1 /** 2 ****************************************************************************** 3 * @file stm32f7xx_hal_conf_template.h 4 * @author MCD Application Team 5 * @brief HAL configuration template file. 6 * This file should be copied to the application folder and renamed 7 * to stm32f7xx_hal_conf.h. 8 ****************************************************************************** 9 * @attention 10 * 11 * <h2><center>© Copyright (c) 2017 STMicroelectronics. 12 * All rights reserved.</center></h2> 13 * 14 * This software component is licensed by ST under BSD 3-Clause license, 15 * the "License"; You may not use this file except in compliance with the 16 * License. You may obtain a copy of the License at: 17 * opensource.org/licenses/BSD-3-Clause 18 * 19 ****************************************************************************** 20 */ 21 22 /* Define to prevent recursive inclusion -------------------------------------*/ 23 #ifndef __STM32F7xx_HAL_CONF_H 24 #define __STM32F7xx_HAL_CONF_H 25 26 #ifdef __cplusplus 27 extern "C" { 28 #endif 29 30 /* Exported types ------------------------------------------------------------*/ 31 /* Exported constants --------------------------------------------------------*/ 32 33 /* ########################## Module Selection ############################## */ 34 /** 35 * @brief This is the list of modules to be used in the HAL driver 36 */ 37 #define HAL_MODULE_ENABLED 38 39 #define HAL_ADC_MODULE_ENABLED 40 /* #define HAL_CRYP_MODULE_ENABLED */ 41 /* #define HAL_CAN_MODULE_ENABLED */ 42 /* #define HAL_CEC_MODULE_ENABLED */ 43 /* #define HAL_CRC_MODULE_ENABLED */ 44 /* #define HAL_CRYP_MODULE_ENABLED */ 45 /* #define HAL_DAC_MODULE_ENABLED */ 46 /* #define HAL_DCMI_MODULE_ENABLED */ 47 /* #define HAL_DMA2D_MODULE_ENABLED */ 48 #define HAL_ETH_MODULE_ENABLED 49 /* #define HAL_NAND_MODULE_ENABLED */ 50 /* #define HAL_NOR_MODULE_ENABLED */ 51 /* #define HAL_SRAM_MODULE_ENABLED */ 52 #define HAL_SDRAM_MODULE_ENABLED 53 /* #define HAL_HASH_MODULE_ENABLED */ 54 /* #define HAL_I2S_MODULE_ENABLED */ 55 #define HAL_IWDG_MODULE_ENABLED 56 /* #define HAL_LPTIM_MODULE_ENABLED */ 57 #define HAL_LTDC_MODULE_ENABLED 58 #define HAL_QSPI_MODULE_ENABLED 59 /* #define HAL_RNG_MODULE_ENABLED */ 60 #define HAL_RTC_MODULE_ENABLED 61 /* #define HAL_SAI_MODULE_ENABLED */ 62 #define HAL_SD_MODULE_ENABLED 63 /* #define HAL_MMC_MODULE_ENABLED */ 64 /* #define HAL_SPDIFRX_MODULE_ENABLED */ 65 #define HAL_SPI_MODULE_ENABLED 66 #define HAL_TIM_MODULE_ENABLED 67 #define HAL_UART_MODULE_ENABLED 68 /* #define HAL_USART_MODULE_ENABLED */ 69 /* #define HAL_IRDA_MODULE_ENABLED */ 70 /* #define HAL_SMARTCARD_MODULE_ENABLED */ 71 /* #define HAL_WWDG_MODULE_ENABLED */ 72 /* #define HAL_PCD_MODULE_ENABLED */ 73 #define HAL_HCD_MODULE_ENABLED 74 /* #define HAL_DFSDM_MODULE_ENABLED */ 75 /* #define HAL_DSI_MODULE_ENABLED */ 76 /* #define HAL_JPEG_MODULE_ENABLED */ 77 /* #define HAL_MDIOS_MODULE_ENABLED */ 78 /* #define HAL_SMBUS_MODULE_ENABLED */ 79 /* #define HAL_EXTI_MODULE_ENABLED */ 80 #define HAL_GPIO_MODULE_ENABLED 81 #define HAL_EXTI_MODULE_ENABLED 