1 /** 2 ****************************************************************************** 3 * @file stm32f4xx_hal_conf_template.h 4 * @author MCD Application Team 5 * @brief HAL configuration template file. 6 * This file should be copied to the application folder and renamed 7 * to stm32f4xx_hal_conf.h. 8 ****************************************************************************** 9 * @attention 10 * 11 * <h2><center>© Copyright (c) 2017 STMicroelectronics. 12 * All rights reserved.</center></h2> 13 * 14 * This software component is licensed by ST under BSD 3-Clause license, 15 * the "License"; You may not use this file except in compliance with the 16 * License. You may obtain a copy of the License at: 17 * opensource.org/licenses/BSD-3-Clause 18 * 19 ****************************************************************************** 20 */ 21 22 /* Define to prevent recursive inclusion -------------------------------------*/ 23 #ifndef __STM32F4xx_HAL_CONF_H 24 #define __STM32F4xx_HAL_CONF_H 25 26 #ifdef __cplusplus 27 extern "C" { 28 #endif 29 30 /* Exported types ------------------------------------------------------------*/ 31 /* Exported constants --------------------------------------------------------*/ 32 33 /* ########################## Module Selection ############################## */ 34 /** 35 * @brief This is the list of modules to be used in the HAL driver 36 */ 37 #define HAL_MODULE_ENABLED 38 39 #define HAL_ADC_MODULE_ENABLED 40 /* #define HAL_CRYP_MODULE_ENABLED */ 41 /* #define HAL_CAN_MODULE_ENABLED */ 42 /* #define HAL_CRC_MODULE_ENABLED */ 43 /* #define HAL_CRYP_MODULE_ENABLED */ 44 /* #define HAL_DAC_MODULE_ENABLED */ 45 /* #define HAL_DCMI_MODULE_ENABLED */ 46 /* #define HAL_DMA2D_MODULE_ENABLED */ 47 #define HAL_ETH_MODULE_ENABLED 48 /* #define HAL_NAND_MODULE_ENABLED */ 49 /* #define HAL_NOR_MODULE_ENABLED */ 50 /* #define HAL_PCCARD_MODULE_ENABLED */ 51 /* #define HAL_SRAM_MODULE_ENABLED */ 52 #define HAL_SDRAM_MODULE_ENABLED 53 /* #define HAL_HASH_MODULE_ENABLED */ 54 /* #define HAL_I2C_MODULE_ENABLED */ 55 /* #define HAL_I2S_MODULE_ENABLED */ 56 #define HAL_IWDG_MODULE_ENABLED 57 /* #define HAL_LTDC_MODULE_ENABLED */ 58 /* #define HAL_RNG_MODULE_ENABLED */ 59 #define HAL_RTC_MODULE_ENABLED 60 #define HAL_SAI_MODULE_ENABLED 61 #define HAL_SD_MODULE_ENABLED 62 /* #define HAL_MMC_MODULE_ENABLED */ 63 #define HAL_SPI_MODULE_ENABLED 64 #define HAL_TIM_MODULE_ENABLED 65 #define HAL_UART_MODULE_ENABLED 66 /* #define HAL_USART_MODULE_ENABLED */ 67 /* #define HAL_IRDA_MODULE_ENABLED */ 68 /* #define HAL_SMARTCARD_MODULE_ENABLED */ 69 /* #define HAL_WWDG_MODULE_ENABLED */ 70 /* #define HAL_PCD_MODULE_ENABLED */ 71 #define HAL_HCD_MODULE_ENABLED 72 /* #define HAL_DSI_MODULE_ENABLED */ 73 /* #define HAL_QSPI_MODULE_ENABLED */ 74 /* #define HAL_QSPI_MODULE_ENABLED */ 75 /* #define HAL_CEC_MODULE_ENABLED */ 76 /* #define HAL_FMPI2C_MODULE_ENABLED */ 77 /* #define HAL_SPDIFRX_MODULE_ENABLED */ 78 /* #define HAL_DFSDM_MODULE_ENABLED */ 79 /* #define HAL_LPTIM_MODULE_ENABLED */ 80 /* #define HAL_EXTI_MODULE_ENABLED */ 81 #define HAL_GPIO_MODULE_ENABLED 82 #define HAL_EXTI_MODULE_ENABLED 83 #define HAL_DMA_MODULE_ENABLED 84 #define HAL_RCC_MODULE_ENABLED 85 #define HAL_FLASH_MODULE_ENABLED 86 #define HAL_PWR_MODULE_ENABLED 87 #define HAL_CORTEX_MODULE_ENABLED 88 89 /* ########################## HSE/HSI Values adaptation ##################### */ 90 /** 91 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 92 * This value is used by the RCC HAL module to compute the system frequency 93 * (when HSE is used as system clock source, directly or through the PLL). 94 */ 95 #if !defined (HSE_VALUE) 96 #define HSE_VALUE ((uint32_t)25000000U) /*!< Value of the External oscillator in Hz */ 97 #endif /* HSE_VALUE */ 98 99 #if !defined (HSE_STARTUP_TIMEOUT) 100 #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ 101 #endif /* HSE_STARTUP_TIMEOUT */ 102 103 /** 104 * @brief Internal High Speed oscillator (HSI) value. 105 * This value is used by the RCC HAL module to compute the system frequency 106 * (when HSI is used as system clock source, directly or through the PLL). 107 */ 108 #if !defined (HSI_VALUE) 109 #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ 110 #endif /* HSI_VALUE */ 111 112 /** 113 * @brief Internal Low Speed oscillator (LSI) value. 114 */ 115 #if !defined (LSI_VALUE) 116 #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ 117 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 118 The real value may vary depending on the variations 119 in voltage and temperature.*/ 120 /** 121 * @brief External Low Speed oscillator (LSE) value. 122 */ 123 #if !defined (LSE_VALUE) 124 #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ 125 #endif /* LSE_VALUE */ 126 127 #if !defined (LSE_STARTUP_TIMEOUT) 128 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ 129 #endif /* LSE_STARTUP_TIMEOUT */ 130 131 /** 132 * @brief External clock source for I2S peripheral 133 * This value is used by the I2S HAL module to compute the I2S clock source 134 * frequency, this source is inserted directly through I2S_CKIN pad. 135 */ 136 #if !defined (EXTERNAL_CLOCK_VALUE) 137 #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the External audio frequency in Hz*/ 138 #endif /* EXTERNAL_CLOCK_VALUE */ 139 140 /* Tip: To avoid modifying this file each time you need to use different HSE, 141 === you can define the HSE value in your toolchain compiler preprocessor. */ 142 143 /* ########################### System Configuration ######################### */ 144 /** 145 * @brief This is the HAL system configuration section 146 */ 147 #define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ 148 #define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */ 149 #define USE_RTOS 0U 150 #define PREFETCH_ENABLE 1U 151 #define INSTRUCTION_CACHE_ENABLE 1U 152 #define DATA_CACHE_ENABLE 1U 153 154 /* ########################## Assert Selection ############################## */ 155 /** 156 * @brief Uncomment the line below to expanse the "assert_param" macro in the 157 * HAL drivers code 158 */ 159 /* #define USE_FULL_ASSERT 1U */ 160 161 /* ################## Ethernet peripheral configuration ##################### */ 162 163 /* Section 1 : Ethernet peripheral configuration */ 164 165 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 166 #define MAC_ADDR0 2U 167 #define MAC_ADDR1 0U 168 #define MAC_ADDR2 0U 169 #define MAC_ADDR3 0U 170 #define MAC_ADDR4 0U 171 #define MAC_ADDR5 0U 172 173 /* Definition of the Ethernet driver buffers size and count */ 174 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 175 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 176 #define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 177 #define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 178 179 /* Section 2: PHY configuration section */ 180 181 /* LAN8742A_PHY_ADDRESS Address*/ 182 #define LAN8742A_PHY_ADDRESS 1U 183 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 184 #define PHY_RESET_DELAY ((uint32_t)0x000000FFU) 185 /* PHY Configuration delay */ 186 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU) 187 188 #define PHY_READ_TO ((uint32_t)0x0000FFFFU) 189 #define PHY_WRITE_TO ((uint32_t)0x0000FFFFU) 190 191 /* Section 3: Common PHY Registers */ 192 193 #define PHY_BCR ((uint16_t)0x00U) /*!< Transceiver Basic Control Register */ 194 #define PHY_BSR ((uint16_t)0x01U) /*!< Transceiver Basic Status Register */ 195 196 #define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */ 197 #define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */ 198 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */ 199 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */ 200 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */ 201 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */ 202 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */ 203 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */ 204 #define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */ 205 #define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */ 206 207 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */ 208 #define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */ 209 #define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */ 210 211 /* Section 4: Extended PHY Registers */ 212 #define PHY_SR ((uint16_t)0x1FU) /*!< PHY status register Offset */ 213 214 #define PHY_SPEED_STATUS ((uint16_t)0x0004U) /*!< PHY Speed mask */ 215 #define PHY_DUPLEX_STATUS ((uint16_t)0x0010U) /*!< PHY Duplex mask */ 216 217 #define PHY_ISFR ((uint16_t)0x001DU) /*!< PHY Interrupt Source Flag register Offset */ 218 #define PHY_ISFR_INT4 ((uint16_t)0x000BU) /*!< PHY Link down inturrupt */ 219 220 /* ################## SPI peripheral configuration ########################## */ 221 222 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 223 * Activated: CRC code is present inside driver 224 * Deactivated: CRC code cleaned from driver 225 */ 226 227 #define USE_SPI_CRC 0U 228 229 /* Includes ------------------------------------------------------------------*/ 230 /** 231 * @brief Include module's header file 232 */ 233 234 #ifdef HAL_RCC_MODULE_ENABLED 235 #include "stm32f4xx_hal_rcc.h" 