1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3 * Copyright 2011, Marvell Semiconductor Inc.
4 * Lei Wen <leiwen@marvell.com>
5 *
6 * Back ported to the 8xx platform (from the 8260 platform) by
7 * Murray.Jensen@cmst.csiro.au, 27-Jan-01.
8 */
9 #ifndef __SDHCI_HW_H
10 #define __SDHCI_HW_H
11
12 #include <linux/bitops.h>
13 #include <linux/types.h>
14 #include <asm/io.h>
15 #include <mmc.h>
16 #include <asm/gpio.h>
17
18 /*
19 * Controller registers
20 */
21
22 #define SDHCI_DMA_ADDRESS 0x00
23
24 #define SDHCI_BLOCK_SIZE 0x04
25 #define SDHCI_MAKE_BLKSZ(dma, blksz) (((dma & 0x7) << 12) | (blksz & 0xFFF))
26
27 #define SDHCI_BLOCK_COUNT 0x06
28
29 #define SDHCI_ARGUMENT 0x08
30
31 #define SDHCI_TRANSFER_MODE 0x0C
32 #define SDHCI_TRNS_DMA BIT(0)
33 #define SDHCI_TRNS_BLK_CNT_EN BIT(1)
34 #define SDHCI_TRNS_ACMD12 BIT(2)
35 #define SDHCI_TRNS_READ BIT(4)
36 #define SDHCI_TRNS_MULTI BIT(5)
37
38 #define SDHCI_COMMAND 0x0E
39 #define SDHCI_CMD_RESP_MASK 0x03
40 #define SDHCI_CMD_CRC 0x08
41 #define SDHCI_CMD_INDEX 0x10
42 #define SDHCI_CMD_DATA 0x20
43 #define SDHCI_CMD_ABORTCMD 0xC0
44
45 #define SDHCI_CMD_RESP_NONE 0x00
46 #define SDHCI_CMD_RESP_LONG 0x01
47 #define SDHCI_CMD_RESP_SHORT 0x02
48 #define SDHCI_CMD_RESP_SHORT_BUSY 0x03
49
50 #define SDHCI_MAKE_CMD(c, f) (((c & 0xff) << 8) | (f & 0xff))
51 #define SDHCI_GET_CMD(c) ((c>>8) & 0x3f)
52
53 #define SDHCI_RESPONSE 0x10
54
55 #define SDHCI_BUFFER 0x20
56
57 #define SDHCI_PRESENT_STATE 0x24
58 #define SDHCI_CMD_INHIBIT BIT(0)
59 #define SDHCI_DATA_INHIBIT BIT(1)
60 #define SDHCI_DOING_WRITE BIT(8)
61 #define SDHCI_DOING_READ BIT(9)
62 #define SDHCI_SPACE_AVAILABLE BIT(10)
63 #define SDHCI_DATA_AVAILABLE BIT(11)
64 #define SDHCI_CARD_PRESENT BIT(16)
65 #define SDHCI_CARD_STATE_STABLE BIT(17)
66 #define SDHCI_CARD_DETECT_PIN_LEVEL BIT(18)
67 #define SDHCI_WRITE_PROTECT BIT(19)
68 #define SDHCI_DATA_LVL_MASK 0x00F00000
69 #define SDHCI_DATA_0_LVL_MASK BIT(20)
70
71 #define SDHCI_HOST_CONTROL 0x28
72 #define SDHCI_CTRL_LED BIT(0)
73 #define SDHCI_CTRL_4BITBUS BIT(1)
74 #define SDHCI_CTRL_HISPD BIT(2)
75 #define SDHCI_CTRL_DMA_MASK 0x18
76 #define SDHCI_CTRL_SDMA 0x00
77 #define SDHCI_CTRL_ADMA1 0x08
78 #define SDHCI_CTRL_ADMA32 0x10
79 #define SDHCI_CTRL_ADMA64 0x18
80 #define SDHCI_CTRL_8BITBUS BIT(5)
81 #define SDHCI_CTRL_CD_TEST_INS BIT(6)
82 #define SDHCI_CTRL_CD_TEST BIT(7)
83
84 #define SDHCI_POWER_CONTROL 0x29
85 #define SDHCI_POWER_ON 0x01
