1 /** 2 ****************************************************************************** 3 * @file stm32f4xx_hal_conf.h 4 * @brief HAL configuration file. 5 ****************************************************************************** 6 * @attention 7 * 8 * <h2><center>© COPYRIGHT(c) 2020 STMicroelectronics</center></h2> 9 * 10 * Redistribution and use in source and binary forms, with or without modification, 11 * are permitted provided that the following conditions are met: 12 * 1. Redistributions of source code must retain the above copyright notice, 13 * this list of conditions and the following disclaimer. 14 * 2. Redistributions in binary form must reproduce the above copyright notice, 15 * this list of conditions and the following disclaimer in the documentation 16 * and/or other materials provided with the distribution. 17 * 3. Neither the name of STMicroelectronics nor the names of its contributors 18 * may be used to endorse or promote products derived from this software 19 * without specific prior written permission. 20 * 21 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 22 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 23 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 24 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE 25 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 26 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 27 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 28 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 29 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 31 * 32 ****************************************************************************** 33 */ 34 35 /* Define to prevent recursive inclusion -------------------------------------*/ 36 #ifndef __STM32F4xx_HAL_CONF_H 37 #define __STM32F4xx_HAL_CONF_H 38 39 #ifdef __cplusplus 40 extern "C" { 41 #endif 42 43 /* Exported types ------------------------------------------------------------*/ 44 /* Exported constants --------------------------------------------------------*/ 45 46 /* ########################## Module Selection ############################## */ 47 /** 48 * @brief This is the list of modules to be used in the HAL driver 49 */ 50 #define HAL_MODULE_ENABLED 51 52 #define HAL_ADC_MODULE_ENABLED 53 /* #define HAL_CRYP_MODULE_ENABLED */ 54 /* #define HAL_CAN_MODULE_ENABLED */ 55 /* #define HAL_CRC_MODULE_ENABLED */ 56 /* #define HAL_CRYP_MODULE_ENABLED */ 57 /* #define HAL_DAC_MODULE_ENABLED */ 58 /* #define HAL_DCMI_MODULE_ENABLED */ 59 /* #define HAL_DMA2D_MODULE_ENABLED */ 60 /* #define HAL_ETH_MODULE_ENABLED */ 61 /* #define HAL_NAND_MODULE_ENABLED */ 62 /* #define HAL_NOR_MODULE_ENABLED */ 63 /* #define HAL_PCCARD_MODULE_ENABLED */ 64 /* #define HAL_SRAM_MODULE_ENABLED */ 65 /* #define HAL_SDRAM_MODULE_ENABLED */ 66 /* #define HAL_HASH_MODULE_ENABLED */ 67 #define HAL_I2C_MODULE_ENABLED 68 /* #define HAL_I2S_MODULE_ENABLED */ 69 #define HAL_IWDG_MODULE_ENABLED 70 /* #define HAL_LTDC_MODULE_ENABLED */ 71 /* #define HAL_RNG_MODULE_ENABLED */ 72 #define HAL_RTC_MODULE_ENABLED 73 /* #define HAL_SAI_MODULE_ENABLED */ 74 /* #define HAL_SD_MODULE_ENABLED */ 75 /* #define HAL_MMC_MODULE_ENABLED */ 76 #define