82 #define HAL_DMA_MODULE_ENABLED 83 #define HAL_RCC_MODULE_ENABLED 84 #define HAL_FLASH_MODULE_ENABLED 85 #define HAL_PWR_MODULE_ENABLED 86 #define HAL_I2C_MODULE_ENABLED 87 #define HAL_CORTEX_MODULE_ENABLED 88 89 /* ########################## HSE/HSI Values adaptation ##################### */ 90 /** 91 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 92 * This value is used by the RCC HAL module to compute the system frequency 93 * (when HSE is used as system clock source, directly or through the PLL). 94 */ 95 #if !defined (HSE_VALUE) 96 #define HSE_VALUE ((uint32_t)25000000U) /*!< Value of the External oscillator in Hz */ 97 #endif /* HSE_VALUE */ 98 99 #if !defined (HSE_STARTUP_TIMEOUT) 100 #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ 101 #endif /* HSE_STARTUP_TIMEOUT */ 102 103 /** 104 * @brief Internal High Speed oscillator (HSI) value. 105 * This value is used by the RCC HAL module to compute the system frequency 106 * (when HSI is used as system clock source, directly or through the PLL). 107 */ 108 #if !defined (HSI_VALUE) 109 #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ 110 #endif /* HSI_VALUE */ 111 112 /** 113 * @brief Internal Low Speed oscillator (LSI) value. 114 */ 115 #if !defined (LSI_VALUE) 116 #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ 117 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 118 The real value may vary depending on the variations 119 in voltage and temperature. */ 120 /** 121 * @brief External Low Speed oscillator (LSE) value. 122 */ 123 #if !defined (LSE_VALUE) 124 #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ 125 #endif /* LSE_VALUE */ 126 127 #if !defined (LSE_STARTUP_TIMEOUT) 128 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ 129 #endif /* LSE_STARTUP_TIMEOUT */ 130 131 /** 132 * @brief External clock source for I2S peripheral 133 * This value is used by the I2S HAL module to compute the I2S clock source 134 * frequency, this source is inserted directly through I2S_CKIN pad. 135 */ 136 #if !defined (EXTERNAL_CLOCK_VALUE) 137 #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/ 138 #endif /* EXTERNAL_CLOCK_VALUE */ 139 140 /* Tip: To avoid modifying this file each time you need to use different HSE, 141 === you can define the HSE value in your toolchain compiler preprocessor. */ 142 143 /* ########################### System Configuration ######################### */ 144 /** 145 * @brief This is the HAL system configuration section 146 */ 147 #define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ 148 #define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */ 149 #define USE_RTOS 0U 150 #define PREFETCH_ENABLE 1U 151 #define ART_ACCLERATOR_ENABLE 1U /* To enable instruction cache and prefetch */ 152 153 /* ########################## Assert Selection ############################## */ 154 /** 155 * @brief Uncomment the line below to expanse the "assert_param" macro in the 156 * HAL drivers code 157 */ 158 /* #define USE_FULL_ASSERT 1U */ 159 160 /* ################## Ethernet peripheral configuration ##################### */ 