| /linux/drivers/gpu/drm/amd/display/modules/inc/ |
| A D | mod_info_packet.h | 68 struct frame_duration_op decrease; member
|
| /linux/drivers/gpu/drm/amd/display/modules/info_packet/ |
| A D | info_packet.c | 575 info_packet->sb[4] = (param->increase.support << 6 | param->decrease.support << 7); in mod_build_adaptive_sync_infopacket_v2()
577 info_packet->sb[6] = param->decrease.frame_duration_hex; in mod_build_adaptive_sync_infopacket_v2()
|
| /linux/Documentation/devicetree/bindings/input/ |
| A D | iqs626a.yaml | 189 azoteq,meas-cap-decrease:
455 channel in response to a decrease in counts. Node names suffixed with
459 that only events corresponding to a decrease in counts are reported
463 the counts increase or decrease such that events of either direction
527 azoteq,meas-cap-decrease:
766 azoteq,meas-cap-decrease;
861 azoteq,meas-cap-decrease;
869 azoteq,meas-cap-decrease;
|
| A D | iqs269a.yaml | 333 azoteq,meas-cap-decrease:
449 a decrease in counts. Node names suffixed with '-alt' instead corre-
453 that only events corresponding to a decrease in counts are reported
457 the counts increase or decrease such that events of either direction
|
| /linux/Documentation/devicetree/bindings/net/wireless/ |
| A D | ieee80211.yaml | 30 decrease performance noticeably
|
| /linux/Documentation/devicetree/bindings/thermal/ |
| A D | qcom-spmi-adc-tm5.yaml | 49 description: This parameter is used to decrease ADC sampling rate.
114 description: This parameter is used to decrease ADC sampling rate.
|
| A D | qcom-spmi-adc-tm-hc.yaml | 45 description: This parameter is used to decrease ADC sampling rate.
|
| /linux/arch/arm/boot/dts/intel/socfpga/ |
| A D | socfpga_arria5_socdk.dts | 92 * adjust the falling times to decrease the i2c frequency to 50Khz
|
| A D | socfpga_cyclone5_socdk.dts | 96 * adjust the falling times to decrease the i2c frequency to 50Khz
|
| A D | socfpga_arria10_socdk.dtsi | 131 * adjust the falling times to decrease the i2c frequency to 50Khz
|
| /linux/drivers/ras/ |
| A D | Kconfig | 22 a failed system increases, then availability will decrease.
|
| /linux/Documentation/hwmon/ |
| A D | sht15.rst | 51 measurement and decrease power consumption, while losing on precision.
|
| A D | w83793.rst | 91 if tempX_input < thermal_cruiseX - toleranceX, the chip will decrease
|
| /linux/Documentation/leds/ |
| A D | leds-mt6370-rgb.rst | 16 can increase or decrease the brightness of the RGB LED via an I2C interface.
|
| /linux/Documentation/devicetree/bindings/power/supply/ |
| A D | richtek,rt9455.yaml | 47 input voltage level in uV, used to decrease voltage level when the over current of the
|
| /linux/Documentation/sound/soc/ |
| A D | pops-clicks.rst | 52 is heard when the gain increase or decrease changes the mean audio signal
|
| /linux/Documentation/scheduler/ |
| A D | schedutil.rst | 39 will decrease to reflect the fraction of time each task spends on the CPU
102 highest. UTIL_EST filters to instantly increase and only decay on decrease.
|
| /linux/fs/ocfs2/ |
| A D | Kconfig | 78 this option for debugging only as it is likely to decrease
|
| /linux/arch/arm/boot/dts/st/ |
| A D | stm32mp135f-dhcor-dhsbc.dts | 387 st,decrease-hs-slew-rate;
405 st,decrease-hs-slew-rate;
|
| A D | stm32mp135f-dk.dts | 528 st,decrease-hs-slew-rate;
542 st,decrease-hs-slew-rate;
|
| /linux/drivers/net/ethernet/wiznet/ |
| A D | Kconfig | 70 Performance may decrease compared to explicitly selected bus mode.
|
| /linux/arch/mips/cavium-octeon/ |
| A D | Kconfig | 10 workarounds will cause a slight decrease in performance on
|
| /linux/arch/sparc/lib/ |
| A D | M7memcpy.S | 278 sub %o2, 16, %o2 ! decrease count by 16
291 subcc %o2, 8, %o2 ! decrease count by 8
372 subcc %o2, 8, %o2 ! decrease count by 8
386 subcc %o2, 4, %o2 ! decrease count by 4
618 subcc %o3, 8, %o3 ! decrease count by 8
|
| /linux/Documentation/devicetree/bindings/iio/adc/ |
| A D | qcom,pm8018-adc.yaml | 84 This parameter is used to decrease the ADC sampling rate.
|
| /linux/Documentation/networking/ |
| A D | net_dim.rst | 52 compared in a similar fashion - increase == "better" and decrease == "worse".
55 increase in the interrupt rate is considered "worse" and a decrease is
|