236 #endif /* HAL_RCC_MODULE_ENABLED */ 237 238 #ifdef HAL_EXTI_MODULE_ENABLED 239 #include "stm32f4xx_hal_exti.h" 240 #endif /* HAL_EXTI_MODULE_ENABLED */ 241 242 #ifdef HAL_GPIO_MODULE_ENABLED 243 #include "stm32f4xx_hal_gpio.h" 244 #endif /* HAL_GPIO_MODULE_ENABLED */ 245 246 #ifdef HAL_DMA_MODULE_ENABLED 247 #include "stm32f4xx_hal_dma.h" 248 #endif /* HAL_DMA_MODULE_ENABLED */ 249 250 #ifdef HAL_CORTEX_MODULE_ENABLED 251 #include "stm32f4xx_hal_cortex.h" 252 #endif /* HAL_CORTEX_MODULE_ENABLED */ 253 254 #ifdef HAL_ADC_MODULE_ENABLED 255 #include "stm32f4xx_hal_adc.h" 256 #endif /* HAL_ADC_MODULE_ENABLED */ 257 258 #ifdef HAL_CAN_MODULE_ENABLED 259 #include "stm32f4xx_hal_can.h" 260 #endif /* HAL_CAN_MODULE_ENABLED */ 261 262 #ifdef HAL_CRC_MODULE_ENABLED 263 #include "stm32f4xx_hal_crc.h" 264 #endif /* HAL_CRC_MODULE_ENABLED */ 265 266 #ifdef HAL_CRYP_MODULE_ENABLED 267 #include "stm32f4xx_hal_cryp.h" 268 #endif /* HAL_CRYP_MODULE_ENABLED */ 269 270 #ifdef HAL_DMA2D_MODULE_ENABLED 271 #include "stm32f4xx_hal_dma2d.h" 272 #endif /* HAL_DMA2D_MODULE_ENABLED */ 273 274 #ifdef HAL_DAC_MODULE_ENABLED 275 #include "stm32f4xx_hal_dac.h" 276 #endif /* HAL_DAC_MODULE_ENABLED */ 277 278 #ifdef HAL_DCMI_MODULE_ENABLED 279 #include "stm32f4xx_hal_dcmi.h" 280 #endif /* HAL_DCMI_MODULE_ENABLED */ 281 282 #ifdef HAL_ETH_MODULE_ENABLED 283 #include "stm32f4xx_hal_eth.h" 284 #endif /* HAL_ETH_MODULE_ENABLED */ 285 286 #ifdef HAL_FLASH_MODULE_ENABLED 287 #include "stm32f4xx_hal_flash.h" 288 #endif /* HAL_FLASH_MODULE_ENABLED */ 289 290 #ifdef HAL_SRAM_MODULE_ENABLED 291 #include "stm32f4xx_hal_sram.h" 292 #endif /* HAL_SRAM_MODULE_ENABLED */ 293 294 #ifdef HAL_NOR_MODULE_ENABLED 295 #include "stm32f4xx_hal_nor.h" 296 #endif /* HAL_NOR_MODULE_ENABLED */ 297 298 #ifdef HAL_NAND_MODULE_ENABLED 299 #include "stm32f4xx_hal_nand.h" 300 #endif /* HAL_NAND_MODULE_ENABLED */ 301 302 #ifdef HAL_PCCARD_MODULE_ENABLED 303 #include "stm32f4xx_hal_pccard.h" 304 #endif /* HAL_PCCARD_MODULE_ENABLED */ 305 306 #ifdef HAL_SDRAM_MODULE_ENABLED 307 #include "stm32f4xx_hal_sdram.h" 308 #endif /* HAL_SDRAM_MODULE_ENABLED */ 309 310 #ifdef HAL_HASH_MODULE_ENABLED 311 #include "stm32f4xx_hal_hash.h" 312 #endif /* HAL_HASH_MODULE_ENABLED */ 313 314 #ifdef HAL_I2C_MODULE_ENABLED 315 #include "stm32f4xx_hal_i2c.h" 316 #endif /* HAL_I2C_MODULE_ENABLED */ 317 318 #ifdef HAL_I2S_MODULE_ENABLED 319 #include "stm32f4xx_hal_i2s.h" 320 #endif /* HAL_I2S_MODULE_ENABLED */ 321 322 #ifdef HAL_IWDG_MODULE_ENABLED 323 #include "stm32f4xx_hal_iwdg.h" 324 #endif /* HAL_IWDG_MODULE_ENABLED */ 325 326 #ifdef HAL_LTDC_MODULE_ENABLED 327 #include "stm32f4xx_hal_ltdc.h" 328 #endif /* HAL_LTDC_MODULE_ENABLED */ 329 330 #ifdef HAL_PWR_MODULE_ENABLED 331 #include "stm32f4xx_hal_pwr.h" 332 #endif /* HAL_PWR_MODULE_ENABLED */ 333 334 #ifdef HAL_RNG_MODULE_ENABLED 335 #include "stm32f4xx_hal_rng.h" 336 #endif /* HAL_RNG_MODULE_ENABLED */ 337 338 #ifdef HAL_RTC_MODULE_ENABLED 339 #include "stm32f4xx_hal_rtc.h" 340 #endif /* HAL_RTC_MODULE_ENABLED */ 341 342 #ifdef HAL_SAI_MODULE_ENABLED 