Searched refs:FSI (Results 1 – 20 of 20) sorted by relevance
3 # FSI subsystem6 menuconfig FSI config7 tristate "FSI support"14 if FSI32 tristate "GPIO-based FSI master"39 tristate "FSI hub master"41 This option enables a FSI hub master driver. Hub is a type of FSI57 tristate "FSI ASPEED master"66 tristate "SCOM FSI client device driver"68 This option enables an FSI based SCOM device driver.[all …]
1 FSI bus & engine generic device tree bindings4 The FSI bus is probe-able, so the OS is able to enumerate FSI slaves, and19 /* top-level of FSI bus topology, bound to an FSI master driver and20 * exposes an FSI bus */43 FSI masters66 FSI slaves91 FSI engines (devices)96 FSI device, and are passed to those FSI device drivers' ->probe() functions.110 - an FSI master111 - connected to an FSI slave[all …]
7 title: IBM FSI-attached SPI controllers13 This binding describes an FSI CFAM engine called the FSI2SPI. Therefore this14 node will always be a child of an FSI CFAM node; see fsi.txt for details on15 FSI slave and CFAM nodes. This FSI2SPI engine provides access to a number of25 - description: FSI slave address
1 Device-tree bindings for FSI-attached POWER9/POWER10 On-Chip Controller (OCC)4 This is the binding for the P9 or P10 On-Chip Controller accessed over FSI from5 a service processor. See fsi.txt for details on bindings for FSI slave and CFAM6 nodes. The OCC is not an FSI slave device itself, rather it is accessed
1 Device-tree bindings for gpio-based FSI master driver6 - clock-gpios = <gpio-descriptor>; : GPIO for FSI clock7 - data-gpios = <gpio-descriptor>; : GPIO for FSI data signal13 functions (eg, external FSI masters)
1 Device-tree bindings for AST2600 FSI master4 The AST2600 contains two identical FSI masters. They share a clock and have a18 - fsi-routing-gpios: GPIO for setting the FSI mux (internal or cabled)19 - fsi-mux-gpios: GPIO for detecting the desired FSI mux state
1 Device-tree bindings for ColdFire offloaded gpio-based FSI master driver10 - clock-gpios = <gpio-descriptor>; : GPIO for FSI clock11 - data-gpios = <gpio-descriptor>; : GPIO for FSI data signal15 functions (eg, external FSI masters)
6 Initiates a FSI master scan for all connected slave devices14 Sends an FSI BREAK command on a master's communication24 Sends an FSI terminate command from the master to its38 specified FSI bus address.46 FSI device.
6 Controls access arbitration for GPIO-based FSI master. A8 driver performs FSI bus transactions, 1 sets external mode,9 where the FSI bus is driven externally (for example, by
7 title: Renesas FIFO-buffered Serial Interface (FSI)49 description: FSI is connected by S/PDIF53 description: FSI supports 16bit stream mode57 description: FSI uses internal clock when master mode
1 Device-tree bindings for FSI-attached I2C master and busses6 - reg = < address size >; : The FSI CFAM address and address
25 tristate "SH4 FSI support"29 This option enables FSI sound support
31 established through SBE fifo on an FSI bus.
882 FSI, enumerator974 INTC_VECT(FSI, 0xF80),1041 0, 0, SCIFA5, FSI } },1070 { 0xa4080024, 0, 16, 4, /* IPRJ */ { CEU1, ETHI, FSI, SDHI1 } },
23 The P9 version of this driver is a client driver of the FSI-based OCC driver.24 It will be probed automatically by the FSI-based OCC driver.
154 /* 2nd level UICs for FSI */
340 tristate "FSI SPI driver"341 depends on FSI343 This enables support for the driver for FSI bus attached SPI
1400 tristate "FSI I2C driver"1401 depends on FSI1403 Driver for FSI bus attached I2C masters. These are I2C masters that1404 are connected to the system over an FSI bus, instead of the more
440 - `Nitrokey Start`_: Open hardware and Free Software, based on FSI
7781 FSI SUBSYSTEM7794 FSI-ATTACHED I2C DRIVER7802 FSI-ATTACHED SPI DRIVER
Completed in 44 milliseconds