86 #define SDHCI_POWER_180 0x0A
87 #define SDHCI_POWER_300 0x0C
88 #define SDHCI_POWER_330 0x0E
89
90 #define SDHCI_BLOCK_GAP_CONTROL 0x2A
91
92 #define SDHCI_WAKE_UP_CONTROL 0x2B
93 #define SDHCI_WAKE_ON_INT BIT(0)
94 #define SDHCI_WAKE_ON_INSERT BIT(1)
95 #define SDHCI_WAKE_ON_REMOVE BIT(2)
96
97 #define SDHCI_CLOCK_CONTROL 0x2C
98 #define SDHCI_DIVIDER_SHIFT 8
99 #define SDHCI_DIVIDER_HI_SHIFT 6
100 #define SDHCI_DIV_MASK 0xFF
101 #define SDHCI_DIV_MASK_LEN 8
102 #define SDHCI_DIV_HI_MASK 0x300
103 #define SDHCI_PROG_CLOCK_MODE BIT(5)
104 #define SDHCI_CLOCK_CARD_EN BIT(2)
105 #define SDHCI_CLOCK_INT_STABLE BIT(1)
106 #define SDHCI_CLOCK_INT_EN BIT(0)
107
108 #define SDHCI_TIMEOUT_CONTROL 0x2E
109
110 #define SDHCI_SOFTWARE_RESET 0x2F
111 #define SDHCI_RESET_ALL 0x01
112 #define SDHCI_RESET_CMD 0x02
113 #define SDHCI_RESET_DATA 0x04
114
115 #define SDHCI_INT_STATUS 0x30
116 #define SDHCI_INT_ENABLE 0x34
117 #define SDHCI_SIGNAL_ENABLE 0x38
118 #define SDHCI_INT_RESPONSE BIT(0)
119 #define SDHCI_INT_DATA_END BIT(1)
120 #define SDHCI_INT_DMA_END BIT(3)
121 #define SDHCI_INT_SPACE_AVAIL BIT(4)
122 #define SDHCI_INT_DATA_AVAIL BIT(5)
123 #define SDHCI_INT_CARD_INSERT BIT(6)
124 #define SDHCI_INT_CARD_REMOVE BIT(7)
125 #define SDHCI_INT_CARD_INT BIT(8)
126 #define SDHCI_INT_ERROR BIT(15)
127 #define SDHCI_INT_TIMEOUT BIT(16)
128 #define SDHCI_INT_CRC BIT(17)
129 #define SDHCI_INT_END_BIT BIT(18)
130 #define SDHCI_INT_INDEX BIT(19)
131 #define SDHCI_INT_DATA_TIMEOUT BIT(20)
132 #define SDHCI_INT_DATA_CRC BIT(21)
133 #define SDHCI_INT_DATA_END_BIT BIT(22)
134 #define SDHCI_INT_BUS_POWER BIT(23)
135 #define SDHCI_INT_ACMD12ERR BIT(24)
136 #define SDHCI_INT_ADMA_ERROR BIT(25)
137
138 #define SDHCI_INT_NORMAL_MASK 0x00007FFF
139 #define SDHCI_INT_ERROR_MASK 0xFFFF8000
140
141 #define SDHCI_INT_CMD_MASK (SDHCI_INT_RESPONSE | SDHCI_INT_TIMEOUT | \
142 SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX)
143 #define SDHCI_INT_DATA_MASK (SDHCI_INT_DATA_END | SDHCI_INT_DMA_END | \
144 SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | \
145 SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_DATA_CRC | \
146 SDHCI_INT_DATA_END_BIT | SDHCI_INT_ADMA_ERROR)
147 #define SDHCI_INT_ALL_MASK ((unsigned int)-1)
148
149 #define SDHCI_ACMD12_ERR 0x3C
150
151 #define SDHCI_HOST_CONTROL2 0x3E
152 #define SDHCI_CTRL_UHS_MASK 0x0007
153 #define SDHCI_CTRL_UHS_SDR12 0x0000
154 #define SDHCI_CTRL_UHS_SDR25 0x0001
