %d, not possible to convert\n",
377 ch);
378 res = -EINVAL;
379 break;
380
381 }
382
383 return res;
384 }
385
ab8500_gpadc_read(struct ab8500_gpadc * gpadc,const struct ab8500_gpadc_chan_info * ch,int * ibat)386 static int ab8500_gpadc_read(struct ab8500_gpadc *gpadc,
387 const struct ab8500_gpadc_chan_info *ch,
388 int *ibat)
389 {
390 int ret;
391 int looplimit = 0;
392 unsigned long completion_timeout;
393 u8 val;
394 u8 low_data, high_data, low_data2, high_data2;
395 u8 ctrl1;
396 u8 ctrl23;
397 unsigned int delay_min = 0;
398 unsigned int delay_max = 0;
399 u8 data_low_addr, data_high_addr;
400
401 if (!gpadc)
402 return -ENODEV;
403
404 /* check if conversion is supported */
405 if ((gpadc->irq_sw <= 0) && !ch->hardware_control)
406 return -ENOTSUPP;
407 if ((gpadc->irq_hw <= 0) && ch->hardware_control)
408 return -ENOTSUPP;
409
410 /* Enable vddadc by grabbing PM runtime */
411 pm_runtime_get_sync(gpadc->dev);
412
413 /* Check if ADC is not busy, lock and proceed */
414 do {
415 ret = abx500_get_register_interruptible(gpadc->dev,
416 AB8500_GPADC, AB8500_GPADC_STAT_REG, &val);
417 if (ret < 0)
418 goto out;
419 if (!(val & AB8500_GPADC_STAT_BUSY))
420 break;
421 msleep(20);
422 } while (++looplimit < 10);
423 if (looplimit >= 10 && (val & AB8500_GPADC_STAT_BUSY)) {
424 dev_err(gpadc->dev, "gpadc_conversion: GPADC busy");
425 ret = -EINVAL;
426 goto out;
427 }
428
429 /* Enable GPADC */
430 ctrl1 = AB8500_GPADC_CTRL1_ENABLE;
431
432 /* Select the channel source and set average samples */
433 switch (ch->avg_sample) {
434 case 1:
435 ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_1;
436 break;
437 case 4:
438 ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_4;
439 break;
440 case 8:
441 ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_8;
442 break;
443 default:
444 ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_16;
445 break;
446 }
447
448 if (ch->hardware_control) {
449 ret = abx500_set_register_interruptible(gpadc->dev,
450 AB8500_GPADC, AB8500_GPADC_CTRL3_REG, ctrl23);
451 ctrl1 |= AB8500_GPADC_CTRL1_TRIG_ENA;
452 if (ch->falling_edge)
453 ctrl1 |= AB8500_GPADC_CTRL1_TRIG_EDGE;
454 } else {
455 ret = abx500_set_register_interruptible(gpadc->dev,
456 AB8500_GPADC, AB8500_GPADC_CTRL2_REG, ctrl23);
457 }
458 if (ret < 0) {
459 dev_err(gpadc->dev,
460 "gpadc_conversion: set avg samples failed\n");
461 goto out;
462 }
463
464 /*
465 * Enable ADC, buffering, select rising edge and enable ADC path
466 * charging current sense if it needed, ABB 3.0 needs some special
467 * treatment too.
468 */
469 switch (ch->id) {
470 case AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT:
471 case AB8500_GPADC_CHAN_USB_CHARGER_CURRENT:
472 ctrl1 |= AB8500_GPADC_CTRL1_BUF_ENA |
473 AB8500_GPADC_CTRL1_ICHAR_ENA;
474 break;
475 case AB8500_GPADC_CHAN_BAT_TEMP:
476 if (!is_ab8500_2p0_or_earlier(gpadc->ab8500)) {
477 ctrl1 |= AB8500_GPADC_CTRL1_BUF_ENA |
478 AB8500_GPADC_CTRL1_BTEMP_PULL_UP;
479 /*
480 * Delay might be needed for ABB8500 cut 3.0, if not,
481 * remove when hardware will be available
482 */
483 delay_min = 1000; /* Delay in micro seconds */
484 delay_max = 10000; /* large range optimises sleepmode */
485 break;
486 }
487 fallthrough;
488 default:
489 ctrl1 |= AB8500_GPADC_CTRL1_BUF_ENA;
490 break;
491 }
492
493 /* Write configuration to control register 1 */
494 ret = abx500_set_register_interruptible(gpadc->dev,
495 AB8500_GPADC, AB8500_GPADC_CTRL1_REG, ctrl1);
496 if (ret < 0) {
497 dev_err(gpadc->dev,
498 "gpadc_conversion: set Control register failed\n");
499 goto out;
500 }
501
502 if (delay_min != 0)
503 usleep_range(delay_min, delay_max);
504
505 if (ch->hardware_control) {
506 /* Set trigger delay timer */
507 ret = abx500_set_register_interruptible(gpadc->dev,
508 AB8500_GPADC, AB8500_GPADC_AUTO_TIMER_REG,
509 ch->trig_timer);
510 if (ret < 0) {
511 dev_err(gpadc->dev,