343 #include "stm32f4xx_hal_sai.h" 344 #endif /* HAL_SAI_MODULE_ENABLED */ 345 346 #ifdef HAL_SD_MODULE_ENABLED 347 #include "stm32f4xx_hal_sd.h" 348 #endif /* HAL_SD_MODULE_ENABLED */ 349 350 #ifdef HAL_MMC_MODULE_ENABLED 351 #include "stm32f4xx_hal_mmc.h" 352 #endif /* HAL_MMC_MODULE_ENABLED */ 353 354 #ifdef HAL_SPI_MODULE_ENABLED 355 #include "stm32f4xx_hal_spi.h" 356 #endif /* HAL_SPI_MODULE_ENABLED */ 357 358 #ifdef HAL_TIM_MODULE_ENABLED 359 #include "stm32f4xx_hal_tim.h" 360 #endif /* HAL_TIM_MODULE_ENABLED */ 361 362 #ifdef HAL_UART_MODULE_ENABLED 363 #include "stm32f4xx_hal_uart.h" 364 #endif /* HAL_UART_MODULE_ENABLED */ 365 366 #ifdef HAL_USART_MODULE_ENABLED 367 #include "stm32f4xx_hal_usart.h" 368 #endif /* HAL_USART_MODULE_ENABLED */ 369 370 #ifdef HAL_IRDA_MODULE_ENABLED 371 #include "stm32f4xx_hal_irda.h" 372 #endif /* HAL_IRDA_MODULE_ENABLED */ 373 374 #ifdef HAL_SMARTCARD_MODULE_ENABLED 375 #include "stm32f4xx_hal_smartcard.h" 376 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 377 378 #ifdef HAL_WWDG_MODULE_ENABLED 379 #include "stm32f4xx_hal_wwdg.h" 380 #endif /* HAL_WWDG_MODULE_ENABLED */ 381 382 #ifdef HAL_PCD_MODULE_ENABLED 383 #include "stm32f4xx_hal_pcd.h" 384 #endif /* HAL_PCD_MODULE_ENABLED */ 385 386 #ifdef HAL_HCD_MODULE_ENABLED 387 #include "stm32f4xx_hal_hcd.h" 388 #endif /* HAL_HCD_MODULE_ENABLED */ 389 390 #ifdef HAL_DSI_MODULE_ENABLED 391 #include "stm32f4xx_hal_dsi.h" 392 #endif /* HAL_DSI_MODULE_ENABLED */ 393 394 #ifdef HAL_QSPI_MODULE_ENABLED 395 #include "stm32f4xx_hal_qspi.h" 396 #endif /* HAL_QSPI_MODULE_ENABLED */ 397 398 #ifdef HAL_CEC_MODULE_ENABLED 399 #include "stm32f4xx_hal_cec.h" 400 #endif /* HAL_CEC_MODULE_ENABLED */ 401 402 #ifdef HAL_FMPI2C_MODULE_ENABLED 403 #include "stm32f4xx_hal_fmpi2c.h" 404 #endif /* HAL_FMPI2C_MODULE_ENABLED */ 405 406 #ifdef HAL_SPDIFRX_MODULE_ENABLED 407 #include "stm32f4xx_hal_spdifrx.h" 408 #endif /* HAL_SPDIFRX_MODULE_ENABLED */ 409 410 #ifdef HAL_DFSDM_MODULE_ENABLED 411 #include "stm32f4xx_hal_dfsdm.h" 412 #endif /* HAL_DFSDM_MODULE_ENABLED */ 413 414 #ifdef HAL_LPTIM_MODULE_ENABLED 415 #include "stm32f4xx_hal_lptim.h" 416 #endif /* HAL_LPTIM_MODULE_ENABLED */ 417 418 /* Exported macro ------------------------------------------------------------*/ 419 #ifdef USE_FULL_ASSERT 420 /** 421 * @brief The assert_param macro is used for function's parameters check. 422 * @param expr: If expr is false, it calls assert_failed function 423 * which reports the name of the source file and the source 424 * line number of the call that failed. 425 * If expr is true, it returns no value. 426 * @retval None 427 */ 428 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 429 /* Exported functions ------------------------------------------------------- */ 430 void assert_failed(uint8_t* file, uint32_t line); 431 #else 432 #define assert_param(expr) ((void)0U) 433 #endif /* USE_FULL_ASSERT */ 434 435 #ifdef __cplusplus 436 } 437 #endif 438 439 #endif /* __STM32F4xx_HAL_CONF_H */ 440 441 442 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 443