155 #define SDHCI_CTRL_UHS_SDR50 0x0002
156 #define SDHCI_CTRL_UHS_SDR104 0x0003
157 #define SDHCI_CTRL_UHS_DDR50 0x0004
158 #define SDHCI_CTRL_HS400 0x0005 /* Non-standard */
159 #define SDHCI_CTRL_VDD_180 0x0008
160 #define SDHCI_CTRL_DRV_TYPE_MASK 0x0030
161 #define SDHCI_CTRL_DRV_TYPE_B 0x0000
162 #define SDHCI_CTRL_DRV_TYPE_A 0x0010
163 #define SDHCI_CTRL_DRV_TYPE_C 0x0020
164 #define SDHCI_CTRL_DRV_TYPE_D 0x0030
165 #define SDHCI_CTRL_EXEC_TUNING 0x0040
166 #define SDHCI_CTRL_TUNED_CLK 0x0080
167 #define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000
168
169 #define SDHCI_CAPABILITIES 0x40
170 #define SDHCI_TIMEOUT_CLK_MASK 0x0000003F
171 #define SDHCI_TIMEOUT_CLK_SHIFT 0
172 #define SDHCI_TIMEOUT_CLK_UNIT 0x00000080
173 #define SDHCI_CLOCK_BASE_MASK 0x00003F00
174 #define SDHCI_CLOCK_V3_BASE_MASK 0x0000FF00
175 #define SDHCI_CLOCK_BASE_SHIFT 8
176 #define SDHCI_MAX_BLOCK_MASK 0x00030000
177 #define SDHCI_MAX_BLOCK_SHIFT 16
178 #define SDHCI_CAN_DO_8BIT BIT(18)
179 #define SDHCI_CAN_DO_ADMA2 BIT(19)
180 #define SDHCI_CAN_DO_ADMA1 BIT(20)
181 #define SDHCI_CAN_DO_HISPD BIT(21)
182 #define SDHCI_CAN_DO_SDMA BIT(22)
183 #define SDHCI_CAN_VDD_330 BIT(24)
184 #define SDHCI_CAN_VDD_300 BIT(25)
185 #define SDHCI_CAN_VDD_180 BIT(26)
186 #define SDHCI_CAN_64BIT BIT(28)
187
188 #define SDHCI_CAPABILITIES_1 0x44
189 #define SDHCI_SUPPORT_SDR50 0x00000001
190 #define SDHCI_SUPPORT_SDR104 0x00000002
191 #define SDHCI_SUPPORT_DDR50 0x00000004
192 #define SDHCI_SUPPORT_HS400 BIT(31)
193 #define SDHCI_USE_SDR50_TUNING 0x00002000
194
195 #define SDHCI_CLOCK_MUL_MASK 0x00FF0000
196 #define SDHCI_CLOCK_MUL_SHIFT 16
197
198 #define SDHCI_MAX_CURRENT 0x48
199
200 /* 4C-4F reserved for more max current */
201
202 #define SDHCI_SET_ACMD12_ERROR 0x50
203 #define SDHCI_SET_INT_ERROR 0x52
204
205 #define SDHCI_ADMA_ERROR 0x54
206
207 /* 55-57 reserved */
208
209 #define SDHCI_ADMA_ADDRESS 0x58
210 #define SDHCI_ADMA_ADDRESS_HI 0x5c
211
212 /* 60-FB reserved */
213
214 #define SDHCI_SLOT_INT_STATUS 0xFC
215
216 #define SDHCI_HOST_VERSION 0xFE
217 #define SDHCI_VENDOR_VER_MASK 0xFF00
218 #define SDHCI_VENDOR_VER_SHIFT 8
219 #define SDHCI_SPEC_VER_MASK 0x00FF
220 #define SDHCI_SPEC_VER_SHIFT 0
221 #define SDHCI_SPEC_100 0
222 #define SDHCI_SPEC_200 1
223 #define SDHCI_SPEC_300 2
224
225 #define SDHCI_GET_VERSION(x) (x->version & SDHCI_SPEC_VER_MASK)
226
227 /*
228 * End of controller registers.
