Searched refs:PSI (Results 1 – 25 of 2618) sorted by relevance
12345678910>>...105
| /linux/Documentation/devicetree/bindings/dma/ti/ |
| A D | k3-pktdma.yaml | 17 PKTDMA only includes Split channels to service PSI-L based peripherals.
19 The peripherals can be PSI-L native or legacy, non PSI-L native peripherals
20 with PDMAs. PDMA is tasked to act as a bridge between the PSI-L fabric and the
36 The first cell is the PSI-L thread ID of the remote (to PKTDMA) end.
41 Please refer to the device documentation for the PSI-L thread map and also
42 the PSI-L peripheral chapter for the correct thread ID.
|
| A D | k3-bcdma.yaml | 23 Split channels can be used to service PSI-L based peripherals.
24 The peripherals can be PSI-L native or legacy, non PSI-L native peripherals
25 with PDMAs. PDMA is tasked to act as a bridge between the PSI-L fabric and the
49 PSI-L thread ID of the remote (to BCDMA) end.
54 Please refer to the device documentation for the PSI-L thread map and
55 also the PSI-L peripheral chapter for the correct thread ID.
|
| A D | k3-udma.yaml | 29 on the Rx PSI-L interface.
35 All transfers within NAVSS is done between PSI-L source and destination
37 The peripherals serviced by UDMA can be PSI-L native (sa2ul, cpsw, etc) or
38 legacy, non PSI-L native peripherals. In the later case a special, small PDMA
39 is tasked to act as a bridge between the PSI-L fabric and the legacy
53 The cell is the PSI-L thread ID of the remote (to UDMAP) end.
58 Please refer to the device documentation for the PSI-L thread map and also
59 the PSI-L peripheral chapter for the correct thread ID.
|
| /linux/Documentation/networking/devlink/ |
| A D | iosm.rst | 49 * - ``PSI RAM``
56 PSI RAM and EBL are the RAM images which are injected to the device when the
70 1) When modem is in Boot ROM stage, user can use below command to inject PSI RAM
80 3) Inject EBL after the modem is in PSI stage.
|
| /linux/Documentation/driver-api/media/drivers/ |
| A D | vidtv.rst | 144 This is the PSI generator. PSI packets contain general information
145 about a MPEG Transport Stream. A PSI generator is needed so
152 Currently vidtv supports working with 5 PSI tables: PAT, PMT,
161 debugging PSI tables. Vidtv currently tries to replicate the PSI
222 #. Inserting PSI and/or PCR packets, if needed.
349 In order to tune into a channel and read the PSI tables, we can use dvb-scan.
|
| /linux/Documentation/translations/zh_CN/accounting/ |
| A D | psi.rst | 10 PSI——压力阻塞信息
|
| /linux/drivers/gpu/drm/amd/pm/inc/ |
| A D | smu_types.h | 339 __SMU_DUMMY_MAP(PSI), \
|
| /linux/include/linux/ |
| A D | scmi_protocol.h | 356 PSI = 0x10, enumerator
|
| /linux/Documentation/accounting/ |
| A D | psi.rst | 4 PSI - Pressure Stall Information
|
| /linux/arch/powerpc/boot/dts/ |
| A D | fsp2.dts | 86 /* PSI and DMA */
|
| /linux/drivers/gpu/drm/amd/pm/swsmu/smu13/ |
| A D | yellow_carp_ppt.c | 112 FEA_MAP(PSI),
|
| /linux/kernel/printk/ |
| A D | .printk_ringbuffer.o.cmd | 333 $(wildcard include/config/PSI) \
|
| /linux/kernel/rcu/ |
| A D | .sync.o.cmd | 451 $(wildcard include/config/PSI) \
|
| /linux/lib/ |
| A D | .klist.o.cmd | 438 $(wildcard include/config/PSI) \
|
| A D | .ratelimit.o.cmd | 113 $(wildcard include/config/PSI) \
|
| /linux/kernel/locking/ |
| A D | .osq_lock.o.cmd | 320 $(wildcard include/config/PSI) \
|
| /linux/mm/ |
| A D | .page_counter.o.cmd | 278 $(wildcard include/config/PSI) \
|
| /linux/init/ |
| A D | .version.o.cmd | 96 $(wildcard include/config/PSI) \
|
| A D | .calibrate.o.cmd | 350 $(wildcard include/config/PSI) \
|
| /linux/kernel/ |
| A D | .utsname_sysctl.o.cmd | 89 $(wildcard include/config/PSI) \
|
| /linux/drivers/clk/actions/ |
| A D | .owl-reset.o.cmd | 87 $(wildcard include/config/PSI) \
|
| /linux/drivers/clk/qcom/ |
| A D | .reset.o.cmd | 433 $(wildcard include/config/PSI) \
|
| /linux/drivers/clk/sunxi-ng/ |
| A D | .ccu_reset.o.cmd | 87 $(wildcard include/config/PSI) \
|
| /linux/drivers/soc/mediatek/ |
| A D | .mtk-infracfg.o.cmd | 433 $(wildcard include/config/PSI) \
|
| /linux/drivers/soc/actions/ |
| A D | .owl-sps-helper.o.cmd | 87 $(wildcard include/config/PSI) \
|
Completed in 35 milliseconds
12345678910>>...105