161 162 /* Section 1 : Ethernet peripheral configuration */ 163 164 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 165 #define MAC_ADDR0 2U 166 #define MAC_ADDR1 0U 167 #define MAC_ADDR2 0U 168 #define MAC_ADDR3 0U 169 #define MAC_ADDR4 0U 170 #define MAC_ADDR5 0U 171 172 /* Definition of the Ethernet driver buffers size and count */ 173 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 174 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 175 #define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 176 #define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 177 178 /* Section 2: PHY configuration section */ 179 180 /* LAN8742A_PHY_ADDRESS Address*/ 181 #define LAN8742A_PHY_ADDRESS 1 182 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 183 #define PHY_RESET_DELAY ((uint32_t)0x000000FFU) 184 /* PHY Configuration delay */ 185 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU) 186 187 #define PHY_READ_TO ((uint32_t)0x0000FFFFU) 188 #define PHY_WRITE_TO ((uint32_t)0x0000FFFFU) 189 190 /* Section 3: Common PHY Registers */ 191 192 #define PHY_BCR ((uint16_t)0x00U) /*!< Transceiver Basic Control Register */ 193 #define PHY_BSR ((uint16_t)0x01U) /*!< Transceiver Basic Status Register */ 194 195 #define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */ 196 #define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */ 197 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */ 198 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */ 199 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */ 200 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */ 201 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */ 202 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */ 203 #define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */ 204 #define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */ 205 206 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */ 207 #define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */ 208 #define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */ 209 210 /* Section 4: Extended PHY Registers */ 211 #define PHY_SR ((uint16_t)0x1FU) /*!< PHY status register Offset */ 212 213 #define PHY_SPEED_STATUS ((uint16_t)0x0004U) /*!< PHY Speed mask */ 214 #define PHY_DUPLEX_STATUS ((uint16_t)0x0010U) /*!< PHY Duplex mask */ 215 216 #define PHY_ISFR ((uint16_t)0x001DU) /*!< PHY Interrupt Source Flag register Offset */ 217 #define PHY_ISFR_INT4 ((uint16_t)0x000BU) /*!< PHY Link down inturrupt */ 218 219 /* ################## SPI peripheral configuration ########################## */ 220 221 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 222 * Activated: CRC code is present inside driver 223 * Deactivated: CRC code cleaned from driver 224 */ 225 226 #define USE_SPI_CRC 0U 227 228 /* Includes ------------------------------------------------------------------*/ 229 /** 230 * @brief Include module's header file 231 */ 232 233 #ifdef HAL_RCC_MODULE_ENABLED 234 #include "stm32f7xx_hal_rcc.h" 235 #endif /* HAL_RCC_MODULE_ENABLED */ 236 237 #ifdef HAL_EXTI_MODULE_ENABLED 