1 /** 2 ****************************************************************************** 3 * @file stm32wlxx_hal_conf.h 4 * @author MCD Application Team 5 * @brief HAL configuration file. 6 ****************************************************************************** 7 * @attention 8 * 9 * <h2><center>© Copyright (c) 2020 STMicroelectronics. 10 * All rights reserved.</center></h2> 11 * 12 * This software component is licensed by ST under BSD 3-Clause license, 13 * the "License"; You may not use this file except in compliance with the 14 * License. You may obtain a copy of the License at: 15 * opensource.org/licenses/BSD-3-Clause 16 * 17 ****************************************************************************** 18 */ 19 20 /* Define to prevent recursive inclusion -------------------------------------*/ 21 #ifndef STM32WLxx_HAL_CONF_H 22 #define STM32WLxx_HAL_CONF_H 23 24 #ifdef __cplusplus 25 extern "C" { 26 #endif 27 28 /* Exported types ------------------------------------------------------------*/ 29 /* Exported constants --------------------------------------------------------*/ 30 31 /* ########################## Module Selection ############################## */ 32 /** 33 * @brief This is the list of modules to be used in the HAL driver 34 */ 35 #define HAL_MODULE_ENABLED 36 /*#define HAL_ADC_MODULE_ENABLED */ 37 /*#define HAL_COMP_MODULE_ENABLED */ 38 /*#define HAL_CRC_MODULE_ENABLED */ 39 /*#define HAL_CRYP_MODULE_ENABLED */ 40 /*#define HAL_DAC_MODULE_ENABLED */ 41 /*#define HAL_GTZC_MODULE_ENABLED */ 42 /*#define HAL_HSEM_MODULE_ENABLED */ 43 /*#define HAL_I2C_MODULE_ENABLED */ 44 /*#define HAL_I2S_MODULE_ENABLED */ 45 /*#define HAL_IPCC_MODULE_ENABLED */ 46 /*#define HAL_IRDA_MODULE_ENABLED */ 47 /*#define HAL_IWDG_MODULE_ENABLED */ 48 /*#define HAL_LPTIM_MODULE_ENABLED */ 49 /*#define HAL_PKA_MODULE_ENABLED */ 50 /*#define HAL_RNG_MODULE_ENABLED */ 51 /*#define HAL_RTC_MODULE_ENABLED */ 52 /*#define HAL_SMARTCARD_MODULE_ENABLED */ 53 /*#define HAL_SMBUS_MODULE_ENABLED */ 54 /*#define HAL_SPI_MODULE_ENABLED */ 55 /*#define HAL_SUBGHZ_MODULE_ENABLED */ 56 /*#define HAL_TIM_MODULE_ENABLED */ 57 #define HAL_UART_MODULE_ENABLED 58 /*#define HAL_USART_MODULE_ENABLED */ 59 /*#define HAL_WWDG_MODULE_ENABLED */ 60 #define HAL_EXTI_MODULE_ENABLED 61 #define HAL_CORTEX_MODULE_ENABLED 62 #define HAL_DMA_MODULE_ENABLED 63 #define HAL_FLASH_MODULE_ENABLED 64 #define HAL_GPIO_MODULE_ENABLED 65 #define HAL_PWR_MODULE_ENABLED 66 #define HAL_RCC_MODULE_ENABLED 67 68 /* ########################## Register Callbacks selection ############################## */ 69 /** 70 * @brief This is the list of modules where register callback can be used 71 */ 72 #define USE_HAL_ADC_REGISTER_CALLBACKS 0u 73 #define USE_HAL_COMP_REGISTER_CALLBACKS 0u 74 #define USE_HAL_CRYP_REGISTER_CALLBACKS 0u 75 #define USE_HAL_DAC_REGISTER_CALLBACKS 0u 76 #define USE_HAL_I2C_REGISTER_CALLBACKS 0u 77 #define USE_HAL_I2S_REGISTER_CALLBACKS 0u 78 #define USE_HAL_IRDA_REGISTER_CALLBACKS 0u 79 #define USE_HAL_LPTIM_REGISTER_CALLBACKS 0u 80 #define USE_HAL_PKA_REGISTER_CALLBACKS 0u 81 #define USE_HAL_RNG_REGISTER_CALLBACKS 0u 82 #define USE_HAL_RTC_REGISTER_CALLBACKS 0u 83 #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0u 84 #define USE_HAL_SMBUS_REGISTER_CALLBACKS 0u 85 #define USE_HAL_SPI_REGISTER_CALLBACKS 0u 86 #define USE_HAL_SUBGHZ_REGISTER_CALLBACKS 0u 87 #define USE_HAL_TIM_REGISTER_CALLBACKS 0u 88 #define USE_HAL_UART_REGISTER_CALLBACKS 0u 89 #define USE_HAL_USART_REGISTER_CALLBACKS 0u 90 #define USE_HAL_WWDG_REGISTER_CALLBACKS 0u 91 92 /* ########################## Oscillator Values adaptation ####################*/ 93 /** 94 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 95 * This value is used by the RCC HAL module to compute the system frequency 96 * (when HSE is used as system clock source, directly or through the PLL). 