Searched refs:configure (Results 1 – 25 of 178) sorted by relevance
12345678
| /u-boot/board/keymile/scripts/ |
| A D | README | 5 To load and configure these usecase, two environment variables in the u-boot
7 run develop : setup environment to configure for rootfs via nfs
8 run ramfs : setup environment to configure for rootfs in ram
|
| A D | develop-arm.txt | 1 …oad_addr_r} scripts/develop-common.txt && env import -t ${load_addr_r} ${filesize} && run configure
|
| A D | develop-ppc_82xx.txt | 1 …oad_addr_r} scripts/develop-common.txt && env import -t ${load_addr_r} ${filesize} && run configure
|
| A D | develop-ppc_8xx.txt | 1 …oad_addr_r} scripts/develop-common.txt && env import -t ${load_addr_r} ${filesize} && run configure
|
| A D | ramfs-arm.txt | 1 …{load_addr_r} scripts/ramfs-common.txt && env import -t ${load_addr_r} ${filesize} && run configure
|
| A D | ramfs-ppc_82xx.txt | 1 …{load_addr_r} scripts/ramfs-common.txt && env import -t ${load_addr_r} ${filesize} && run configure
|
| A D | ramfs-ppc_8xx.txt | 1 …{load_addr_r} scripts/ramfs-common.txt && env import -t ${load_addr_r} ${filesize} && run configure
|
| /u-boot/drivers/pinctrl/nxp/ |
| A D | Kconfig | 19 property and configure related registers.
33 property and configure related registers.
47 property and configure related registers.
60 only parses the 'fsl,pins' property and configure related
74 only parses the 'fsl,pins' property and configure related
102 only parses the 'fsl,pins' property and configure related
115 only parses the 'fsl,pins' property and configure related
139 only parses the 'fsl,pins' property and configure related
154 property and configure related registers.
|
| /u-boot/doc/usage/cmd/ |
| A D | blkcache.rst | 13 blkcache configure <blocks> <entries>
27 configure
55 => blkcache configure 16 64
|
| /u-boot/arch/arm/dts/ |
| A D | twl4030_omap3.dtsi | 17 * to the SYS_NIRQ line on OMAP. Therefore, configure the
30 * pins we need to configure I2C4, or else use the legacy sys_nvmode1 and
|
| A D | twl6030_omap4.dtsi | 11 * Therefore, configure the defaults for the SYS_NIRQ1 and
|
| /u-boot/doc/device-tree-bindings/gpio/ |
| A D | intel,x86-pinctrl.txt | 11 - pad-offset - (required) offset in the IOBASE for the pin to configure
13 - offset in the GPIOBASE for the pin to configure
|
| /u-boot/board/freescale/vf610twr/ |
| A D | imximage.cfg | 5 * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
|
| /u-boot/board/toradex/colibri_vf/ |
| A D | imximage.cfg | 5 * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
|
| /u-boot/drivers/phy/ti/ |
| A D | Kconfig | 6 SoC. WIZ is a serdes wrapper used to configure some of the input
|
| /u-boot/board/phytec/pcm052/ |
| A D | imximage.cfg | 5 * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
|
| /u-boot/board/freescale/imx8qxp_mek/ |
| A D | imximage.cfg | 5 * Refer doc/imx/mkimage/imx8image.txt for more details about how-to configure
|
| /u-boot/board/freescale/p2041rdb/ |
| A D | pbi.cfg | 4 # Refer doc/README.pblimage for more details about how-to configure
|
| /u-boot/doc/device-tree-bindings/video/tilcdc/ |
| A D | panel.txt | 5 - panel-info: configuration info to configure LCDC correctly for the panel
26 - pinctrl-names, pinctrl-0: the pincontrol settings to configure
|
| /u-boot/board/siemens/capricorn/ |
| A D | imximage.cfg | 5 * Refer doc/imx/mkimage/imx8image.txt for more details about how-to configure
|
| /u-boot/board/freescale/t208xrdb/ |
| A D | t2080_pbi.cfg | 6 # Refer doc/README.pblimage for more details about how-to configure
|
| /u-boot/board/freescale/t208xqds/ |
| A D | t208x_pbi.cfg | 6 # Refer doc/README.pblimage for more details about how-to configure
|
| /u-boot/doc/ |
| A D | README.boston | 23 $ ./configure --target-list=mips64el-softmmu
31 therefore need to configure U-Boot to build for MIPSr6 in order to obtain a
|
| /u-boot/board/tq/tqma6/ |
| A D | clocks.cfg | 6 * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
|
| /u-boot/board/boundary/nitrogen6x/ |
| A D | nitrogen6dl.cfg | 5 * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
|
Completed in 40 milliseconds
12345678