1 /** 2 ****************************************************************************** 3 * @file stm32f0xx_hal_conf.h 4 * @brief HAL configuration file. 5 ****************************************************************************** 6 * @attention 7 * 8 * <h2><center>© COPYRIGHT(c) 2019 STMicroelectronics</center></h2> 9 * 10 * Redistribution and use in source and binary forms, with or without modification, 11 * are permitted provided that the following conditions are met: 12 * 1. Redistributions of source code must retain the above copyright notice, 13 * this list of conditions and the following disclaimer. 14 * 2. Redistributions in binary form must reproduce the above copyright notice, 15 * this list of conditions and the following disclaimer in the documentation 16 * and/or other materials provided with the distribution. 17 * 3. Neither the name of STMicroelectronics nor the names of its contributors 18 * may be used to endorse or promote products derived from this software 19 * without specific prior written permission. 20 * 21 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 22 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 23 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 24 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE 25 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 26 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 27 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 28 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 29 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 31 * 32 ****************************************************************************** 33 */ 34 35 /* Define to prevent recursive inclusion -------------------------------------*/ 36 #ifndef __STM32F0xx_HAL_CONF_H 37 #define __STM32F0xx_HAL_CONF_H 38 39 #ifdef __cplusplus 40 extern "C" { 41 #endif 42 43 /* Exported types ------------------------------------------------------------*/ 44 /* Exported constants --------------------------------------------------------*/ 45 46 /* ########################## Module Selection ############################## */ 47 /** 48 * @brief This is the list of modules to be used in the HAL driver 49 */ 50 #define HAL_MODULE_ENABLED 51 #define HAL_ADC_MODULE_ENABLED 52 /*#define HAL_CRYP_MODULE_ENABLED */ 53 /*#define HAL_CAN_MODULE_ENABLED */ 54 /*#define HAL_CEC_MODULE_ENABLED */ 55 /*#define HAL_COMP_MODULE_ENABLED */ 56 /*#define HAL_CRC_MODULE_ENABLED */ 57 /*#define HAL_CRYP_MODULE_ENABLED */ 58 /*#define HAL_TSC_MODULE_ENABLED */ 59 /*#define HAL_DAC_MODULE_ENABLED */ 60 /*#define HAL_I2S_MODULE_ENABLED */ 61 #define HAL_IWDG_MODULE_ENABLED 62 /*#define HAL_LCD_MODULE_ENABLED */ 63 /*#define HAL_LPTIM_MODULE_ENABLED */ 64 /*#define HAL_RNG_MODULE_ENABLED */ 65 #define HAL_RTC_MODULE_ENABLED 66 #define HAL_SPI_MODULE_ENABLED 67 #define HAL_TIM_MODULE_ENABLED 68 #define HAL_UART_MODULE_ENABLED 69 #define HAL_USART_MODULE_ENABLED 70 /*#define HAL_IRDA_MODULE_ENABLED */ 71 /*#define HAL_SMARTCARD_MODULE_ENABLED */ 72 /*#define HAL_SMBUS_MODULE_ENABLED */ 73 /*#define HAL_WWDG_MODULE_ENABLED */ 74 /*#define HAL_PCD_MODULE_ENABLED */ 75 /*#define HAL_EXTI_MODULE_ENABLED */ 76 #define HAL_CORTEX_MODULE_ENABLED 77 #define HAL_DMA_MODULE_ENABLED 78 #define HAL_FLASH_MODULE_ENABLED 79 #define HAL_GPIO_MODULE_ENABLED 80 #define HAL_PWR_MODULE_ENABLED 81 #define HAL_RCC_MODULE_ENABLED 82 #define HAL_I2C_MODULE_ENABLED 83 84 /* ########################## HSE/HSI Values adaptation ##################### */ 85 /** 86 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 87 * This value is used by the RCC HAL module to compute the system frequency 88 * (when HSE is used as system clock source, directly or through the PLL). 