512 "gpadc_conversion: trig timer failed\n");
513 goto out;
514 }
515 completion_timeout = 2 * HZ;
516 data_low_addr = AB8500_GPADC_AUTODATAL_REG;
517 data_high_addr = AB8500_GPADC_AUTODATAH_REG;
518 } else {
519 /* Start SW conversion */
520 ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
521 AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
522 AB8500_GPADC_CTRL1_START_SW_CONV,
523 AB8500_GPADC_CTRL1_START_SW_CONV);
524 if (ret < 0) {
525 dev_err(gpadc->dev,
526 "gpadc_conversion: start s/w conv failed\n");
527 goto out;
528 }
529 completion_timeout = msecs_to_jiffies(AB8500_GPADC_CONVERSION_TIME);
530 data_low_addr = AB8500_GPADC_MANDATAL_REG;
531 data_high_addr = AB8500_GPADC_MANDATAH_REG;
532 }
533
534 /* Wait for completion of conversion */
535 if (!wait_for_completion_timeout(&gpadc->complete,
536 completion_timeout)) {
537 dev_err(gpadc->dev,
538 "timeout didn't receive GPADC conv interrupt\n");
539 ret = -EINVAL;
540 goto out;
541 }
542
543 /* Read the converted RAW data */
544 ret = abx500_get_register_interruptible(gpadc->dev,
545 AB8500_GPADC, data_low_addr, &low_data);
546 if (ret < 0) {
547 dev_err(gpadc->dev,
548 "gpadc_conversion: read low data failed\n");
549 goto out;
550 }
551
552 ret = abx500_get_register_interruptible(gpadc->dev,
553 AB8500_GPADC, data_high_addr, &high_data);
554 if (ret < 0) {
555 dev_err(gpadc->dev,
556 "gpadc_conversion: read high data failed\n");
557 goto out;
558 }
559
560 /* Check if double conversion is required */
561 if ((ch->id == AB8500_GPADC_CHAN_BAT_CTRL_AND_IBAT) ||
562 (ch->id == AB8500_GPADC_CHAN_VBAT_MEAS_AND_IBAT) ||
563 (ch->id == AB8500_GPADC_CHAN_VBAT_TRUE_MEAS_AND_IBAT) ||
564 (ch->id == AB8500_GPADC_CHAN_BAT_TEMP_AND_IBAT)) {
565
566 if (ch->hardware_control) {
567 /* not supported */
568 ret = -ENOTSUPP;
569 dev_err(gpadc->dev,
570 "gpadc_conversion: only SW double conversion supported\n");
571 goto out;
572 } else {
573 /* Read the converted RAW data 2 */
574 ret = abx500_get_register_interruptible(gpadc->dev,
575 AB8500_GPADC, AB8540_GPADC_MANDATA2L_REG,
576 &low_data2);
577 if (ret < 0) {
578 dev_err(gpadc->dev,
579 "gpadc_conversion: read sw low data 2 failed\n");
580 goto out;
581 }
582
583 ret = abx500_get_register_interruptible(gpadc->dev,
584 AB8500_GPADC, AB8540_GPADC_MANDATA2H_REG,
585 &high_data2);
586 if (ret < 0) {
587 dev_err(gpadc->dev,
588 "gpadc_conversion: read sw high data 2 failed\n");
589 goto out;
590 }
591 if (ibat != NULL) {
592 *ibat = (high_data2 << 8) | low_data2;
593 } else {
594 dev_warn(gpadc->dev,
595 "gpadc_conversion: ibat not stored\n");
596 }
597
598 }
599 }
600
601 /* Disable GPADC */
602 ret = abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
603 AB8500_GPADC_CTRL1_REG, AB8500_GPADC_CTRL1_DISABLE);
604 if (ret < 0) {
605 dev_err(gpadc->dev, "gpadc_conversion: disable gpadc failed\n");
606 goto out;
607 }
608
609 /* This eventually drops the regulator */
610 pm_runtime_mark_last_busy(gpadc->dev);
611 pm_runtime_put_autosuspend(gpadc->dev);
612
613 return (high_data << 8) | low_data;
614
615 out:
616 /*
617 * It has shown to be needed to turn off the GPADC if an error occurs,
618 * otherwise we might have problem when waiting for the busy bit in the
619 * GPADC status register to go low. In V1.1 there wait_for_completion
620 * seems to timeout when waiting for an interrupt.. Not seen in V2.0
621 */
622 (void) abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
623 AB8500_GPADC_CTRL1_REG, AB8500_GPADC_CTRL1_DISABLE);
624 pm_runtime_put(gpadc->dev);
625 dev_err(gpadc->dev,
626 "gpadc_conversion: Failed to AD convert channel %d\n", ch->id);
627
628 return ret;
629 }
630
631 /**
632 * ab8500_bm_gpadcconvend_handler() - isr for gpadc conversion completion
633 * @irq: irq number
634 * @data: pointer to the data passed during request irq
635 *
636 * This is a interrupt service routine for gpadc conversion completion.