HAL_SPI_MODULE_ENABLED 77 /* #define HAL_TIM_MODULE_ENABLED */ 78 #define HAL_UART_MODULE_ENABLED 79 /* #define HAL_USART_MODULE_ENABLED */ 80 /* #define HAL_IRDA_MODULE_ENABLED */ 81 /* #define HAL_SMARTCARD_MODULE_ENABLED */ 82 /* #define HAL_WWDG_MODULE_ENABLED */ 83 /* #define HAL_PCD_MODULE_ENABLED */ 84 /* #define HAL_HCD_MODULE_ENABLED */ 85 /* #define HAL_DSI_MODULE_ENABLED */ 86 /* #define HAL_QSPI_MODULE_ENABLED */ 87 /* #define HAL_QSPI_MODULE_ENABLED */ 88 /* #define HAL_CEC_MODULE_ENABLED */ 89 /* #define HAL_FMPI2C_MODULE_ENABLED */ 90 /* #define HAL_SPDIFRX_MODULE_ENABLED */ 91 /* #define HAL_DFSDM_MODULE_ENABLED */ 92 /* #define HAL_LPTIM_MODULE_ENABLED */ 93 /* #define HAL_EXTI_MODULE_ENABLED */ 94 #define HAL_GPIO_MODULE_ENABLED 95 #define HAL_DMA_MODULE_ENABLED 96 #define HAL_RCC_MODULE_ENABLED 97 #define HAL_FLASH_MODULE_ENABLED 98 #define HAL_PWR_MODULE_ENABLED 99 #define HAL_CORTEX_MODULE_ENABLED 100 101 /* ########################## HSE/HSI Values adaptation ##################### */ 102 /** 103 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 104 * This value is used by the RCC HAL module to compute the system frequency 105 * (when HSE is used as system clock source, directly or through the PLL). 106 */ 107 #if !defined (HSE_VALUE) 108 #define HSE_VALUE ((uint32_t)25000000U) /*!< Value of the External oscillator in Hz */ 109 #endif /* HSE_VALUE */ 110 111 #if !defined (HSE_STARTUP_TIMEOUT) 112 #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ 113 #endif /* HSE_STARTUP_TIMEOUT */ 114 115 /** 116 * @brief Internal High Speed oscillator (HSI) value. 117 * This value is used by the RCC HAL module to compute the system frequency 118 * (when HSI is used as system clock source, directly or through the PLL). 119 */ 120 #if !defined (HSI_VALUE) 121 #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ 122 #endif /* HSI_VALUE */ 123 124 /** 125 * @brief Internal Low Speed oscillator (LSI) value. 126 */ 127 #if !defined (LSI_VALUE) 128 #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ 129 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 130 The real value may vary depending on the variations 131 in voltage and temperature.*/ 132 /** 133 * @brief External Low Speed oscillator (LSE) value. 134 */ 135 #if !defined (LSE_VALUE) 136 #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ 137 #endif /* LSE_VALUE */ 138 139 #if !defined (LSE_STARTUP_TIMEOUT) 140 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ 141 #endif /* LSE_STARTUP_TIMEOUT */ 142 143 /** 144 * @brief External clock source for I2S peripheral 145 * This value is used by the I2S HAL module to compute the I2S clock source 146 * frequency, this source is inserted directly through I2S_CKIN pad. 147 */ 148 #if !defined (EXTERNAL_CLOCK_VALUE) 149 #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the External audio frequency in Hz*/ 150 #endif /* EXTERNAL_CLOCK_VALUE */ 151 152 /* Tip: To avoid modifying this file each time you need to use different HSE, 153 === you can define the HSE value in your toolchain compiler preprocessor. */ 154 155 /* ########################### System Configuration ######################### */ 156 /** 157 * @brief This is the HAL