229 */
230
231 #define SDHCI_MAX_DIV_SPEC_200 256
232 #define SDHCI_MAX_DIV_SPEC_300 2046
233
234 /*
235 * quirks
236 */
237 #define SDHCI_QUIRK_32BIT_DMA_ADDR (1 << 0)
238 #define SDHCI_QUIRK_REG32_RW (1 << 1)
239 #define SDHCI_QUIRK_BROKEN_R1B (1 << 2)
240 #define SDHCI_QUIRK_NO_HISPD_BIT (1 << 3)
241 #define SDHCI_QUIRK_BROKEN_VOLTAGE (1 << 4)
242 /*
243 * SDHCI_QUIRK_BROKEN_HISPD_MODE
244 * the hardware cannot operate correctly in high-speed mode,
245 * this quirk forces the sdhci host-controller to non high-speed mode
246 */
247 #define SDHCI_QUIRK_BROKEN_HISPD_MODE BIT(5)
248 #define SDHCI_QUIRK_WAIT_SEND_CMD (1 << 6)
249 #define SDHCI_QUIRK_USE_WIDE8 (1 << 8)
250 #define SDHCI_QUIRK_NO_1_8_V (1 << 9)
251 #define SDHCI_QUIRK_SUPPORT_SINGLE (1 << 10)
252 /* Capability register bit-63 indicates HS400 support */
253 #define SDHCI_QUIRK_CAPS_BIT63_FOR_HS400 BIT(11)
254
255 /* to make gcc happy */
256 struct sdhci_host;
257
258 /*
259 * Host SDMA buffer boundary. Valid values from 4K to 512K in powers of 2.
260 */
261 #define SDHCI_DEFAULT_BOUNDARY_SIZE (512 * 1024)
262 #define SDHCI_DEFAULT_BOUNDARY_ARG (7)
263 struct sdhci_ops {
264 #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
265 u32 (*read_l)(struct sdhci_host *host, int reg);
266 u16 (*read_w)(struct sdhci_host *host, int reg);
267 u8 (*read_b)(struct sdhci_host *host, int reg);
268 void (*write_l)(struct sdhci_host *host, u32 val, int reg);
269 void (*write_w)(struct sdhci_host *host, u16 val, int reg);
270 void (*write_b)(struct sdhci_host *host, u8 val, int reg);
271 #endif
272 int (*get_cd)(struct sdhci_host *host);
273 void (*set_control_reg)(struct sdhci_host *host);
274 int (*set_ios_post)(struct sdhci_host *host);
275 void (*set_clock)(struct sdhci_host *host, u32 div);
276 int (*platform_execute_tuning)(struct mmc *host, u8 opcode);
277 int (*set_delay)(struct sdhci_host *host);
278 /* Callback function to set DLL clock configuration */
279 int (*config_dll)(struct sdhci_host *host, u32 clock, bool enable);
280 int (*deferred_probe)(struct sdhci_host *host);
281
282 /**
283 * set_enhanced_strobe() - Set HS400 Enhanced Strobe config
284 *
285 * This is called after setting the card speed and mode to
286 * HS400 ES, and should set any host-specific configuration
287 * necessary for it.
288 *
289 * @host: SDHCI host structure
290 * Return: 0 if successful, -ve on error
291 */
292 int (*set_enhanced_strobe)(struct sdhci_host *host);
293 };
294
295 #define ADMA_MAX_LEN 65532
296 #ifdef CONFIG_DMA_ADDR_T_64BIT
297 #define ADMA_DESC_LEN 16
298 #else
299 #define ADMA_DESC_LEN 8
300 #endif
301 #define ADMA_TABLE_NO_ENTRIES (CONFIG_SYS_MMC_MAX_BLK_COUNT * \
302 MMC_MAX_BLOCK_LEN) / ADMA_MAX_LEN
303
304 #define ADMA_TABLE_SZ (ADMA_TABLE_NO_ENTRIES * ADMA_DESC_LEN)
305
306 /* Decriptor table defines */
307 #define ADMA_DESC_ATTR_VALID BIT(0)
308 #define ADMA_DESC_ATTR_END BIT(1)
309 #define ADMA_DESC_ATTR_INT BIT(2)
310 #define ADMA_DESC_ATTR_ACT1 BIT(4)
311 #define ADMA_DESC_ATTR_ACT2 BIT(5)
312
313 #define ADMA_DESC_TRANSFER_DATA ADMA_DESC_ATTR_ACT2
314 #define ADMA_DESC_LINK_DESC (ADMA_DESC_ATTR_ACT1 | ADMA_DESC_ATTR_ACT2)
315
316 struct sdhci_adma_desc {
317 u8 attr;
318 u8 reserved;
319 u16 len;
320 u32 addr_lo;
321 #ifdef CONFIG_DMA_ADDR_T_64BIT
322 u32 addr_hi;
323 #endif
324 } __packed;
325
326 struct sdhci_host {
327 const char *name;
328 void *ioaddr;
329 unsigned int quirks;
330 unsigned int host_caps;
331 unsigned int version;
332 unsigned int max_clk; /* Maximum Base Clock frequency */
333 unsigned int clk_mul; /* Clock Multiplier value */