637 * Notifies the gpadc completion is completed and the converted raw value
638 * can be read from the registers.
639 * Returns IRQ status(IRQ_HANDLED)
640 */
ab8500_bm_gpadcconvend_handler(int irq,void * data)641 static irqreturn_t ab8500_bm_gpadcconvend_handler(int irq, void *data)
642 {
643 struct ab8500_gpadc *gpadc = data;
644
645 complete(&gpadc->complete);
646
647 return IRQ_HANDLED;
648 }
649
650 static int otp_cal_regs[] = {
651 AB8500_GPADC_CAL_1,
652 AB8500_GPADC_CAL_2,
653 AB8500_GPADC_CAL_3,
654 AB8500_GPADC_CAL_4,
655 AB8500_GPADC_CAL_5,
656 AB8500_GPADC_CAL_6,
657 AB8500_GPADC_CAL_7,
658 };
659
660 static int otp4_cal_regs[] = {
661 AB8540_GPADC_OTP4_REG_7,
662 AB8540_GPADC_OTP4_REG_6,
663 AB8540_GPADC_OTP4_REG_5,
664 };
665
ab8500_gpadc_read_calibration_data(struct ab8500_gpadc * gpadc)666 static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc)
667 {
668 int i;
669 int ret[ARRAY_SIZE(otp_cal_regs)];
670 u8 gpadc_cal[ARRAY_SIZE(otp_cal_regs)];
671 int ret_otp4[ARRAY_SIZE(otp4_cal_regs)];
672 u8 gpadc_otp4[ARRAY_SIZE(otp4_cal_regs)];
673 int vmain_high, vmain_low;
674 int btemp_high, btemp_low;
675 int vbat_high, vbat_low;
676 int ibat_high, ibat_low;
677 s64 V_gain, V_offset, V2A_gain, V2A_offset;
678
679 /* First we read all OTP registers and store the error code */
680 for (i = 0; i < ARRAY_SIZE(otp_cal_regs); i++) {
681 ret[i] = abx500_get_register_interruptible(gpadc->dev,
682 AB8500_OTP_EMUL, otp_cal_regs[i], &gpadc_cal[i]);
683 if (ret[i] < 0) {
684 /* Continue anyway: maybe the other registers are OK */
685 dev_err(gpadc->dev, "%s: read otp reg 0x%02x failed\n",
686 __func__, otp_cal_regs[i]);
687 } else {
688 /* Put this in the entropy pool as device-unique */
689 add_device_randomness(&ret[i], sizeof(ret[i]));
690 }
691 }
692
693 /*
694 * The ADC calibration data is stored in OTP registers.
695 * The layout of the calibration data is outlined below and a more
696 * detailed description can be found in UM0836
697 *
698 * vm_h/l = vmain_high/low
699 * bt_h/l = btemp_high/low
700 * vb_h/l = vbat_high/low
701 *
702 * Data bits 8500/9540:
703 * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
704 * |.......|.......|.......|.......|.......|.......|.......|.......
705 * | | vm_h9 | vm_h8
706 * |.......|.......|.......|.......|.......|.......|.......|.......
707 * | | vm_h7 | vm_h6 | vm_h5 | vm_h4 | vm_h3 | vm_h2
708 * |.......|.......|.......|.......|.......|.......|.......|.......
709 * | vm_h1 | vm_h0 | vm_l4 | vm_l3 | vm_l2 | vm_l1 | vm_l0 | bt_h9
710 * |.......|.......|.......|.......|.......|.......|.......|.......
711 * | bt_h8 | bt_h7 | bt_h6 | bt_h5 | bt_h4 | bt_h3 | bt_h2 | bt_h1
712 * |.......|.......|.......|.......|.......|.......|.......|.......
713 * | bt_h0 | bt_l4 | bt_l3 | bt_l2 | bt_l1 | bt_l0 | vb_h9 | vb_h8
714 * |.......|.......|.......|.......|.......|.......|.......|.......
715 * | vb_h7 | vb_h6 | vb_h5 | vb_h4 | vb_h3 | vb_h2 | vb_h1 | vb_h0
716 * |.......|.......|.......|.......|.......|.......|.......|.......
717 * | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 |
718 * |.......|.......|.......|.......|.......|.......|.......|.......
