Searched refs:operate (Results 1 – 25 of 252) sorted by relevance
1234567891011
| /linux/Documentation/arch/mips/ |
| A D | ingenic-tcu.rst | 29 operate.
35 - On the oldest SoCs (up to JZ4740), all of the eight channels operate in
37 - On JZ4725B, channel 5 operates as TCU2, the others operate as TCU1.
38 - On newest SoCs (JZ4750 and above), channels 1-2 operate as TCU2, the
39 others operate as TCU1.
|
| /linux/Documentation/devicetree/bindings/phy/ |
| A D | microchip,sparx5-serdes.yaml | 31 The SERDES6G is a high-speed SERDES interface, which can operate at
41 The SERDES10G is a high-speed SERDES interface, which can operate at
54 The SERDES25G is a high-speed SERDES interface, which can operate at
|
| /linux/drivers/firmware/arm_scmi/transports/ |
| A D | Kconfig | 57 If you want the SCMI SMC based transport to operate in atomic
61 transport to optionally ask for atomic SCMI transactions and operate
114 If you want the SCMI VirtIO based transport to operate in atomic
119 transport to optionally ask for atomic SCMI transactions and operate
|
| /linux/Documentation/devicetree/bindings/power/supply/ |
| A D | qcom,pm8941-charger.yaml | 54 Battery voltage limit in uV above which fast charging may operate; Defaults to 3.2V
55 Below this value linear or switch-mode auto-trickle-charging will operate.
62 Battery voltage limit in uV below which fast charging may operate; Defaults to 4.2V
98 Input voltage level in uV above which charging may operate. Defaults to 4.3V.
|
| A D | battery.yaml | 107 - description: minimum temperature at which battery can operate
108 - description: maximum temperature at which battery can operate
|
| /linux/Documentation/devicetree/bindings/iio/temperature/ |
| A D | melexis,mlx90632.yaml | 20 operate and measure ambient temperature in range of -20 to 85 degrees
37 operate and measure ambient temperature in range of -20 to 85 degrees
|
| /linux/Documentation/devicetree/bindings/mtd/ |
| A D | microchip,mchp23k256.txt | 8 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
|
| /linux/drivers/dma/amd/ |
| A D | Kconfig | 12 operate on instructions (descriptors) provided by the host operating
|
| /linux/Documentation/arch/sh/ |
| A D | booting.rst | 9 inter-operate with old bootloaders must either use a builtin DTB or
|
| /linux/Documentation/scsi/ |
| A D | bnx2fc.rst | 13 depend on the state of the network interfaces to operate. As such, the network
28 2. Configure the interfaces on which bnx2fc driver has to operate on.
|
| /linux/Documentation/devicetree/bindings/ipmi/ |
| A D | aspeed,ast2400-ibt-bmc.txt | 19 interrupt, the driver will operate in poll mode.
|
| /linux/drivers/pci/endpoint/ |
| A D | Kconfig | 14 controller that can operate in endpoint mode.
|
| /linux/drivers/usb/dwc2/ |
| A D | Kconfig | 35 driver to operate in Host-only mode.
45 driver to operate in Peripheral-only mode. This option requires
|
| /linux/Documentation/devicetree/bindings/timer/ |
| A D | ti,keystone-timer.txt | 6 timers, each half can operate in conjunction (chain mode) or independently
|
| A D | ti,da830-timer.yaml | 15 32-bit timers. When configured as dual 32-bit timers, each half can operate
|
| A D | renesas,ostm.yaml | 15 can operate in either interval count down timer or free-running compare match
|
| /linux/Documentation/driver-api/ |
| A D | mailbox.rst | 43 The client might want to operate in blocking mode (synchronously
106 dc_sync->cl.tx_done = NULL; /* operate in blocking mode */
|
| /linux/fs/sysfs/ |
| A D | Kconfig | 16 Some system agents rely on the information in sysfs to operate.
|
| /linux/Documentation/devicetree/bindings/sound/ |
| A D | qcom,q6usb.yaml | 37 on the platform, it will operate on a specific XHCI interrupter.
|
| A D | starfive,jh7110-tdm.yaml | 12 audio over a serial interface. The TDM controller can operate both
|
| /linux/Documentation/arch/x86/ |
| A D | shstk.rst | 59 are only supported in 64 bit user applications. These operate on the features
65 Enable a single feature specified in 'feature'. Can only operate on
69 Disable a single feature specified in 'feature'. Can only operate on
|
| /linux/Documentation/devicetree/bindings/net/can/ |
| A D | tcan4x5x.txt | 15 operate at should be less than or equal to 18 MHz.
|
| /linux/Documentation/devicetree/bindings/w1/ |
| A D | w1-uart.yaml | 16 The UART peripheral must support full-duplex and operate in open-drain
|
| /linux/Documentation/mm/damon/ |
| A D | index.rst | 18 Using this framework, therefore, the kernel can operate system in an
|
| /linux/Documentation/devicetree/bindings/cpufreq/ |
| A D | cpufreq-st.txt | 7 the DT and operate in the usual way.
|
Completed in 26 milliseconds
1234567891011