system configuration section 158 */ 159 #define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ 160 #define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */ 161 #define USE_RTOS 0U 162 #define PREFETCH_ENABLE 1U 163 #define INSTRUCTION_CACHE_ENABLE 1U 164 #define DATA_CACHE_ENABLE 1U 165 166 /* ########################## Assert Selection ############################## */ 167 /** 168 * @brief Uncomment the line below to expanse the "assert_param" macro in the 169 * HAL drivers code 170 */ 171 /* #define USE_FULL_ASSERT 1U */ 172 173 /* ################## Ethernet peripheral configuration ##################### */ 174 175 /* Section 1 : Ethernet peripheral configuration */ 176 177 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 178 #define MAC_ADDR0 2U 179 #define MAC_ADDR1 0U 180 #define MAC_ADDR2 0U 181 #define MAC_ADDR3 0U 182 #define MAC_ADDR4 0U 183 #define MAC_ADDR5 0U 184 185 /* Definition of the Ethernet driver buffers size and count */ 186 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 187 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 188 #define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 189 #define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 190 191 /* Section 2: PHY configuration section */ 192 193 /* DP83848_PHY_ADDRESS Address*/ 194 #define DP83848_PHY_ADDRESS 0x01U 195 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 196 #define PHY_RESET_DELAY ((uint32_t)0x000000FFU) 197 /* PHY Configuration delay */ 198 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU) 199 200 #define PHY_READ_TO ((uint32_t)0x0000FFFFU) 201 #define PHY_WRITE_TO ((uint32_t)0x0000FFFFU) 202 203 /* Section 3: Common PHY Registers */ 204 205 #define PHY_BCR ((uint16_t)0x0000U) /*!< Transceiver Basic Control Register */ 206 #define PHY_BSR ((uint16_t)0x0001U) /*!< Transceiver Basic Status Register */ 207 208 #define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */ 209 #define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */ 210 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */ 211 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */ 212 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */ 213 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */ 214 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */ 215 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */ 216 #define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */ 217 #define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */ 218 219 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */ 220 #define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */ 221 #define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */ 222 223 /* Section 4: Extended PHY Registers */ 224 #define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */ 225 226 #define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */ 227 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */ 228 229 /* ################## SPI peripheral configuration ########################## */ 230 231 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 232 * Activated: CRC code is present inside driver 233 * Deactivated: CRC code cleaned from driver 234 */ 235 236 #define USE_SPI_CRC 0U 237 238 /* Includes ------------------------------------------------------------------*/ 239 /** 240 * @brief Include module's header file 241 */ 242 243 #ifdef HAL_RCC_MODULE_ENABLED 244 #include "stm32f4xx_hal_rcc.h" 245 #endif /* HAL_RCC_MODULE_ENABLED */ 246 247 #ifdef HAL_EXTI_MODULE_ENABLED 248 #include "stm32f4xx_hal_exti.h" 249 #endif /* HAL_EXTI_MODULE_ENABLED */ 250 251 #ifdef HAL_GPIO_MODULE_ENABLED 252 #include "stm32f4xx_hal_gpio.h" 253 #endif /* HAL_GPIO_MODULE_ENABLED */ 254 255 #ifdef HAL_DMA_MODULE_ENABLED 256 #include "stm32f4xx_hal_dma.h" 257 #endif /* HAL_DMA_MODULE_ENABLED */ 258 259 #ifdef HAL_CORTEX_MODULE_ENABLED 260 #include "stm32f4xx_hal_cortex.h" 261 #endif /* HAL_CORTEX_MODULE_ENABLED */ 262 263 #ifdef HAL_ADC_MODULE_ENABLED 264 #include "stm32f4xx_hal_adc.h" 265 #endif /* HAL_ADC_MODULE_ENABLED */ 266 267 #ifdef HAL_CAN_MODULE_ENABLED 268 #include "stm32f4xx_hal_can.h" 269 #endif /* HAL_CAN_MODULE_ENABLED */ 270 271 #ifdef HAL_CRC_MODULE_ENABLED 272 #include "stm32f4xx_hal_crc.h" 273 #endif /* HAL_CRC_MODULE_ENABLED */ 274 275 #ifdef HAL_CRYP_MODULE_ENABLED 276 #include "stm32f4xx_hal_cryp.h" 277 #endif /* HAL_CRYP_MODULE_ENABLED */ 278 279 #ifdef HAL_DMA2D_MODULE_ENABLED 280 #include "stm32f4xx_hal_dma2d.h" 281 #endif /* HAL_DMA2D_MODULE_ENABLED */ 282 283 #ifdef HAL_DAC_MODULE_ENABLED 284 #include "stm32f4xx_hal_dac.h" 285 #endif /* HAL_DAC_MODULE_ENABLED */ 286 287 #ifdef HAL_DCMI_MODULE_ENABLED 288 #include "stm32f4xx_hal_dcmi.h" 289 #endif /* HAL_DCMI_MODULE_ENABLED */ 290 291 #ifdef HAL_ETH_MODULE_ENABLED 292 #include "stm32f4xx_hal_eth.h" 293 #endif /* HAL_ETH_MODULE_ENABLED */ 294 295 #ifdef HAL_FLASH_MODULE_ENABLED 296 #include "stm32f4xx_hal_flash.h" 297 #endif /* HAL_FLASH_MODULE_ENABLED */ 298 299 #ifdef HAL_SRAM_MODULE_ENABLED 300 #include "stm32f4xx_hal_sram.h" 301 #endif /* HAL_SRAM_MODULE_ENABLED */ 302 303 #ifdef HAL_NOR_MODULE_ENABLED 304 #include "stm32f4xx_hal_nor.h" 305 #endif /* HAL_NOR_MODULE_ENABLED */ 306 307 #ifdef HAL_NAND_MODULE_ENABLED 308 #include "stm32f4xx_hal_nand.h" 309 #endif /* HAL_NAND_MODULE_ENABLED */ 310 311 #ifdef HAL_PCCARD_MODULE_ENABLED 312 #include "stm32f4xx_hal_pccard.h" 313 #endif /* HAL_PCCARD_MODULE_ENABLED */ 314 315 #ifdef HAL_SDRAM_MODULE_ENABLED 316 #include "stm32f4xx_hal_sdram.h" 317 #endif /* HAL_SDRAM_MODULE_ENABLED */ 318 319 #ifdef HAL_HASH_MODULE_ENABLED 320 #include "stm32f4xx_hal_hash.h" 321 #endif /* HAL_HASH_MODULE_ENABLED */ 322 323 #ifdef HAL_I2C_MODULE_ENABLED 324 #include "stm32f4xx_hal_i2c.h" 325 #endif /* HAL_I2C_MODULE_ENABLED */ 326 327 #ifdef HAL_I2S_MODULE_ENABLED 328 #include "stm32f4xx_hal_i2s.h" 329 #endif /* HAL_I2S_MODULE_ENABLED */ 330 331 #ifdef HAL_IWDG_MODULE_ENABLED 332 #include "stm32f4xx_hal_iwdg.h" 333 #endif /* HAL_IWDG_MODULE_ENABLED */ 334 335 #ifdef HAL_LTDC_MODULE_ENABLED 336 #include "stm32f4xx_hal_ltdc.h" 337 #endif /* HAL_LTDC_MODULE_ENABLED */ 338 339 #ifdef HAL_PWR_MODULE_ENABLED 340 #include "stm32f4xx_hal_pwr.h" 341 #endif /* HAL_PWR_MODULE_ENABLED */ 342 343 #ifdef HAL_RNG_MODULE_ENABLED 344 #include "stm32f4xx_hal_rng.h" 345 #endif /* HAL_RNG_MODULE_ENABLED */ 346 347 #ifdef