719 *
720 * Data bits 8540:
721 * OTP2
722 * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
723 * |.......|.......|.......|.......|.......|.......|.......|.......
724 * |
725 * |.......|.......|.......|.......|.......|.......|.......|.......
726 * | vm_h9 | vm_h8 | vm_h7 | vm_h6 | vm_h5 | vm_h4 | vm_h3 | vm_h2
727 * |.......|.......|.......|.......|.......|.......|.......|.......
728 * | vm_h1 | vm_h0 | vm_l4 | vm_l3 | vm_l2 | vm_l1 | vm_l0 | bt_h9
729 * |.......|.......|.......|.......|.......|.......|.......|.......
730 * | bt_h8 | bt_h7 | bt_h6 | bt_h5 | bt_h4 | bt_h3 | bt_h2 | bt_h1
731 * |.......|.......|.......|.......|.......|.......|.......|.......
732 * | bt_h0 | bt_l4 | bt_l3 | bt_l2 | bt_l1 | bt_l0 | vb_h9 | vb_h8
733 * |.......|.......|.......|.......|.......|.......|.......|.......
734 * | vb_h7 | vb_h6 | vb_h5 | vb_h4 | vb_h3 | vb_h2 | vb_h1 | vb_h0
735 * |.......|.......|.......|.......|.......|.......|.......|.......
736 * | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 |
737 * |.......|.......|.......|.......|.......|.......|.......|.......
738 *
739 * Data bits 8540:
740 * OTP4
741 * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
742 * |.......|.......|.......|.......|.......|.......|.......|.......
743 * | | ib_h9 | ib_h8 | ib_h7
744 * |.......|.......|.......|.......|.......|.......|.......|.......
745 * | ib_h6 | ib_h5 | ib_h4 | ib_h3 | ib_h2 | ib_h1 | ib_h0 | ib_l5
746 * |.......|.......|.......|.......|.......|.......|.......|.......
747 * | ib_l4 | ib_l3 | ib_l2 | ib_l1 | ib_l0 |
748 *
749 *
750 * Ideal output ADC codes corresponding to injected input voltages
751 * during manufacturing is:
752 *
753 * vmain_high: Vin = 19500mV / ADC ideal code = 997
754 * vmain_low: Vin = 315mV / ADC ideal code = 16
755 * btemp_high: Vin = 1300mV / ADC ideal code = 985
756 * btemp_low: Vin = 21mV / ADC ideal code = 16
757 * vbat_high: Vin = 4700mV / ADC ideal code = 982
758 * vbat_low: Vin = 2380mV / ADC ideal code = 33
759 */
760
761 if (is_ab8540(gpadc->ab8500)) {
762 /* Calculate gain and offset for VMAIN if all reads succeeded*/
763 if (!(ret[1] < 0 || ret[2] < 0)) {
764 vmain_high = (((gpadc_cal[1] & 0xFF) << 2) |
765 ((gpadc_cal[2] & 0xC0) >> 6));
766 vmain_low = ((gpadc_cal[2] & 0x3E) >> 1);
767
768 gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_hi =
769 (u16)vmain_high;
770 gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_lo =
771 (u16)vmain_low;
772
773 gpadc->cal_data[AB8500_CAL_VMAIN].gain = AB8500_GPADC_CALIB_SCALE *
774 (19500 - 315) / (vmain_high - vmain_low);
775 gpadc->cal_data[AB8500_CAL_VMAIN].offset = AB8500_GPADC_CALIB_SCALE *
776 19500 - (AB8500_GPADC_CALIB_SCALE * (19500 - 315) /
777 (vmain_high - vmain_low)) * vmain_high;
778 } else {
779 gpadc->cal_data[AB8500_CAL_VMAIN].gain = 0;
780 }
781
782 /* Read IBAT calibration Data */
783 for (i = 0; i < ARRAY_SIZE(otp4_cal_regs); i++) {
784 ret_otp4[i] = abx500_get_register_interruptible(
785 gpadc->dev, AB8500_OTP_EMUL,
786 otp4_cal_regs[i], &gpadc_otp4[i]);
787 if (ret_otp4[i] < 0)
788 dev_err(gpadc->dev,
789 "%s: read otp4 reg 0x%02x failed\n",
790 __func__, otp4_cal_regs[i]);
791 }
792
793 /* Calculate gain and offset for IBAT if all reads succeeded */
