1 /**
2   ******************************************************************************
3   * @file    stm32g0xx_hal_conf.h
4   * @author  MCD Application Team
5   * @brief   HAL configuration file.
6   ******************************************************************************
7   * @attention
8   *
9   * <h2><center>&copy; Copyright (c) 2018 STMicroelectronics.
10   * All rights reserved.</center></h2>
11   *
12   * This software component is licensed by ST under BSD 3-Clause license,
13   * the "License"; You may not use this file except in compliance with the
14   * License. You may obtain a copy of the License at:
15   *                        opensource.org/licenses/BSD-3-Clause
16   *
17   ******************************************************************************
18   */
19 
20 /* Define to prevent recursive inclusion -------------------------------------*/
21 #ifndef STM32G0xx_HAL_CONF_H
22 #define STM32G0xx_HAL_CONF_H
23 
24 #ifdef __cplusplus
25 extern "C" {
26 #endif
27 
28 /* Exported types ------------------------------------------------------------*/
29 /* Exported constants --------------------------------------------------------*/
30 
31 /* ########################## Module Selection ############################## */
32 /**
33   * @brief This is the list of modules to be used in the HAL driver
34   */
35 #define HAL_MODULE_ENABLED
36 
37   #define HAL_ADC_MODULE_ENABLED
38 /* #define HAL_CEC_MODULE_ENABLED   */
39 /* #define HAL_COMP_MODULE_ENABLED   */
40 /* #define HAL_CRC_MODULE_ENABLED   */
41 /* #define HAL_CRYP_MODULE_ENABLED   */
42 /* #define HAL_DAC_MODULE_ENABLED   */
43 /* #define HAL_EXTI_MODULE_ENABLED   */
44 /* #define HAL_I2C_MODULE_ENABLED   */
45 /* #define HAL_I2S_MODULE_ENABLED   */
46 #define HAL_IWDG_MODULE_ENABLED
47 /* #define HAL_IRDA_MODULE_ENABLED   */
48 /* #define HAL_LPTIM_MODULE_ENABLED   */
49 /* #define HAL_RNG_MODULE_ENABLED   */
50 #define HAL_RTC_MODULE_ENABLED
51 /* #define HAL_SMARTCARD_MODULE_ENABLED   */
52 /* #define HAL_SMBUS_MODULE_ENABLED   */
53 #define HAL_SPI_MODULE_ENABLED
54 #define HAL_TIM_MODULE_ENABLED
55 #define HAL_UART_MODULE_ENABLED
56 /* #define HAL_USART_MODULE_ENABLED   */
57 #define HAL_WWDG_MODULE_ENABLED
58 #define HAL_GPIO_MODULE_ENABLED
59 #define HAL_EXTI_MODULE_ENABLED
60 #define HAL_DMA_MODULE_ENABLED
61 #define HAL_RCC_MODULE_ENABLED
62 #define HAL_FLASH_MODULE_ENABLED
63 #define HAL_PWR_MODULE_ENABLED
64 #define HAL_CORTEX_MODULE_ENABLED
65 
66 /* ########################## Register Callbacks selection ############################## */
67 /**
68   * @brief This is the list of modules where register callback can be used
69   */
70 #define USE_HAL_ADC_REGISTER_CALLBACKS    0u
71 #define USE_HAL_CEC_REGISTER_CALLBACKS    0u
72 #define USE_HAL_COMP_REGISTER_CALLBACKS   0u
73 #define USE_HAL_CRYP_REGISTER_CALLBACKS   0u
74 #define USE_HAL_DAC_REGISTER_CALLBACKS    0u
75 #define USE_HAL_I2C_REGISTER_CALLBACKS    0u
76 #define USE_HAL_I2S_REGISTER_CALLBACKS    0u
77 #define USE_HAL_IRDA_REGISTER_CALLBACKS   0u
78 #define USE_HAL_LPTIM_REGISTER_CALLBACKS  0u
79 #define USE_HAL_RNG_REGISTER_CALLBACKS    0u
80 #define USE_HAL_RTC_REGISTER_CALLBACKS    0u
81 #define USE_HAL_SMBUS_REGISTER_CALLBACKS  0u
82 #define USE_HAL_SPI_REGISTER_CALLBACKS    0u
83 #define USE_HAL_TIM_REGISTER_CALLBACKS    0u
84 #define USE_HAL_UART_REGISTER_CALLBACKS   0u
85 #define USE_HAL_USART_REGISTER_CALLBACKS  0u
86 #define USE_HAL_WWDG_REGISTER_CALLBACKS   0u
87 
88 /* ########################## Oscillator Values adaptation ####################*/
89 /**
90   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
91   *        This value is used by the RCC HAL module to compute the system frequency
92   *        (when HSE is used as system clock source, directly or through the PLL).
93   */
94 #if !defined  (HSE_VALUE)
95 #define HSE_VALUE    8000000U         /*!< Value of the External oscillator in Hz */
96 #endif /* HSE_VALUE */
97 
98 #if !defined  (HSE_STARTUP_TIMEOUT)
99 #define HSE_STARTUP_TIMEOUT    100U         /*!< Time out for HSE start up, in ms */
100 #endif /* HSE_STARTUP_TIMEOUT */
101 
102 /**
103   * @brief Internal High Speed oscillator (HSI) value.
104   *        This value is used by the RCC HAL module to compute the system frequency
105   *        (when HSI is used as system clock source, directly or through the PLL).
106   */
107 #if !defined  (HSI_VALUE)
108 #define HSI_VALUE    16000000U            /*!< Value of the Internal oscillator in Hz*/
109 #endif /* HSI_VALUE */
110 
111 /**
112   * @brief Internal Low Speed oscillator (LSI) value.
113   */
114 #if !defined  (LSI_VALUE)
115 #define LSI_VALUE  32000U                  /*!< LSI Typical Value in Hz*/
116 #endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz
117 The real value may vary depending on the variations
118 in voltage and temperature.*/
119 /**
120   * @brief External Low Speed oscillator (LSE) value.
121   *        This value is used by the UART, RTC HAL module to compute the system frequency
122   */
123 #if !defined  (LSE_VALUE)
124 #define LSE_VALUE    32768U               /*!< Value of the External oscillator in Hz*/
125 #endif /* LSE_VALUE */
126 
127 #if !defined  (LSE_STARTUP_TIMEOUT)
128 #define LSE_STARTUP_TIMEOUT    5000U      /*!< Time out for LSE start up, in ms */
129 #endif /* LSE_STARTUP_TIMEOUT */
130 
131 /**
132   * @brief External clock source for I2S1 peripheral
133   *        This value is used by the RCC HAL module to compute the I2S1 clock source
134   *        frequency.
135   */
136 #if !defined  (EXTERNAL_I2S1_CLOCK_VALUE)
137 #define EXTERNAL_I2S1_CLOCK_VALUE    12288000U /*!< Value of the I2S1 External clock source in Hz*/
138 #endif /* EXTERNAL_I2S1_CLOCK_VALUE */
139 
140 /* Tip: To avoid modifying this file each time you need to use different HSE,
141    ===  you can define the HSE value in your toolchain compiler preprocessor. */
142 
143 /* ########################### System Configuration ######################### */
144 /**
145   * @brief This is the HAL system configuration section
146   */
147 #define  VDD_VALUE                    3300U                                         /*!< Value of VDD in mv */
148 #define  TICK_INT_PRIORITY            0U /*!< tick interrupt priority */
149 #define  USE_RTOS                     0U
150 #define  PREFETCH_ENABLE              1U
151 #define  INSTRUCTION_CACHE_ENABLE     1U
152 
153 /* ################## SPI peripheral configuration ########################## */
154 
155 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
156 * Activated: CRC code is present inside driver
157 * Deactivated: CRC code cleaned from driver
158 */
159 
160 #define USE_SPI_CRC                     0U
161 
162 /* ################## CRYP peripheral configuration ########################## */
163 
164 #define USE_HAL_CRYP_SUSPEND_RESUME     1U
165 
166 /* ########################## Assert Selection ############################## */
167 /**
168   * @brief Uncomment the line below to expanse the "assert_param" macro in the
169   *        HAL drivers code
170   */
171 /* #define USE_FULL_ASSERT    1U */
172 
173 /* Includes ------------------------------------------------------------------*/
174 /**
175   * @brief Include module's header file
176   */
177 
178 #ifdef HAL_RCC_MODULE_ENABLED
179 #include "stm32g0xx_hal_rcc.h"
180 #endif /* HAL_RCC_MODULE_ENABLED */
181 
182 #ifdef HAL_GPIO_MODULE_ENABLED
183 #include "stm32g0xx_hal_gpio.h"
184 #endif /* HAL_GPIO_MODULE_ENABLED */
185 
186 #ifdef HAL_DMA_MODULE_ENABLED
187 #include "stm32g0xx_hal_dma.h"
