Searched refs:PSI (Results 1 – 20 of 20) sorted by relevance

/linux/Documentation/devicetree/bindings/dma/ti/
A D	k3-pktdma.yaml	17 PKTDMA only includes Split channels to service PSI-L based peripherals. 19 The peripherals can be PSI-L native or legacy, non PSI-L native peripherals 20 with PDMAs. PDMA is tasked to act as a bridge between the PSI-L fabric and the 37 The first cell is the PSI-L thread ID of the remote (to PKTDMA) end. 42 Please refer to the device documentation for the PSI-L thread map and also 43 the PSI-L peripheral chapter for the correct thread ID.
A D	k3-udma.yaml	29 on the Rx PSI-L interface. 35 All transfers within NAVSS is done between PSI-L source and destination 37 The peripherals serviced by UDMA can be PSI-L native (sa2ul, cpsw, etc) or 38 legacy, non PSI-L native peripherals. In the later case a special, small PDMA 39 is tasked to act as a bridge between the PSI-L fabric and the legacy 54 The cell is the PSI-L thread ID of the remote (to UDMAP) end. 59 Please refer to the device documentation for the PSI-L thread map and also 60 the PSI-L peripheral chapter for the correct thread ID.
A D	k3-bcdma.yaml	23 Split channels can be used to service PSI-L based peripherals. 24 The peripherals can be PSI-L native or legacy, non PSI-L native peripherals 25 with PDMAs. PDMA is tasked to act as a bridge between the PSI-L fabric and the 57 PSI-L thread ID of the remote (to BCDMA) end. 62 Please refer to the device documentation for the PSI-L thread map and 63 also the PSI-L peripheral chapter for the correct thread ID.
/linux/Documentation/networking/devlink/
A D	iosm.rst	49 * - ``PSI RAM`` 56 PSI RAM and EBL are the RAM images which are injected to the device when the 70 1) When modem is in Boot ROM stage, user can use below command to inject PSI RAM 80 3) Inject EBL after the modem is in PSI stage.
/linux/Documentation/driver-api/media/drivers/
A D	vidtv.rst	144 This is the PSI generator. PSI packets contain general information 145 about a MPEG Transport Stream. A PSI generator is needed so 152 Currently vidtv supports working with 5 PSI tables: PAT, PMT, 161 debugging PSI tables. Vidtv currently tries to replicate the PSI 222 #. Inserting PSI and/or PCR packets, if needed. 349 In order to tune into a channel and read the PSI tables, we can use dvb-scan.
/linux/Documentation/devicetree/bindings/media/
A D	ti,j721e-csi2rx-shim.yaml	11 enables sending captured frames to memory over PSI-L DMA. In the J721E
/linux/Documentation/translations/zh_CN/accounting/
A D	psi.rst	10 PSI——压力阻塞信息
/linux/drivers/gpu/drm/amd/pm/swsmu/inc/
A D	smu_types.h	390 __SMU_DUMMY_MAP(PSI), \
/linux/Documentation/accounting/
A D	psi.rst	4 PSI - Pressure Stall Information
/linux/include/linux/
A D	scmi_protocol.h	413 PSI = 0x10, enumerator
/linux/arch/powerpc/boot/dts/
A D	fsp2.dts	86 /* PSI and DMA */
/linux/Documentation/admin-guide/mm/damon/
A D	reclaim.rst	127 memory pressure is incurred. System-wide ``some`` memory PSI in microseconds
/linux/drivers/gpu/drm/amd/pm/swsmu/smu13/
A D	smu_v13_0_4_ppt.c	130 FEA_MAP(PSI),
A D	yellow_carp_ppt.c	125 FEA_MAP(PSI),
/linux/drivers/gpu/drm/amd/pm/swsmu/smu14/
A D	smu_v14_0_0_ppt.c	165 FEA_MAP(PSI),
/linux/Documentation/admin-guide/
A D	cgroup-v2.rst	1039 Writing "0" to the file will disable the cgroup PSI accounting. 1040 Writing "1" to the file will re-enable the cgroup PSI accounting. 1042 This control attribute is not hierarchical, so disable or enable PSI 1043 accounting in a cgroup does not affect PSI accounting in descendants 1046 The reason this control attribute exists is that PSI accounts stalls for 1050 be used to disable PSI accounting in the non-leaf cgroups.
/linux/Documentation/mm/damon/
A D	design.rst	454 time (PSI) could be examples. Note that users should explicitly set
/linux/drivers/gpu/drm/amd/pm/swsmu/smu11/
A D	vangogh_ppt.c	168 FEA_MAP(PSI),
/linux/init/
A D	Kconfig	653 config PSI config 676 depends on PSI
/linux/
A D	MAINTAINERS	18492 PRESSURE STALL INFORMATION (PSI)

Completed in 65 milliseconds

Last Index update Fri Aug 22 08:59:00 CST 2025