794 if (!(ret_otp4[0] < 0 || ret_otp4[1] < 0 || ret_otp4[2] < 0)) {
795 ibat_high = (((gpadc_otp4[0] & 0x07) << 7) |
796 ((gpadc_otp4[1] & 0xFE) >> 1));
797 ibat_low = (((gpadc_otp4[1] & 0x01) << 5) |
798 ((gpadc_otp4[2] & 0xF8) >> 3));
799
800 gpadc->cal_data[AB8500_CAL_IBAT].otp_calib_hi =
801 (u16)ibat_high;
802 gpadc->cal_data[AB8500_CAL_IBAT].otp_calib_lo =
803 (u16)ibat_low;
804
805 V_gain = ((AB8500_GPADC_IBAT_VDROP_H - AB8500_GPADC_IBAT_VDROP_L)
806 << AB8500_GPADC_CALIB_SHIFT_IBAT) / (ibat_high - ibat_low);
807
808 V_offset = (AB8500_GPADC_IBAT_VDROP_H << AB8500_GPADC_CALIB_SHIFT_IBAT) -
809 (((AB8500_GPADC_IBAT_VDROP_H - AB8500_GPADC_IBAT_VDROP_L) <<
810 AB8500_GPADC_CALIB_SHIFT_IBAT) / (ibat_high - ibat_low))
811 * ibat_high;
812 /*
813 * Result obtained is in mV (at a scale factor),
814 * we need to calculate gain and offset to get mA
815 */
816 V2A_gain = (AB8500_ADC_CH_IBAT_MAX - AB8500_ADC_CH_IBAT_MIN)/
817 (AB8500_ADC_CH_IBAT_MAX_V - AB8500_ADC_CH_IBAT_MIN_V);
818 V2A_offset = ((AB8500_ADC_CH_IBAT_MAX_V * AB8500_ADC_CH_IBAT_MIN -
819 AB8500_ADC_CH_IBAT_MAX * AB8500_ADC_CH_IBAT_MIN_V)
820 << AB8500_GPADC_CALIB_SHIFT_IBAT)
821 / (AB8500_ADC_CH_IBAT_MAX_V - AB8500_ADC_CH_IBAT_MIN_V);
822
823 gpadc->cal_data[AB8500_CAL_IBAT].gain =
824 V_gain * V2A_gain;
825 gpadc->cal_data[AB8500_CAL_IBAT].offset =
826 V_offset * V2A_gain + V2A_offset;
827 } else {
828 gpadc->cal_data[AB8500_CAL_IBAT].gain = 0;
829 }
830 } else {
831 /* Calculate gain and offset for VMAIN if all reads succeeded */
832 if (!(ret[0] < 0 || ret[1] < 0 || ret[2] < 0)) {
833 vmain_high = (((gpadc_cal[0] & 0x03) << 8) |
834 ((gpadc_cal[1] & 0x3F) << 2) |
835 ((gpadc_cal[2] & 0xC0) >> 6));
836 vmain_low = ((gpadc_cal[2] & 0x3E) >> 1);
837
838 gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_hi =
839 (u16)vmain_high;
840 gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_lo =
841 (u16)vmain_low;
842
843 gpadc->cal_data[AB8500_CAL_VMAIN].gain = AB8500_GPADC_CALIB_SCALE *
844 (19500 - 315) / (vmain_high - vmain_low);
845
846 gpadc->cal_data[AB8500_CAL_VMAIN].offset = AB8500_GPADC_CALIB_SCALE *
847 19500 - (AB8500_GPADC_CALIB_SCALE * (19500 - 315) /
848 (vmain_high - vmain_low)) * vmain_high;
849 } else {
850 gpadc->cal_data[AB8500_CAL_VMAIN].gain = 0;
851 }
852 }
853
854 /* Calculate gain and offset for BTEMP if all reads succeeded */
855 if (!(ret[2] < 0 || ret[3] < 0 || ret[4] < 0)) {
856 btemp_high = (((gpadc_cal[2] & 0x01) << 9) |
857 (gpadc_cal[3] << 1) | ((gpadc_cal[4] & 0x80) >> 7));
858 btemp_low = ((gpadc_cal[4] & 0x7C) >> 2);
859
860 gpadc->cal_data[AB8500_CAL_BTEMP].otp_calib_hi = (u16)btemp_high;
861 gpadc->cal_data[AB8500_CAL_BTEMP].otp_calib_lo = (u16)btemp_low;
862
863 gpadc->cal_data[AB8500_CAL_BTEMP].gain =
864 AB8500_GPADC_CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low);
865 gpadc->cal_data[AB8500_CAL_BTEMP].offset = AB8500_GPADC_CALIB_SCALE * 1300 -
866 (AB8500_GPADC_CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low))
867 * btemp_high;
868 } else {
869 gpadc->cal_data[AB8500_CAL_BTEMP].gain = 0;
870 }
871
872 /* Calculate gain and offset for VBAT if all reads succeeded */
873 if (!(ret[4] < 0 || ret[5] < 0 || ret[6] < 0)) {
874 vbat_high = (((gpadc_cal[4] & 0x03) << 8) | gpadc_cal[5]);
