Searched refs:correct (Results 1 – 25 of 127) sorted by relevance
123456
| /u-boot/test/common/ |
| A D | test_autoboot.c | 17 bool correct) in check_for_input() argument
33 if (!correct) in check_for_input()
|
| /u-boot/doc/board/anbernic/ |
| A D | rgxx3.rst | 14 The correct device is detected automatically by comparing ADC values
18 "board", "board_name", and "fdtfile" are set to the correct values
20 with the correct device tree.
|
| /u-boot/doc/ |
| A D | README.sha1 | 19 check, if the SHA1 sum from the Image stored in Flash is correct
52 Now you have a U-Boot-Image for the pcs440ep board with the correct SHA1 sum.
55 which will be found in ../current/ipam390/ - the correct SHA1 sum will be
|
| A D | README.multi-dtb-fit | 14 u-boot.bin so that U-Boot can locate it and select the correct DTB from inside
29 that SPL can locate it and select the correct DTB from inside the FIT.
36 The SPL uses board_fit_config_name_match() to find the correct DTB within the
|
| A D | README.atmel_pmecc | 8 generate ECC to correct 2, 4, 8, 12 or 24 bits of error per sector (512 or
49 correct value. This feature can also be used to setup a boot.bin for MMC boot.
|
| /u-boot/board/kobol/helios4/ |
| A D | README | 17 Please use the correct device node for your setup instead
43 Use the correct UART device node for /dev/ttyUSBX.
|
| /u-boot/board/out4/o4-imx6ull-nano/ |
| A D | Kconfig | 18 Please choose correct memory model here.
40 Please choose correct main board model here.
|
| /u-boot/doc/usage/fit/ |
| A D | update_uboot.rst | 6 Make sure the flashing addresses ('load' prop) is correct for your board!
|
| /u-boot/drivers/mtd/nand/raw/ |
| A D | nand_spl_simple.c | 160 this->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); in nand_read_page()
200 this->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); in nand_read_page()
221 nand_chip.ecc.correct = nand_correct_data; in nand_init()
|
| /u-boot/arch/arm/dts/ |
| A D | rk3566-anbernic-rgxx3.dts | 12 * set the correct dtb name for loading mainline Linux automatically.
|
| A D | bcm2835.dtsi | 34 /* enable thermal sensor with the correct compatible property set */
|
| A D | zynq-syzygy-hub.dts | 58 compatible = "atmel,24c08"; /* not sure if this is correct */
|
| A D | rk3368-px5-evb-u-boot.dtsi | 18 * PX5-evb(2GB) need to use CBRD mode, or else the dram is not correct
|
| A D | bcm2836.dtsi | 88 /* enable thermal sensor with the correct compatible property set */
|
| /u-boot/test/py/tests/test_efi_capsule/ |
| A D | uboot_bin_env.its | 3 * Make sure the flashing addresses ('load' prop) is correct for your board!
|
| /u-boot/board/sunxi/ |
| A D | Kconfig | 11 This is usually the correct option to choose.
|
| /u-boot/lib/crypt/ |
| A D | Kconfig | 8 console is correct or not.
|
| /u-boot/arch/arm/mach-rockchip/rk3568/ |
| A D | Kconfig | 17 and RG503. The correct device tree name will automatically
|
| /u-boot/board/solidrun/clearfog/ |
| A D | README | 17 Please use the correct device node for your setup instead
71 Use the correct UART device node for /dev/ttyUSBX.
|
| /u-boot/doc/usage/cmd/ |
| A D | conitrace.rst | 14 The conitrace command is used to test the correct function of the console input
|
| /u-boot/lib/efi/ |
| A D | Kconfig | 36 the correct type for EFI to load it correctly. If you are using
54 the correct type for EFI to load it correctly. If you are using
|
| /u-boot/doc/board/AndesTech/ |
| A D | adp-ag101p.rst | 34 1. Prepare the toolchains and make sure the $PATH to toolchains is correct.
|
| /u-boot/doc/board/mediatek/ |
| A D | mt7621.rst | 32 Select the correct DDR timing parameters for your board. The size shown here
|
| /u-boot/scripts/coccinelle/misc/ |
| A D | badty.cocci | 74 msg="WARNING: Use correct pointer type argument for sizeof"
|
| /u-boot/arch/arm/mach-sunxi/ |
| A D | cpu_info.c | 107 #warning Please update cpu_info.c with correct CPU information in print_cpuinfo()
|
Completed in 34 milliseconds
123456