188 #endif /* HAL_DMA_MODULE_ENABLED */
189 
190 #ifdef HAL_CORTEX_MODULE_ENABLED
191 #include "stm32g0xx_hal_cortex.h"
192 #endif /* HAL_CORTEX_MODULE_ENABLED */
193 
194 #ifdef HAL_ADC_MODULE_ENABLED
195 #include "stm32g0xx_hal_adc.h"
196 #include "stm32g0xx_hal_adc_ex.h"
197 #endif /* HAL_ADC_MODULE_ENABLED */
198 
199 #ifdef HAL_CEC_MODULE_ENABLED
200 #include "stm32g0xx_hal_cec.h"
201 #endif /* HAL_CEC_MODULE_ENABLED */
202 
203 #ifdef HAL_COMP_MODULE_ENABLED
204 #include "stm32g0xx_hal_comp.h"
205 #endif /* HAL_COMP_MODULE_ENABLED */
206 
207 #ifdef HAL_CRC_MODULE_ENABLED
208 #include "stm32g0xx_hal_crc.h"
209 #endif /* HAL_CRC_MODULE_ENABLED */
210 
211 #ifdef HAL_CRYP_MODULE_ENABLED
212 #include "stm32g0xx_hal_cryp.h"
213 #endif /* HAL_CRYP_MODULE_ENABLED */
214 
215 #ifdef HAL_DAC_MODULE_ENABLED
216 #include "stm32g0xx_hal_dac.h"
217 #endif /* HAL_DAC_MODULE_ENABLED */
218 
219 #ifdef HAL_EXTI_MODULE_ENABLED
220 #include "stm32g0xx_hal_exti.h"
221 #endif /* HAL_EXTI_MODULE_ENABLED */
222 
223 #ifdef HAL_FLASH_MODULE_ENABLED
224 #include "stm32g0xx_hal_flash.h"
225 #endif /* HAL_FLASH_MODULE_ENABLED */
226 
227 #ifdef HAL_I2C_MODULE_ENABLED
228 #include "stm32g0xx_hal_i2c.h"
229 #endif /* HAL_I2C_MODULE_ENABLED */
230 
231 #ifdef HAL_I2S_MODULE_ENABLED
232 #include "stm32g0xx_hal_i2s.h"
233 #endif /* HAL_I2S_MODULE_ENABLED */
234 
235 #ifdef HAL_IRDA_MODULE_ENABLED
236 #include "stm32g0xx_hal_irda.h"
237 #endif /* HAL_IRDA_MODULE_ENABLED */
238 
239 #ifdef HAL_IWDG_MODULE_ENABLED
240 #include "stm32g0xx_hal_iwdg.h"
241 #endif /* HAL_IWDG_MODULE_ENABLED */
242 
243 #ifdef HAL_LPTIM_MODULE_ENABLED
244 #include "stm32g0xx_hal_lptim.h"
245 #endif /* HAL_LPTIM_MODULE_ENABLED */
246 
247 #ifdef HAL_PWR_MODULE_ENABLED
248 #include "stm32g0xx_hal_pwr.h"
249 #endif /* HAL_PWR_MODULE_ENABLED */
250 
251 #ifdef HAL_RNG_MODULE_ENABLED
252 #include "stm32g0xx_hal_rng.h"
253 #endif /* HAL_RNG_MODULE_ENABLED */
254 
255 #ifdef HAL_RTC_MODULE_ENABLED
256 #include "stm32g0xx_hal_rtc.h"
257 #endif /* HAL_RTC_MODULE_ENABLED */
258 
259 #ifdef HAL_SMARTCARD_MODULE_ENABLED
260 #include "stm32g0xx_hal_smartcard.h"
261 #endif /* HAL_SMARTCARD_MODULE_ENABLED */
262 
263 #ifdef HAL_SMBUS_MODULE_ENABLED
264 #include "stm32g0xx_hal_smbus.h"
265 #endif /* HAL_SMBUS_MODULE_ENABLED */
266 
267 #ifdef HAL_SPI_MODULE_ENABLED
268 #include "stm32g0xx_hal_spi.h"
269 #endif /* HAL_SPI_MODULE_ENABLED */
270 
271 #ifdef HAL_TIM_MODULE_ENABLED
272 #include "stm32g0xx_hal_tim.h"
273 #endif /* HAL_TIM_MODULE_ENABLED */
274 
275 #ifdef HAL_UART_MODULE_ENABLED
276 #include "stm32g0xx_hal_uart.h"
277 #endif /* HAL_UART_MODULE_ENABLED */
278 
279 #ifdef HAL_USART_MODULE_ENABLED
280 #include "stm32g0xx_hal_usart.h"
281 #endif /* HAL_USART_MODULE_ENABLED */
282 
283 #ifdef HAL_WWDG_MODULE_ENABLED
284 #include "stm32g0xx_hal_wwdg.h"
285 #endif /* HAL_WWDG_MODULE_ENABLED */
286 
287 /* Exported macro ------------------------------------------------------------*/
288 #ifdef  USE_FULL_ASSERT
289 /**
290   * @brief  The assert_param macro is used for functions parameters check.
291   * @param  expr If expr is false, it calls assert_failed function
292   *         which reports the name of the source file and the source
293   *         line number of the call that failed.
294   *         If expr is true, it returns no value.
295   * @retval None
296   */
297 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
298 /* Exported functions ------------------------------------------------------- */
299 void assert_failed(uint8_t *file, uint32_t line);
300 #else
301 #define assert_param(expr) ((void)0U)
302 #endif /* USE_FULL_ASSERT */
303 
304 #ifdef __cplusplus
305 }
306 #endif
307 
308 #endif /* STM32G0xx_HAL_CONF_H */
309 
310 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
311