menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"

    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (W25Q64 spi2)"
        select BSP_USING_SPI
        select BSP_USING_SPI2
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

    config BSP_USING_EEPROM
        bool "Enable I2C EEPROM (i2c1)"
        select BSP_USING_I2C
        select BSP_USING_I2C1
        default n

    config BSP_USING_RGB
        bool "Enable RGB LED (timer10/11/13 channel2)"
        select RT_USING_PWM
        select BSP_USING_PWM
        select BSP_USING_PWM10
        select BSP_USING_PWM10_CH1
        select BSP_USING_PWM11
        select BSP_USING_PWM11_CH1
        select BSP_USING_PWM13
        select BSP_USING_PWM13_CH1
        default n
endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_STM32_UART_V1_TX_TIMEOUT
                int "UART TX timeout"
                default 2000
                depends on RT_USING_SERIAL_V1
                
            menuconfig BSP_USING_UART1
                bool "Enable UART1"
                default y
                if BSP_USING_UART1
                    config BSP_UART1_RX_USING_DMA
                        bool "Enable UART1 RX DMA"
                        depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART1_TX_USING_DMA
                        bool "Enable UART1 TX DMA"
                        depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART1_RX_BUFSIZE
                        int "Set UART1 RX buffer size"
                        range 64 65535
                        depends on RT_USING_SERIAL_V2
                        default 256

                    config BSP_UART1_TX_BUFSIZE
                        int "Set UART1 TX buffer size"
                        range 0 65535
                        depends on RT_USING_SERIAL_V2
                        default 0
                    
                    config BSP_UART1_DMA_PING_BUFSIZE
                        int "Set UART1 RX DMA ping-pong buffer size"
                        range 32 65535
                        depends on RT_USING_SERIAL_V2 && BSP_UART1_RX_USING_DMA
                        default 64    
                endif
        endif

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n
        endif

    menuconfig BSP_USING_I2C
        bool "Enable I2C BUS"
        default n
        select RT_USING_I2C
        if BSP_USING_I2C
            config BSP_USING_I2C1
                bool "Enable I2C1 BUS"
                default n

            config BSP_USING_I2C2
                bool "Enable I2C2 BUS"
                default n
        endif

    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM6
                bool "Enable TIM6"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM10
            bool "Enable timer10 output PWM"
            default n
            if BSP_USING_PWM10
                config BSP_USING_PWM10_CH1
                    bool "Enable PWM10 channel1"
                    default n
            endif

        menuconfig BSP_USING_PWM11
            bool "Enable timer11 output PWM"
            default n
            if BSP_USING_PWM11
                config BSP_USING_PWM11_CH1
                    bool "Enable PWM11 channel1"
                    default n
            endif

        menuconfig BSP_USING_PWM13
            bool "Enable timer13 output PWM"
            default n
            if BSP_USING_PWM13
                config BSP_USING_PWM13_CH1
                    bool "Enable PWM13 channel1"
                    default n
            endif
        endif

    source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu