| /bsp/allwinner/libraries/sunxi-hal/hal/source/uart/platform/ |
| A D | uart-sun8iw20.h | 74 #define UART1_RX GPIOB(9) macro
125 #define UART1_RX GPIOB(11) macro
|
| A D | uart-sun50iw11.h | 64 #define UART1_RX GPIOL(9) macro
|
| A D | uart-sun8iw19.h | 69 #define UART1_RX GPIOG(7) macro
|
| A D | uart-sun8iw18.h | 69 #define UART1_RX GPIOG(7) macro
|
| /bsp/cvitek/drivers/ |
| A D | drv_pinmux.c | 159 …D_2, 0}, {IIC1_SCL, 1}, {AUX1, 2}, {XGPIOA_11, 3}, {UART1_RX, 4}, {PWM_11, 5}…
165 …RX, 0}, {CAM_MCLK0, 1}, {PWM_5, 2}, {XGPIOA_17, 3}, {UART1_RX, 4}, {AUX0, 5}, …
173 …{PWM_6, 2}, {XGPIOA_18, 3}, {UART1_CTS, 4}, {AUX1, 5}, {UART1_RX, 6}, FS_…
175 /* IIC0_SDA */ {{JTAG_TDO, 0}, {UART1_RX, 1}, {UART2_RX, 2}, {XGPIOA_29, 3},…
183 …TTON1, 0}, FS_NONE, FS_NONE, {PWR_GPIO_8, 3}, {UART1_RX, 4}, {IIC4_SDA, …
367 … {IIC1_SCL, 1}, {AUX1, 2}, {XGPIOA_11, 3}, {UART1_RX, 4}, {PWM_11,…
373 … {CAM_MCLK0, 1}, {PWM_5, 2}, {XGPIOA_17, 3}, {UART1_RX, 4}, {AUX0, 5…
382 … {XGPIOA_18, 3}, {UART1_CTS, 4}, {AUX1, 5}, {UART1_RX, 6}, {VO…
385 /* IIC0_SDA */ {{IIC0_SDA, 0}, {UART1_RX, 1}, {UART2_RX, 2}, {XGPIOA_2…
394 …, FS_NONE, FS_NONE, {PWR_GPIO_8, 3}, {UART1_RX, 4}, {IIC4_SD…
[all …]
|
| A D | drv_pinmux.h | 303 UART1_RX, enumerator
|
| A D | drv_uart.c | 457 pinmux_config(BSP_UART1_RX_PINNAME, UART1_RX, pinname_whitelist_uart1_rx); in rt_hw_uart_init()
|
| /bsp/allwinner/libraries/drivers/ |
| A D | drv_uart.c | 63 #define UART1_RX GPIOD(22) macro
66 #define UART1_RX GPIOE(11) macro
69 #define UART1_RX GPIOG(7) macro
72 #define UART1_RX GPIOG(13) macro
954 hal_gpio_set_pull(UART1_RX, GPIO_PULL_UP); in uart_pinctrl_init()
956 hal_gpio_pinmux_set_function(UART1_RX, UART1_RX_FUNCTION); // RX in uart_pinctrl_init()
|
| /bsp/rv32m1_vega/ |
| A D | README_zh.md | 70 | PTA25 | UART1_RX |
|
| A D | README.md | 74 | PTA25 | UART1_RX |
|
| /bsp/mm32f103x/ |
| A D | README.md | 66 使用MM32-LINK或Jlink等调试工具连接开发板到PC，通过调试调试工具供电或使用Micro-USB供电。若使用Jlink等调试工具，还需要将UART1_TX(PA9)、UART1_RX(PA…
|
| /bsp/mm32l3xx/ |
| A D | README.md | 66 使用MM32-LINK或Jlink等调试工具连接开发板到PC，通过调试调试工具供电或使用Micro-USB供电。若使用Jlink等调试工具，还需要将UART1_TX(PA9)、UART1_RX(PA…
|
| /bsp/mm32l07x/ |
| A D | README.md | 66 …接开发板到 PC ，通过调试调试工具供电或使用 Micro-USB 供电。若使用 Jlink 等调试工具，还需要将 UART1_TX(PA9)、UART1_RX(PA10)、GND 接到串口工具上。
|
| /bsp/k230/drivers/interdrv/pdma/ |
| A D | drv_pdma.h | 144 UART1_RX = 3, enumerator
|
| /bsp/allwinner/libraries/sunxi-hal/hal/source/uart/ |
| A D | hal_uart.c | 574 hal_gpio_set_pull(UART1_RX, GPIO_PULL_UP); in uart_pinctrl_init()
576 hal_gpio_pinmux_set_function(UART1_RX, UART1_GPIO_FUNCTION);//RX in uart_pinctrl_init()
605 hal_gpio_pinmux_set_function(UART1_RX, GPIO_MUXSEL_DISABLED);//RX in uart_pinctrl_uninit()
|
| /bsp/wch/risc-v/yd-ch32v307vct6/ |
| A D | README.md | 87 - board pin A10 (UART1_RX) -> converter TX (optional, for enter commands)
|
| /bsp/efm32/Libraries/Device/EnergyMicro/EFM32GG/Source/ARM/ |
| A D | startup_efm32gg.s | 105 DCD UART1_RX_IRQHandler ; 22: UART1_RX Interrupt
|
| /bsp/efm32/Libraries/Device/EnergyMicro/EFM32GG/Source/IAR/ |
| A D | startup_efm32gg.s | 105 DCD UART1_RX_IRQHandler ; 22: UART1_RX Interrupt
|
| /bsp/stm32/stm32l496-st-discovery/board/CubeMX_Config/ |
| A D | CubeMX_Config.ioc | 613 PG10.GPIO_Label=UART1_RX [STMOD+_UART]
|