89 */ 90 #if !defined (HSE_VALUE) 91 #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */ 92 #endif /* HSE_VALUE */ 93 94 /** 95 * @brief In the following line adjust the External High Speed oscillator (HSE) Startup 96 * Timeout value 97 */ 98 #if !defined (HSE_STARTUP_TIMEOUT) 99 #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */ 100 #endif /* HSE_STARTUP_TIMEOUT */ 101 102 /** 103 * @brief Internal High Speed oscillator (HSI) value. 104 * This value is used by the RCC HAL module to compute the system frequency 105 * (when HSI is used as system clock source, directly or through the PLL). 106 */ 107 #if !defined (HSI_VALUE) 108 #define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/ 109 #endif /* HSI_VALUE */ 110 111 /** 112 * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup 113 * Timeout value 114 */ 115 #if !defined (HSI_STARTUP_TIMEOUT) 116 #define HSI_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSI start up */ 117 #endif /* HSI_STARTUP_TIMEOUT */ 118 119 /** 120 * @brief Internal High Speed oscillator for ADC (HSI14) value. 121 */ 122 #if !defined (HSI14_VALUE) 123 #define HSI14_VALUE ((uint32_t)14000000) /*!< Value of the Internal High Speed oscillator for ADC in Hz. 124 The real value may vary depending on the variations 125 in voltage and temperature. */ 126 #endif /* HSI14_VALUE */ 127 128 /** 129 * @brief Internal High Speed oscillator for USB (HSI48) value. 130 */ 131 #if !defined (HSI48_VALUE) 132 #define HSI48_VALUE ((uint32_t)48000000) /*!< Value of the Internal High Speed oscillator for USB in Hz. 133 The real value may vary depending on the variations 134 in voltage and temperature. */ 135 #endif /* HSI48_VALUE */ 136 137 /** 138 * @brief Internal Low Speed oscillator (LSI) value. 139 */ 140 #if !defined (LSI_VALUE) 141 #define LSI_VALUE ((uint32_t)40000) 142 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 143 The real value may vary depending on the variations 144 in voltage and temperature. */ 145 /** 146 * @brief External Low Speed oscillator (LSI) value. 147 */ 148 #if !defined (LSE_VALUE) 149 #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ 150 #endif /* LSE_VALUE */ 151 152 #if !defined (LSE_STARTUP_TIMEOUT) 153 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ 154 #endif /* LSE_STARTUP_TIMEOUT */ 155 156 /* Tip: To avoid modifying this file each time you need to use different HSE, 157 === you can define the HSE value in your toolchain compiler preprocessor. */ 158 159 /* ########################### System Configuration ######################### */ 160 /** 161 * @brief This is the HAL system configuration section 162 */ 163 #define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ 164 #define TICK_INT_PRIORITY ((uint32_t)0) /*!< tick interrupt priority (lowest by default) */ 165 /* Warning: Must be set to higher priority for HAL_Delay() */ 166 /* and HAL_GetTick() usage under interrupt context */ 167 #define USE_RTOS 0 168 #define PREFETCH_ENABLE 1 169 #define INSTRUCTION_CACHE_ENABLE 0 170 #define DATA_CACHE_ENABLE 0 171 /* ########################## Assert Selection ############################## */ 172 /** 173 * @brief Uncomment the line below to expanse the "assert_param" macro in the 174 * HAL drivers code 175 */ 176 /* #define USE_FULL_ASSERT 1U */ 177 178 /* ################## SPI peripheral configuration ########################## */ 179 180 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 181 * Activated: CRC code is present inside driver 182 * Deactivated: CRC code cleaned from driver 183 */ 184 185 #define USE_SPI_CRC 0U 186 187 /* Includes ------------------------------------------------------------------*/ 188 /** 189 * @brief Include module's header file 190 */ 191 192 #ifdef HAL_RCC_MODULE_ENABLED 193 #include "stm32f0xx_hal_rcc.h" 194 #endif /* HAL_RCC_MODULE_ENABLED */ 195 196 #ifdef HAL_EXTI_MODULE_ENABLED 197 #include "stm32f0xx_hal_exti.h" 198 #endif /* HAL_EXTI_MODULE_ENABLED */ 199 200 #ifdef HAL_GPIO_MODULE_ENABLED 201 #include "stm32f0xx_hal_gpio.h" 202 #endif /* HAL_GPIO_MODULE_ENABLED */ 203 204 #ifdef HAL_DMA_MODULE_ENABLED 205 #include "stm32f0xx_hal_dma.h" 206 #endif /* HAL_DMA_MODULE_ENABLED */ 207 208 #ifdef HAL_CORTEX_MODULE_ENABLED 209 #include "stm32f0xx_hal_cortex.h" 210 #endif /* HAL_CORTEX_MODULE_ENABLED */ 211 212 #ifdef HAL_ADC_MODULE_ENABLED 213 #include "stm32f0xx_hal_adc.h" 214 #endif /* HAL_ADC_MODULE_ENABLED */ 215 216 #ifdef HAL_CAN_MODULE_ENABLED 217 #include "stm32f0xx_hal_can.h" 218 #endif /* HAL_CAN_MODULE_ENABLED */ 219 220 #ifdef HAL_CEC_MODULE_ENABLED 221 #include "stm32f0xx_hal_cec.h" 222 #endif /* HAL_CEC_MODULE_ENABLED */ 223 224 #ifdef HAL_COMP_MODULE_ENABLED 225 #include "stm32f0xx_hal_comp.h" 226 #endif /* HAL_COMP_MODULE_ENABLED */ 227 228 #ifdef HAL_CRC_MODULE_ENABLED 229 #include "stm32f0xx_hal_crc.h" 230 #endif /* HAL_CRC_MODULE_ENABLED */ 231 232 #ifdef HAL_DAC_MODULE_ENABLED 233 #include "stm32f0xx_hal_dac.h" 234 #endif /* HAL_DAC_MODULE_ENABLED */ 235 236 #ifdef HAL_FLASH_MODULE_ENABLED 237 #include "stm32f0xx_hal_flash.h" 238 #endif /* HAL_FLASH_MODULE_ENABLED */ 239 240 #ifdef HAL_I2C_MODULE_ENABLED 241 #include "stm32f0xx_hal_i2c.h" 242 #endif /* HAL_I2C_MODULE_ENABLED */ 243 244 #ifdef HAL_I2S_MODULE_ENABLED 245 #include "stm32f0xx_hal_i2s.h" 246 #endif /* HAL_I2S_MODULE_ENABLED */ 247 248 #ifdef HAL_IRDA_MODULE_ENABLED 249 #include "stm32f0xx_hal_irda.h" 250 #endif /* HAL_IRDA_MODULE_ENABLED */ 251 252 #ifdef HAL_IWDG_MODULE_ENABLED 253 #include "stm32f0xx_hal_iwdg.h" 254 #endif /* HAL_IWDG_MODULE_ENABLED */ 255 256 #ifdef HAL_PCD_MODULE_ENABLED 257 #include "stm32f0xx_hal_pcd.h" 258 #endif /* HAL_PCD_MODULE_ENABLED */ 259 260 #ifdef HAL_PWR_MODULE_ENABLED 261 #include "stm32f0xx_hal_pwr.h" 262 #endif /* HAL_PWR_MODULE_ENABLED */ 263 264 #ifdef HAL_RTC_MODULE_ENABLED 265 #include "stm32f0xx_hal_rtc.h" 266 #endif /* HAL_RTC_MODULE_ENABLED */ 267 268 #ifdef HAL_SMARTCARD_MODULE_ENABLED 269 #include "stm32f0xx_hal_smartcard.h" 270 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 271 272 #ifdef HAL_SMBUS_MODULE_ENABLED 273 #include "stm32f0xx_hal_smbus.h" 274 #endif /* HAL_SMBUS_MODULE_ENABLED */ 275 276 #ifdef HAL_SPI_MODULE_ENABLED 277 #include "stm32f0xx_hal_spi.h" 278 #endif /* HAL_SPI_MODULE_ENABLED */ 279 280 #ifdef HAL_TIM_MODULE_ENABLED 281 #include "stm32f0xx_hal_tim.h" 282 #endif /* HAL_TIM_MODULE_ENABLED */ 283 284 #ifdef HAL_TSC_MODULE_ENABLED 285 #include "stm32f0xx_hal_tsc.h" 286 #endif /* HAL_TSC_MODULE_ENABLED */ 287 288 #ifdef HAL_UART_MODULE_ENABLED 289 #include "stm32f0xx_hal_uart.h" 290 #endif /* HAL_UART_MODULE_ENABLED */ 291 292 #ifdef HAL_USART_MODULE_ENABLED 293 #include "stm32f0xx_hal_usart.h" 294 #endif /* HAL_USART_MODULE_ENABLED */ 295 296 #ifdef HAL_WWDG_MODULE_ENABLED 297 #include "stm32f0xx_hal_wwdg.h" 298 #endif /* HAL_WWDG_MODULE_ENABLED */ 299 300 /* Exported macro ------------------------------------------------------------*/ 301 #ifdef USE_FULL_ASSERT 302 /** 303 * @brief The assert_param macro is used for function's parameters check. 304 * @param expr: If expr is false, it calls assert_failed function 305 * which reports the name of the source file and the source 306 * line number of the call that failed. 307 * If expr is true, it returns no value. 308 * @retval None 309 */ 310 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((char *)__FILE__, __LINE__)) 311 /* Exported functions ------------------------------------------------------- */ 312 void assert_failed(char* file, uint32_t line); 313 #else 314 #define assert_param(expr) ((void)0U) 315 #endif /* USE_FULL_ASSERT */ 316 317 #ifdef __cplusplus 318 } 319 #endif 320 321 #endif /* __STM32F0xx_HAL_CONF_H */ 322 323 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 324