875 vbat_low = ((gpadc_cal[6] & 0xFC) >> 2);
876
877 gpadc->cal_data[AB8500_CAL_VBAT].otp_calib_hi = (u16)vbat_high;
878 gpadc->cal_data[AB8500_CAL_VBAT].otp_calib_lo = (u16)vbat_low;
879
880 gpadc->cal_data[AB8500_CAL_VBAT].gain = AB8500_GPADC_CALIB_SCALE *
881 (4700 - 2380) / (vbat_high - vbat_low);
882 gpadc->cal_data[AB8500_CAL_VBAT].offset = AB8500_GPADC_CALIB_SCALE * 4700 -
883 (AB8500_GPADC_CALIB_SCALE * (4700 - 2380) /
884 (vbat_high - vbat_low)) * vbat_high;
885 } else {
886 gpadc->cal_data[AB8500_CAL_VBAT].gain = 0;
887 }
888 }
889
ab8500_gpadc_read_raw(struct iio_dev * indio_dev,struct iio_chan_spec const * chan,int * val,int * val2,long mask)890 static int ab8500_gpadc_read_raw(struct iio_dev *indio_dev,
891 struct iio_chan_spec const *chan,
892 int *val, int *val2, long mask)
893 {
894 struct ab8500_gpadc *gpadc = iio_priv(indio_dev);
895 const struct ab8500_gpadc_chan_info *ch;
896 int raw_val;
897 int processed;
898
899 ch = ab8500_gpadc_get_channel(gpadc, chan->address);
900 if (!ch) {
901 dev_err(gpadc->dev, "no such channel %lu\n",
902 chan->address);
903 return -EINVAL;
904 }
905
906 raw_val = ab8500_gpadc_read(gpadc, ch, NULL);
907 if (raw_val < 0)
908 return raw_val;
909
910 if (mask == IIO_CHAN_INFO_RAW) {
911 *val = raw_val;
912 return IIO_VAL_INT;
913 }
914
915 if (mask == IIO_CHAN_INFO_PROCESSED) {
916 processed = ab8500_gpadc_ad_to_voltage(gpadc, ch->id, raw_val);
917 if (processed < 0)
918 return processed;
919
920 /* Return millivolt or milliamps or millicentigrades */
921 *val = processed;
922 return IIO_VAL_INT;
923 }
924
925 return -EINVAL;
926 }
927
ab8500_gpadc_fwnode_xlate(struct iio_dev * indio_dev,const struct fwnode_reference_args * iiospec)928 static int ab8500_gpadc_fwnode_xlate(struct iio_dev *indio_dev,
929 const struct fwnode_reference_args *iiospec)
930 {
931 int i;
932
933 for (i = 0; i < indio_dev->num_channels; i++)
934 if (indio_dev->channels[i].channel == iiospec->args[0])
935 return i;
936
937 return -EINVAL;
938 }
939
940 static const struct iio_info ab8500_gpadc_info = {
941 .fwnode_xlate = ab8500_gpadc_fwnode_xlate,
942 .read_raw = ab8500_gpadc_read_raw,
943 };
944
ab8500_gpadc_runtime_suspend(struct device * dev)945 static int ab8500_gpadc_runtime_suspend(struct device *dev)
946 {
947 struct iio_dev *indio_dev = dev_get_drvdata(dev);
948 struct ab8500_gpadc *gpadc = iio_priv(indio_dev);
949
950 regulator_disable(gpadc->vddadc);
951
952 return 0;
953 }
954
ab8500_gpadc_runtime_resume(struct device * dev)955 static int ab8500_gpadc_runtime_resume(struct device *dev)
956 {
957 struct iio_dev *indio_dev = dev_get_drvdata(dev);
958 struct ab8500_gpadc *gpadc = iio_priv(indio_dev);
959 int ret;
960
961 ret = regulator_enable(gpadc->vddadc);
962 if (ret)
963 dev_err(dev, "Failed to enable vddadc: %d\n", ret);
964
965 return ret;
966 }
967
968 /**
969 * ab8500_gpadc_parse_channel() - process devicetree channel configuration
970 * @dev: pointer to containing device
971 * @fwnode: fw node for the channel to configure
972 * @ch: channel info to fill in
973 * @iio_chan: IIO channel specification to fill in
974 *
975 * The devicetree will set up the channel for use with the specific device,
976 * and define usage for things like AUX GPADC inputs more precisely.