238 #include "stm32f7xx_hal_exti.h" 239 #endif /* HAL_EXTI_MODULE_ENABLED */ 240 241 #ifdef HAL_GPIO_MODULE_ENABLED 242 #include "stm32f7xx_hal_gpio.h" 243 #endif /* HAL_GPIO_MODULE_ENABLED */ 244 245 #ifdef HAL_DMA_MODULE_ENABLED 246 #include "stm32f7xx_hal_dma.h" 247 #endif /* HAL_DMA_MODULE_ENABLED */ 248 249 #ifdef HAL_CORTEX_MODULE_ENABLED 250 #include "stm32f7xx_hal_cortex.h" 251 #endif /* HAL_CORTEX_MODULE_ENABLED */ 252 253 #ifdef HAL_ADC_MODULE_ENABLED 254 #include "stm32f7xx_hal_adc.h" 255 #endif /* HAL_ADC_MODULE_ENABLED */ 256 257 #ifdef HAL_CAN_MODULE_ENABLED 258 #include "stm32f7xx_hal_can.h" 259 #endif /* HAL_CAN_MODULE_ENABLED */ 260 261 #ifdef HAL_CEC_MODULE_ENABLED 262 #include "stm32f7xx_hal_cec.h" 263 #endif /* HAL_CEC_MODULE_ENABLED */ 264 265 #ifdef HAL_CRC_MODULE_ENABLED 266 #include "stm32f7xx_hal_crc.h" 267 #endif /* HAL_CRC_MODULE_ENABLED */ 268 269 #ifdef HAL_CRYP_MODULE_ENABLED 270 #include "stm32f7xx_hal_cryp.h" 271 #endif /* HAL_CRYP_MODULE_ENABLED */ 272 273 #ifdef HAL_DMA2D_MODULE_ENABLED 274 #include "stm32f7xx_hal_dma2d.h" 275 #endif /* HAL_DMA2D_MODULE_ENABLED */ 276 277 #ifdef HAL_DAC_MODULE_ENABLED 278 #include "stm32f7xx_hal_dac.h" 279 #endif /* HAL_DAC_MODULE_ENABLED */ 280 281 #ifdef HAL_DCMI_MODULE_ENABLED 282 #include "stm32f7xx_hal_dcmi.h" 283 #endif /* HAL_DCMI_MODULE_ENABLED */ 284 285 #ifdef HAL_ETH_MODULE_ENABLED 286 #include "stm32f7xx_hal_eth.h" 287 #endif /* HAL_ETH_MODULE_ENABLED */ 288 289 #ifdef HAL_FLASH_MODULE_ENABLED 290 #include "stm32f7xx_hal_flash.h" 291 #endif /* HAL_FLASH_MODULE_ENABLED */ 292 293 #ifdef HAL_SRAM_MODULE_ENABLED 294 #include "stm32f7xx_hal_sram.h" 295 #endif /* HAL_SRAM_MODULE_ENABLED */ 296 297 #ifdef HAL_NOR_MODULE_ENABLED 298 #include "stm32f7xx_hal_nor.h" 299 #endif /* HAL_NOR_MODULE_ENABLED */ 300 301 #ifdef HAL_NAND_MODULE_ENABLED 302 #include "stm32f7xx_hal_nand.h" 303 #endif /* HAL_NAND_MODULE_ENABLED */ 304 305 #ifdef HAL_SDRAM_MODULE_ENABLED 306 #include "stm32f7xx_hal_sdram.h" 307 #endif /* HAL_SDRAM_MODULE_ENABLED */ 308 309 #ifdef HAL_HASH_MODULE_ENABLED 310 #include "stm32f7xx_hal_hash.h" 311 #endif /* HAL_HASH_MODULE_ENABLED */ 312 313 #ifdef HAL_I2C_MODULE_ENABLED 314 #include "stm32f7xx_hal_i2c.h" 315 #endif /* HAL_I2C_MODULE_ENABLED */ 316 317 #ifdef HAL_I2S_MODULE_ENABLED 318 #include "stm32f7xx_hal_i2s.h" 319 #endif /* HAL_I2S_MODULE_ENABLED */ 320 321 #ifdef HAL_IWDG_MODULE_ENABLED 322 #include "stm32f7xx_hal_iwdg.h" 323 #endif /* HAL_IWDG_MODULE_ENABLED */ 324 325 #ifdef HAL_LPTIM_MODULE_ENABLED 326 #include "stm32f7xx_hal_lptim.h" 327 #endif /* HAL_LPTIM_MODULE_ENABLED */ 328 329 #ifdef HAL_LTDC_MODULE_ENABLED 330 #include "stm32f7xx_hal_ltdc.h" 331 #endif /* HAL_LTDC_MODULE_ENABLED */ 332 333 #ifdef HAL_PWR_MODULE_ENABLED 334 #include "stm32f7xx_hal_pwr.h" 335 #endif /* HAL_PWR_MODULE_ENABLED */ 336 337 #ifdef HAL_QSPI_MODULE_ENABLED 338 #include "stm32f7xx_hal_qspi.h" 339 #endif /* HAL_QSPI_MODULE_ENABLED */ 340 341 #ifdef HAL_RNG_MODULE_ENABLED 342 #include "stm32f7xx_hal_rng.h" 343 #endif /* HAL_RNG_MODULE_ENABLED */ 344 345 #ifdef