Searched refs:pullups (Results 1 – 25 of 32) sorted by relevance
12
| /linux/arch/arm/boot/dts/ |
| A D | omap3-cm-t3x30.dtsi | 94 /* pullups: BIT(0) */
95 ti,pullups = <0x000001>;
|
| A D | omap4-sdp-es23plus.dts | 7 /* SDP boards with 4430 ES2.3+ or 4460 have external pullups on SCL & SDA */
|
| A D | omap4-panda-a4.dts | 10 /* Pandaboard Rev A4+ have external pullups on SCL & SDA */
|
| A D | omap4-panda-es.dts | 31 /* PandaboardES has external pullups on SCL & SDA */
|
| A D | omap3-beagle-xm.dts | 327 /* pullups: BIT(1) */
328 ti,pullups = <0x000002>;
|
| A D | omap3-tao3530.dtsi | 257 /* pullups: BIT(1) */
258 ti,pullups = <0x000002>;
|
| A D | omap3-beagle.dts | 342 /* pullups: BIT(1) */
343 ti,pullups = <0x000002>;
|
| A D | exynos5250-spring.dts | 355 * Disabled pullups since external part has its own pullups and
|
| A D | exynos5250-snow-common.dtsi | 452 * Disabled pullups since external part has its own pullups and
|
| A D | omap3-gta04.dtsi | 653 /* pullups: BIT(2) */
654 ti,pullups = <BIT(2)>;
|
| /linux/include/linux/platform_data/ |
| A D | st_sensors_pdata.h | 28 bool pullups; member
|
| /linux/drivers/gpio/ |
| A D | gpio-twl4030.c | 490 &omap_twl_info->pullups); in of_gpio_twl4030()
553 ret = gpio_twl4030_pulls(pdata->pullups, pdata->pulldowns); in gpio_twl4030_probe()
556 pdata->pullups, pdata->pulldowns, ret); in gpio_twl4030_probe()
|
| /linux/Documentation/devicetree/bindings/gpio/ |
| A D | gpio-twl4030.txt | 17 - ti,pullups : if n-th bit is set, set a pullup on GPIO-n
|
| /linux/Documentation/devicetree/bindings/iio/imu/ |
| A D | st,lsm6dsx.yaml | 60 st,pullups:
|
| /linux/Documentation/devicetree/bindings/pinctrl/ |
| A D | pinctrl-sirf.txt | 10 - sirf,pullups : if n-th bit of m-th bank is set, set a pullup on GPIO-n of bank m
|
| A D | toshiba,visconti-pinctrl.yaml | 34 configuration, pullups, drive strength.
|
| A D | pinctrl-mt8192.yaml | 60 configuration, pullups, drive strength, input enable/disable and
|
| A D | mediatek,mt65xx-pinctrl.yaml | 79 configuration, pullups, drive strength, input enable/disable and input
|
| A D | mediatek,mt6797-pinctrl.yaml | 67 configuration, pullups, drive strength, input enable/disable and input
|
| A D | mediatek,mt6779-pinctrl.yaml | 83 configuration, pullups, drive strength, input enable/disable and input schmitt.
|
| A D | st,stm32-pinctrl.yaml | 123 configuration, pullups, drive, output high/low and output speed.
|
| A D | pinctrl-mt8195.yaml | 66 configuration, pullups, drive strength, input enable/disable and
|
| A D | mediatek,mt8183-pinctrl.yaml | 78 configuration, pullups, drive strength, input enable/disable and input
|
| /linux/Documentation/spi/ |
| A D | butterfly.rst | 43 (a) flash new firmware that disables SPI (set PRR.2, and disable pullups
|
| /linux/include/linux/mfd/ |
| A D | twl.h | 592 u32 pullups; member
|
Completed in 35 milliseconds
12