977 */
ab8500_gpadc_parse_channel(struct device * dev,struct fwnode_handle * fwnode,struct ab8500_gpadc_chan_info * ch,struct iio_chan_spec * iio_chan)978 static int ab8500_gpadc_parse_channel(struct device *dev,
979 struct fwnode_handle *fwnode,
980 struct ab8500_gpadc_chan_info *ch,
981 struct iio_chan_spec *iio_chan)
982 {
983 const char *name = fwnode_get_name(fwnode);
984 u32 chan;
985 int ret;
986
987 ret = fwnode_property_read_u32(fwnode, "reg", &chan);
988 if (ret) {
989 dev_err(dev, "invalid channel number %s\n", name);
990 return ret;
991 }
992 if (chan > AB8500_GPADC_CHAN_BAT_TEMP_AND_IBAT) {
993 dev_err(dev, "%s channel number out of range %d\n", name, chan);
994 return -EINVAL;
995 }
996
997 iio_chan->channel = chan;
998 iio_chan->datasheet_name = name;
999 iio_chan->indexed = 1;
1000 iio_chan->address = chan;
1001 iio_chan->info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
1002 BIT(IIO_CHAN_INFO_PROCESSED);
1003 /* Most are voltages (also temperatures), some are currents */
1004 if ((chan == AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT) ||
1005 (chan == AB8500_GPADC_CHAN_USB_CHARGER_CURRENT))
1006 iio_chan->type = IIO_CURRENT;
1007 else
1008 iio_chan->type = IIO_VOLTAGE;
1009
1010 ch->id = chan;
1011
1012 /* Sensible defaults */
1013 ch->avg_sample = 16;
1014 ch->hardware_control = false;
1015 ch->falling_edge = false;
1016 ch->trig_timer = 0;
1017
1018 return 0;
1019 }
1020
1021 /**
1022 * ab8500_gpadc_parse_channels() - Parse the GPADC channels from DT
1023 * @gpadc: the GPADC to configure the channels for
1024 * @chans: the IIO channels we parsed
1025 * @nchans: the number of IIO channels we parsed
1026 */
ab8500_gpadc_parse_channels(struct ab8500_gpadc * gpadc,struct iio_chan_spec ** chans_parsed,unsigned int * nchans_parsed)1027 static int ab8500_gpadc_parse_channels(struct ab8500_gpadc *gpadc,
1028 struct iio_chan_spec **chans_parsed,
1029 unsigned int *nchans_parsed)
1030 {
1031 struct fwnode_handle *child;
1032 struct ab8500_gpadc_chan_info *ch;
1033 struct iio_chan_spec *iio_chans;
1034 unsigned int nchans;
1035 int i;
1036
1037 nchans = device_get_child_node_count(gpadc->dev);
1038 if (!nchans) {
1039 dev_err(gpadc->dev, "no channel children\n");
1040 return -ENODEV;
1041 }
1042 dev_info(gpadc->dev, "found %d ADC channels\n", nchans);
1043
1044 iio_chans = devm_kcalloc(gpadc->dev, nchans,
1045 sizeof(*iio_chans), GFP_KERNEL);
1046 if (!iio_chans)
1047 return -ENOMEM;
1048
1049 gpadc->chans = devm_kcalloc(gpadc->dev, nchans,
1050 sizeof(*gpadc->chans), GFP_KERNEL);
1051 if (!gpadc->chans)
1052 return -ENOMEM;
1053
1054 i = 0;
1055 device_for_each_child_node(gpadc->dev, child) {
1056 struct iio_chan_spec *iio_chan;
1057 int ret;
1058
1059 ch = &gpadc->chans[i];
1060 iio_chan = &iio_chans[i];
1061
1062 ret = ab8500_gpadc_parse_channel(gpadc->dev, child, ch,
1063 iio_chan);
1064 if (ret) {
1065 fwnode_handle_put(child);
1066 return ret;
1067 }
1068 i++;
1069 }
1070 gpadc->nchans = nchans;
1071 *chans_parsed = iio_chans;
1072 *nchans_parsed = nchans;
1073
1074 return 0;
1075 }
1076
ab8500_gpadc_probe(struct platform_device * pdev)1077 static int ab8500_gpadc_probe(struct platform_device *pdev)
1078 {
1079 struct ab8500_gpadc *gpadc;
1080 struct iio_dev *indio_dev;
1081 struct device *dev = &pdev->dev;
1082 struct iio_chan_spec *iio_chans;
1083 unsigned int n_iio_chans;
1084 int ret;
1085
1086 indio_dev = devm_iio_device_alloc(dev, sizeof(*gpadc));
1087 if (!indio_dev)
1088 return -ENOMEM;
1089
1090 platform_set_drvdata(pdev, indio_dev);
