| /bsp/gd32/risc-v/libraries/GD32VF103_Firmware_Library/GD32VF103_usbfs_library/driver/Include/ |
| A D | drv_usbh_int.h | 43 uint8_t (*connect) (usbh_host *puhost); member
|
| /bsp/rv32m1_vega/ |
| A D | README.md | 34 Please use JLink to connect to the JTAG interface of the RISC-V core on the RV32M1_VEGA board, and …
36 Use a USB cable to connect to a USB port marked with SDA, then a serial device is recognized by PC,…
38 …age file is generated after being correctly compiled, you can use gdb to connect to openocd and bu…
|
| /bsp/ESP32_C3/ |
| A D | esp32c3.gpb | 3 set remote interrupt-on-connect on
|
| /bsp/bouffalo_lab/libraries/bl_mcu_sdk/tools/bflb_tools/ |
| A D | get_bflb_fw_post_proc.sh | 41 curl -C - -LjO --connect-timeout 30 -m $timeout $url/$FILE_NAME
|
| A D | get_bouffalo_flash_cube.sh | 41 curl -C - -LjO --connect-timeout 30 -m $timeout $url/$FILE_NAME
|
| /bsp/Infineon/libraries/templates/XMC7200D/board/ |
| A D | Kconfig | 42 int "UART connect CPU Interrupt Number (0-7)"
|
| /bsp/Infineon/xmc7200-kit_xmc7200_evk/board/ |
| A D | Kconfig | 36 int "UART connect CPU Interrupt Number (0-7)"
|
| /bsp/efm32/ |
| A D | Readme.txt | 9 1. You should have a ENC28J60 Ethernet controller and connect it with your board properly
|
| /bsp/nrf5x/ |
| A D | README.md | 101 - 这个时候用nrf connect 来测试可以搜索到对应的beacon
125 - 之后用nrf connect 软件可以搜索到对应的beacon设备。
|
| /bsp/microchip/common/applications/ |
| A D | lwip_demo.c | 92 if (connect(sock, (struct sockaddr *)&server_addr, sizeof(struct sockaddr)) == -1) in tcpclient()
|
| /bsp/zynqmp-r5-axu4ev/ |
| A D | README.md | 54 4. Use the debugger to connect the PC and the development board. Set the dial switch to JTAG to sta…
82 …r burn to QSPI flash, set the startup mode through dial switch, and then connect the power supply …
|
| /bsp/wch/risc-v/ch32v208w-r0/ |
| A D | README_EN.md | 59 … instructions, and this summary will use the AT group to communicate with ESP8266 and connect WIFI.
83 Connect the `PA2` pin on the board to the `RX` pin of the module, connect the `PA3` pin to the `TX`…
139 …ard LED is not directly connected to the pin, the user needs to manually connect the LED to the co…
|
| /bsp/Infineon/xmc7100d-f144k4160aa/board/ |
| A D | Kconfig | 57 int "UART connect CPU Interrupt Number (0-7)"
|
| /bsp/Infineon/psoc6-evaluationkit-062S2/ |
| A D | README_EN.md | 46 Use the data cable to connect the development board to the PC.
64 …K` to download the program using the `SWD` method, use the data cable to connect to the developmen…
|
| /bsp/stm32/stm32f103-blue-pill/ |
| A D | README.md | 106 ### 3.1 Use ST-LINK Debugger to connect the Blue Pill Board
127 ### 3.2 Use FTDI adapter(USB to UART) to connect the Blue Pill Board's PA9(Tx) and PA10(Rx) pins
140 | VCC 3.3 | **Don't need to connect VCC 3.3 pin** |
141 | VCC 5 | **Don't need to connect VCC 5 pin** |
|
| /bsp/microchip/same70/bsp/documentation/ |
| A D | ethernet_phy.rst | 10 interface to connect a management entity and a managed PHY for the purposes of
|
| /bsp/microchip/same54/bsp/documentation/ |
| A D | ethernet_phy.rst | 10 interface to connect a management entity and a managed PHY for the purposes of
|
| /bsp/nuvoton/numaker-hmi-ma35d1/ |
| A D | README.md | 41 <li>Two 120-pin high speed connectors to connect with BASE board</li>
66 <li>Two 120-pin high speed connectors to connect with SOM board</li>
70 <li>One LCM connector to connect with 7-inch 1024x600 LCD daughter board</li>
|
| /bsp/simulator/drivers/winsock/ |
| A D | sal_winsock.c | 118 return (int)connect(s, windows_addr, namelen); in win_connect()
|
| /bsp/nuvoton/numaker-pfm-m487/ |
| A D | README.md | 51 …et the four switches to ‘ON’ position. After the configuration is done, connect the NuMaker-PFM-M…
|
| /bsp/nuvoton/numaker-m032ki/ |
| A D | README.md | 47 …Set the four switches to ‘ON’ position. After the configuration is done, connect the NuMaker-M032K…
|
| /bsp/nuvoton/numaker-m2354/ |
| A D | README.md | 47 …Set the four switches to ‘ON’ position. After the configuration is done, connect the NuMaker-M2354…
|
| /bsp/nuvoton/numaker-iot-m487/ |
| A D | README.md | 54 …et the four switches to ‘ON’ position. After the configuration is done, connect the NuMaker-IOT-M…
|
| /bsp/nxp/imx/imxrt/imxrt1021-nxp-evk/ |
| A D | README.md | 56 Use a USB cable to connect the development board to the PC and turn on the power switch.
|
| /bsp/nuvoton/numaker-iot-m467/ |
| A D | README.md | 69 …t the No.1/2 switches to ‘ON’ position. After the configuration is done, connect the NuMaker-IoT-M…
|