334 unsigned int clock;
335 struct mmc *mmc;
336 const struct sdhci_ops *ops;
337 int index;
338
339 int bus_width;
340 struct gpio_desc pwr_gpio; /* Power GPIO */
341 struct gpio_desc cd_gpio; /* Card Detect GPIO */
342
343 uint voltages;
344
345 struct mmc_config cfg;
346 void *align_buffer;
347 bool force_align_buffer;
348 dma_addr_t start_addr;
349 int flags;
350 #define USE_SDMA (0x1 << 0)
351 #define USE_ADMA (0x1 << 1)
352 #define USE_ADMA64 (0x1 << 2)
353 #define USE_DMA (USE_SDMA | USE_ADMA | USE_ADMA64)
354 dma_addr_t adma_addr;
355 #if CONFIG_IS_ENABLED(MMC_SDHCI_ADMA)
356 struct sdhci_adma_desc *adma_desc_table;
357 #endif
358 };
359
360 #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
361
sdhci_writel(struct sdhci_host * host,u32 val,int reg)362 static inline void sdhci_writel(struct sdhci_host *host, u32 val, int reg)
363 {
364 if (unlikely(host->ops->write_l))
365 host->ops->write_l(host, val, reg);
366 else
367 writel(val, host->ioaddr + reg);
368 }
369
sdhci_writew(struct sdhci_host * host,u16 val,int reg)370 static inline void sdhci_writew(struct sdhci_host *host, u16 val, int reg)
371 {
372 if (unlikely(host->ops->write_w))
373 host->ops->write_w(host, val, reg);
374 else
375 writew(val, host->ioaddr + reg);
376 }
377
sdhci_writeb(struct sdhci_host * host,u8 val,int reg)378 static inline void sdhci_writeb(struct sdhci_host *host, u8 val, int reg)
379 {
380 if (unlikely(host->ops->write_b))
381 host->ops->write_b(host, val, reg);
382 else
383 writeb(val, host->ioaddr + reg);
384 }
385
sdhci_readl(struct sdhci_host * host,int reg)386 static inline u32 sdhci_readl(struct sdhci_host *host, int reg)
387 {
388 if (unlikely(host->ops->read_l))
389 return host->ops->read_l(host, reg);
390 else
391 return readl(host->ioaddr + reg);
392 }
393
sdhci_readw(struct sdhci_host * host,int reg)394 static inline u16 sdhci_readw(struct sdhci_host *host, int reg)
395 {
396 if (unlikely(host->ops->read_w))
397 return host->ops->read_w(host, reg);
398 else
399 return readw(host->ioaddr + reg);
400 }
401
sdhci_readb(struct sdhci_host * host,int reg)402 static inline u8 sdhci_readb(struct sdhci_host *host, int reg)
403 {
404 if (unlikely(host->ops->read_b))
405 return host->ops->read_b(host, reg);
406 else
407 return readb(host->ioaddr + reg);
408 }
409
410 #else
411
sdhci_writel(struct sdhci_host * host,u32 val,int reg)412 static inline void sdhci_writel(struct sdhci_host *host, u32 val, int reg)
413 {
414 writel(val, host->ioaddr + reg);
415 }
416
sdhci_writew(struct sdhci_host * host,u16 val,int reg)417 static inline void sdhci_writew(struct sdhci_host *host, u16 val, int reg)
418 {
419 writew(val, host->ioaddr + reg);
420 }
421
sdhci_writeb(struct sdhci_host * host,u8 val,int reg)422 static inline void sdhci_writeb(struct sdhci_host *host, u8 val, int reg)
423 {
424 writeb(val, host->ioaddr + reg);
425 }
sdhci_readl(struct sdhci_host * host,int reg)426 static inline u32 sdhci_readl(struct sdhci_host *host, int reg)
427 {
428 return readl(host->ioaddr + reg);
429 }
430
sdhci_readw(struct sdhci_host * host,int reg)431 static inline u16 sdhci_readw(struct sdhci_host *host, int reg)
432 {
433 return readw(host->ioaddr + reg);
434 }
435
sdhci_readb(struct sdhci_host * host,int reg)436 static inline u8 sdhci_readb(struct sdhci_host *host, int reg)
437 {
438 return readb(host->ioaddr + reg);
439 }
440 #endif
441
442 #ifdef CONFIG_BLK
443 /**
444 * sdhci_setup_cfg() - Set up the configuration for DWMMC
445 *
446 * This is used to set up an SDHCI device when you are using CONFIG_BLK.