1091 gpadc = iio_priv(indio_dev);
1092
1093 gpadc->dev = dev;
1094 gpadc->ab8500 = dev_get_drvdata(dev->parent);
1095
1096 ret = ab8500_gpadc_parse_channels(gpadc, &iio_chans, &n_iio_chans);
1097 if (ret)
1098 return ret;
1099
1100 gpadc->irq_sw = platform_get_irq_byname(pdev, "SW_CONV_END");
1101 if (gpadc->irq_sw < 0)
1102 return dev_err_probe(dev, gpadc->irq_sw,
1103 "failed to get platform sw_conv_end irq\n");
1104
1105 if (is_ab8500(gpadc->ab8500)) {
1106 gpadc->irq_hw = platform_get_irq_byname(pdev, "HW_CONV_END");
1107 if (gpadc->irq_hw < 0)
1108 return dev_err_probe(dev, gpadc->irq_hw,
1109 "failed to get platform hw_conv_end irq\n");
1110 } else {
1111 gpadc->irq_hw = 0;
1112 }
1113
1114 /* Initialize completion used to notify completion of conversion */
1115 init_completion(&gpadc->complete);
1116
1117 /* Request interrupts */
1118 ret = devm_request_threaded_irq(dev, gpadc->irq_sw, NULL,
1119 ab8500_bm_gpadcconvend_handler, IRQF_NO_SUSPEND | IRQF_ONESHOT,
1120 "ab8500-gpadc-sw", gpadc);
1121 if (ret < 0) {
1122 dev_err(dev,
1123 "failed to request sw conversion irq %d\n",
1124 gpadc->irq_sw);
1125 return ret;
1126 }
1127
1128 if (gpadc->irq_hw) {
1129 ret = devm_request_threaded_irq(dev, gpadc->irq_hw, NULL,
1130 ab8500_bm_gpadcconvend_handler, IRQF_NO_SUSPEND | IRQF_ONESHOT,
1131 "ab8500-gpadc-hw", gpadc);
1132 if (ret < 0) {
1133 dev_err(dev,
1134 "Failed to request hw conversion irq: %d\n",
1135 gpadc->irq_hw);
1136 return ret;
1137 }
1138 }
1139
1140 /* The VTVout LDO used to power the AB8500 GPADC */
1141 gpadc->vddadc = devm_regulator_get(dev, "vddadc");
1142 if (IS_ERR(gpadc->vddadc))
1143 return dev_err_probe(dev, PTR_ERR(gpadc->vddadc),
1144 "failed to get vddadc\n");
1145
1146 ret = regulator_enable(gpadc->vddadc);
1147 if (ret) {
1148 dev_err(dev, "failed to enable vddadc: %d\n", ret);
1149 return ret;
1150 }
1151
1152 /* Enable runtime PM */
1153 pm_runtime_get_noresume(dev);
1154 pm_runtime_set_active(dev);
1155 pm_runtime_enable(dev);
1156 pm_runtime_set_autosuspend_delay(dev, AB8500_GPADC_AUTOSUSPEND_DELAY);
1157 pm_runtime_use_autosuspend(dev);
1158
1159 ab8500_gpadc_read_calibration_data(gpadc);
1160
1161 pm_runtime_put(dev);
1162
1163 indio_dev->name = "ab8500-gpadc";
1164 indio_dev->modes = INDIO_DIRECT_MODE;
1165 indio_dev->info = &ab8500_gpadc_info;
1166 indio_dev->channels = iio_chans;
1167 indio_dev->num_channels = n_iio_chans;
1168
1169 ret = devm_iio_device_register(dev, indio_dev);
1170 if (ret)
1171 goto out_dis_pm;
1172
1173 return 0;
1174
1175 out_dis_pm:
1176 pm_runtime_get_sync(dev);
1177 pm_runtime_put_noidle(dev);
1178 pm_runtime_disable(dev);
1179 regulator_disable(gpadc->vddadc);
1180
1181 return ret;
1182 }
1183
ab8500_gpadc_remove(struct platform_device * pdev)1184 static int ab8500_gpadc_remove(struct platform_device *pdev)
1185 {
1186 struct iio_dev *indio_dev = platform_get_drvdata(pdev);
1187 struct ab8500_gpadc *gpadc = iio_priv(indio_dev);
1188
1189 pm_runtime_get_sync(gpadc->dev);
1190 pm_runtime_put_noidle(gpadc->dev);
1191 pm_runtime_disable(gpadc->dev);
1192 regulator_disable(gpadc->vddadc);
1193
1194 return 0;
1195 }
1196
1197 static DEFINE_RUNTIME_DEV_PM_OPS(ab8500_gpadc_pm_ops,
1198 ab8500_gpadc_runtime_suspend,
1199 ab8500_gpadc_runtime_resume, NULL);
1200
1201 static struct platform_driver ab8500_gpadc_driver = {
1202 .probe = ab8500_gpadc_probe,
1203 .remove = ab8500_gpadc_remove,
1204 .driver = {
1205 .name = "ab8500-gpadc",
1206 .pm = pm_ptr(&ab8500_gpadc_pm_ops),
1207 },
1208 };
1209 builtin_platform_driver(ab8500_gpadc_driver);
1210