HAL_RTC_MODULE_ENABLED 346 #include "stm32f7xx_hal_rtc.h" 347 #endif /* HAL_RTC_MODULE_ENABLED */ 348 349 #ifdef HAL_SAI_MODULE_ENABLED 350 #include "stm32f7xx_hal_sai.h" 351 #endif /* HAL_SAI_MODULE_ENABLED */ 352 353 #ifdef HAL_SD_MODULE_ENABLED 354 #include "stm32f7xx_hal_sd.h" 355 #endif /* HAL_SD_MODULE_ENABLED */ 356 357 #ifdef HAL_MMC_MODULE_ENABLED 358 #include "stm32f7xx_hal_mmc.h" 359 #endif /* HAL_MMC_MODULE_ENABLED */ 360 361 #ifdef HAL_SPDIFRX_MODULE_ENABLED 362 #include "stm32f7xx_hal_spdifrx.h" 363 #endif /* HAL_SPDIFRX_MODULE_ENABLED */ 364 365 #ifdef HAL_SPI_MODULE_ENABLED 366 #include "stm32f7xx_hal_spi.h" 367 #endif /* HAL_SPI_MODULE_ENABLED */ 368 369 #ifdef HAL_TIM_MODULE_ENABLED 370 #include "stm32f7xx_hal_tim.h" 371 #endif /* HAL_TIM_MODULE_ENABLED */ 372 373 #ifdef HAL_UART_MODULE_ENABLED 374 #include "stm32f7xx_hal_uart.h" 375 #endif /* HAL_UART_MODULE_ENABLED */ 376 377 #ifdef HAL_USART_MODULE_ENABLED 378 #include "stm32f7xx_hal_usart.h" 379 #endif /* HAL_USART_MODULE_ENABLED */ 380 381 #ifdef HAL_IRDA_MODULE_ENABLED 382 #include "stm32f7xx_hal_irda.h" 383 #endif /* HAL_IRDA_MODULE_ENABLED */ 384 385 #ifdef HAL_SMARTCARD_MODULE_ENABLED 386 #include "stm32f7xx_hal_smartcard.h" 387 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 388 389 #ifdef HAL_WWDG_MODULE_ENABLED 390 #include "stm32f7xx_hal_wwdg.h" 391 #endif /* HAL_WWDG_MODULE_ENABLED */ 392 393 #ifdef HAL_PCD_MODULE_ENABLED 394 #include "stm32f7xx_hal_pcd.h" 395 #endif /* HAL_PCD_MODULE_ENABLED */ 396 397 #ifdef HAL_HCD_MODULE_ENABLED 398 #include "stm32f7xx_hal_hcd.h" 399 #endif /* HAL_HCD_MODULE_ENABLED */ 400 401 #ifdef HAL_DFSDM_MODULE_ENABLED 402 #include "stm32f7xx_hal_dfsdm.h" 403 #endif /* HAL_DFSDM_MODULE_ENABLED */ 404 405 #ifdef HAL_DSI_MODULE_ENABLED 406 #include "stm32f7xx_hal_dsi.h" 407 #endif /* HAL_DSI_MODULE_ENABLED */ 408 409 #ifdef HAL_JPEG_MODULE_ENABLED 410 #include "stm32f7xx_hal_jpeg.h" 411 #endif /* HAL_JPEG_MODULE_ENABLED */ 412 413 #ifdef HAL_MDIOS_MODULE_ENABLED 414 #include "stm32f7xx_hal_mdios.h" 415 #endif /* HAL_MDIOS_MODULE_ENABLED */ 416 417 #ifdef HAL_SMBUS_MODULE_ENABLED 418 #include "stm32f7xx_hal_smbus.h" 419 #endif /* HAL_SMBUS_MODULE_ENABLED */ 420 421 /* Exported macro ------------------------------------------------------------*/ 422 #ifdef USE_FULL_ASSERT 423 /** 424 * @brief The assert_param macro is used for function's parameters check. 425 * @param expr: If expr is false, it calls assert_failed function 426 * which reports the name of the source file and the source 427 * line number of the call that failed. 428 * If expr is true, it returns no value. 429 * @retval None 430 */ 431 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 432 /* Exported functions ------------------------------------------------------- */ 433 void assert_failed(uint8_t* file, uint32_t line); 434 #else 435 #define assert_param(expr) ((void)0U) 436 #endif /* USE_FULL_ASSERT */ 437 438 #ifdef __cplusplus 439 } 440 #endif 441 442 #endif /* __STM32F7xx_HAL_CONF_H */ 443 444 445 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 446