HAL_RTC_MODULE_ENABLED 348 #include "stm32f4xx_hal_rtc.h" 349 #endif /* HAL_RTC_MODULE_ENABLED */ 350 351 #ifdef HAL_SAI_MODULE_ENABLED 352 #include "stm32f4xx_hal_sai.h" 353 #endif /* HAL_SAI_MODULE_ENABLED */ 354 355 #ifdef HAL_SD_MODULE_ENABLED 356 #include "stm32f4xx_hal_sd.h" 357 #endif /* HAL_SD_MODULE_ENABLED */ 358 359 #ifdef HAL_MMC_MODULE_ENABLED 360 #include "stm32f4xx_hal_mmc.h" 361 #endif /* HAL_MMC_MODULE_ENABLED */ 362 363 #ifdef HAL_SPI_MODULE_ENABLED 364 #include "stm32f4xx_hal_spi.h" 365 #endif /* HAL_SPI_MODULE_ENABLED */ 366 367 #ifdef HAL_TIM_MODULE_ENABLED 368 #include "stm32f4xx_hal_tim.h" 369 #endif /* HAL_TIM_MODULE_ENABLED */ 370 371 #ifdef HAL_UART_MODULE_ENABLED 372 #include "stm32f4xx_hal_uart.h" 373 #endif /* HAL_UART_MODULE_ENABLED */ 374 375 #ifdef HAL_USART_MODULE_ENABLED 376 #include "stm32f4xx_hal_usart.h" 377 #endif /* HAL_USART_MODULE_ENABLED */ 378 379 #ifdef HAL_IRDA_MODULE_ENABLED 380 #include "stm32f4xx_hal_irda.h" 381 #endif /* HAL_IRDA_MODULE_ENABLED */ 382 383 #ifdef HAL_SMARTCARD_MODULE_ENABLED 384 #include "stm32f4xx_hal_smartcard.h" 385 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 386 387 #ifdef HAL_WWDG_MODULE_ENABLED 388 #include "stm32f4xx_hal_wwdg.h" 389 #endif /* HAL_WWDG_MODULE_ENABLED */ 390 391 #ifdef HAL_PCD_MODULE_ENABLED 392 #include "stm32f4xx_hal_pcd.h" 393 #endif /* HAL_PCD_MODULE_ENABLED */ 394 395 #ifdef HAL_HCD_MODULE_ENABLED 396 #include "stm32f4xx_hal_hcd.h" 397 #endif /* HAL_HCD_MODULE_ENABLED */ 398 399 #ifdef HAL_DSI_MODULE_ENABLED 400 #include "stm32f4xx_hal_dsi.h" 401 #endif /* HAL_DSI_MODULE_ENABLED */ 402 403 #ifdef HAL_QSPI_MODULE_ENABLED 404 #include "stm32f4xx_hal_qspi.h" 405 #endif /* HAL_QSPI_MODULE_ENABLED */ 406 407 #ifdef HAL_CEC_MODULE_ENABLED 408 #include "stm32f4xx_hal_cec.h" 409 #endif /* HAL_CEC_MODULE_ENABLED */ 410 411 #ifdef HAL_FMPI2C_MODULE_ENABLED 412 #include "stm32f4xx_hal_fmpi2c.h" 413 #endif /* HAL_FMPI2C_MODULE_ENABLED */ 414 415 #ifdef HAL_SPDIFRX_MODULE_ENABLED 416 #include "stm32f4xx_hal_spdifrx.h" 417 #endif /* HAL_SPDIFRX_MODULE_ENABLED */ 418 419 #ifdef HAL_DFSDM_MODULE_ENABLED 420 #include "stm32f4xx_hal_dfsdm.h" 421 #endif /* HAL_DFSDM_MODULE_ENABLED */ 422 423 #ifdef HAL_LPTIM_MODULE_ENABLED 424 #include "stm32f4xx_hal_lptim.h" 425 #endif /* HAL_LPTIM_MODULE_ENABLED */ 426 427 /* Exported macro ------------------------------------------------------------*/ 428 #ifdef USE_FULL_ASSERT 429 /** 430 * @brief The assert_param macro is used for function's parameters check. 431 * @param expr: If expr is false, it calls assert_failed function 432 * which reports the name of the source file and the source 433 * line number of the call that failed. 434 * If expr is true, it returns no value. 435 * @retval None 436 */ 437 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 438 /* Exported functions ------------------------------------------------------- */ 439 void assert_failed(uint8_t* file, uint32_t line); 440 #else 441 #define assert_param(expr) ((void)0U) 442 #endif /* USE_FULL_ASSERT */ 443 444 #ifdef __cplusplus 445 } 446 #endif 447 448 #endif /* __STM32F4xx_HAL_CONF_H */ 449 450 451 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 452