447 *
448 * This should be called from your MMC driver's probe() method once you have
449 * the information required.
450 *
451 * Generally your driver will have a platform data structure which holds both
452 * the configuration (struct mmc_config) and the MMC device info (struct mmc).
453 * For example:
454 *
455 * struct msm_sdhc_plat {
456 * struct mmc_config cfg;
457 * struct mmc mmc;
458 * };
459 *
460 * ...
461 *
462 * Inside U_BOOT_DRIVER():
463 * .plat_auto = sizeof(struct msm_sdhc_plat),
464 *
465 * To access platform data:
466 * struct msm_sdhc_plat *plat = dev_get_plat(dev);
467 *
468 * See msm_sdhci.c for an example.
469 *
470 * @cfg: Configuration structure to fill in (generally &plat->mmc)
471 * @host: SDHCI host structure
472 * @f_max: Maximum supported clock frequency in HZ (0 for default)
473 * @f_min: Minimum supported clock frequency in HZ (0 for default)
474 */
475 int sdhci_setup_cfg(struct mmc_config *cfg, struct sdhci_host *host,
476 u32 f_max, u32 f_min);
477
478 /**
479 * sdhci_bind() - Set up a new MMC block device
480 *
481 * This is used to set up an SDHCI block device when you are using CONFIG_BLK.
482 * It should be called from your driver's bind() method.
483 *
484 * See msm_sdhci.c for an example.
485 *
486 * @dev: Device to set up
487 * @mmc: Pointer to mmc structure (normally &plat->mmc)
488 * @cfg: Empty configuration structure (generally &plat->cfg). This is
489 * normally all zeroes at this point. The only purpose of passing
490 * this in is to set mmc->cfg to it.
491 * Return: 0 if OK, -ve if the block device could not be created
492 */
493 int sdhci_bind(struct udevice *dev, struct mmc *mmc, struct mmc_config *cfg);
494 #else
495
496 /**
497 * add_sdhci() - Add a new SDHCI interface
498 *
499 * This is used when you are not using CONFIG_BLK. Convert your driver over!
500 *
501 * @host: SDHCI host structure
502 * @f_max: Maximum supported clock frequency in HZ (0 for default)
503 * @f_min: Minimum supported clock frequency in HZ (0 for default)
504 * Return: 0 if OK, -ve on error
505 */
506 int add_sdhci(struct sdhci_host *host, u32 f_max, u32 f_min);
507 #endif /* !CONFIG_BLK */
508
509 void sdhci_set_uhs_timing(struct sdhci_host *host);
510 #ifdef CONFIG_DM_MMC
511 /* Export the operations to drivers */
512 int sdhci_probe(struct udevice *dev);
513 int sdhci_set_clock(struct mmc *mmc, unsigned int clock);
514
515 /**
516 * sdhci_set_control_reg - Set control registers
517 *
518 * This is used set up control registers for voltage level and UHS speed
519 * mode.
520 *
521 * @host: SDHCI host structure
522 */
523 void sdhci_set_control_reg(struct sdhci_host *host);
524 extern const struct dm_mmc_ops sdhci_ops;
525 #else
526 #endif
527
528 struct sdhci_adma_desc *sdhci_adma_init(void);
529 void sdhci_prepare_adma_table(struct sdhci_adma_desc *table,
530 struct mmc_data *data, dma_addr_t addr);
531
532 #endif /* __SDHCI_HW_H */
533