97 */ 98 99 #if !defined (HSE_VALUE) 100 #define HSE_VALUE 32000000UL /*!< Value of the External oscillator in Hz */ 101 #endif /* HSE_VALUE */ 102 103 #if !defined (HSE_STARTUP_TIMEOUT) 104 #define HSE_STARTUP_TIMEOUT 100UL /*!< Time out for HSE start up, in ms */ 105 #endif /* HSE_STARTUP_TIMEOUT */ 106 107 /** 108 * @brief Internal Multiple Speed oscillator (MSI) default value. 109 * This value is the default MSI range value after Reset. 110 */ 111 #if !defined (MSI_VALUE) 112 #define MSI_VALUE 4000000UL /*!< Value of the Internal oscillator in Hz*/ 113 #endif /* MSI_VALUE */ 114 115 /** 116 * @brief Internal High Speed oscillator (HSI) value. 117 * This value is used by the RCC HAL module to compute the system frequency 118 * (when HSI is used as system clock source, directly or through the PLL). 119 */ 120 #if !defined (HSI_VALUE) 121 #define HSI_VALUE 16000000UL /*!< Value of the Internal oscillator in Hz*/ 122 #endif /* HSI_VALUE */ 123 124 /** 125 * @brief Internal Low Speed oscillator (LSI) value. 126 */ 127 #if !defined (LSI_VALUE) 128 #define LSI_VALUE 32000UL /*!< LSI Typical Value in Hz*/ 129 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 130 The real value may vary depending on the variations 131 in voltage and temperature. */ 132 133 /** 134 * @brief External Low Speed oscillator (LSE) value. 135 * This value is used by the UART, RTC HAL module to compute the system frequency 136 */ 137 #if !defined (LSE_VALUE) 138 #define LSE_VALUE 32768UL /*!< Value of the External oscillator in Hz*/ 139 #endif /* LSE_VALUE */ 140 141 /** 142 * @brief Internal Multiple Speed oscillator (HSI48) default value. 143 * This value is the default HSI48 range value after Reset. 144 */ 145 #if !defined (HSI48_VALUE) 146 #define HSI48_VALUE 48000000UL /*!< Value of the Internal oscillator in Hz*/ 147 #endif /* HSI48_VALUE */ 148 149 #if !defined (LSE_STARTUP_TIMEOUT) 150 #define LSE_STARTUP_TIMEOUT 5000UL /*!< Time out for LSE start up, in ms */ 151 #endif /* LSE_STARTUP_TIMEOUT */ 152 153 /* Tip: To avoid modifying this file each time you need to use different HSE, 154 === you can define the HSE value in your toolchain compiler preprocessor. */ 155 156 /* ########################### System Configuration ######################### */ 157 /** 158 * @brief This is the HAL system configuration section 159 */ 160 #define VDD_VALUE 3300U /*!< Value of VDD in mv */ 161 #define TICK_INT_PRIORITY ((1uL <<__NVIC_PRIO_BITS) - 1uL) /*!< tick interrupt priority (lowest by default) */ 162 #define USE_RTOS 0U 163 #define PREFETCH_ENABLE 0U 164 #define INSTRUCTION_CACHE_ENABLE 1U 165 #define DATA_CACHE_ENABLE 1U 166 167 /* ########################## Assert Selection ############################## */ 168 /** 169 * @brief Uncomment the line below to expanse the "assert_param" macro in the 170 * HAL drivers code 171 */ 172 /* #define USE_FULL_ASSERT 1 */ 173 174 /* ################## SPI peripheral configuration ########################## */ 175 176 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 177 * Activated: CRC code is present inside driver 178 * Deactivated: CRC code cleaned from driver 179 */ 180 181 #define USE_SPI_CRC 1U 182 183 /* ################## CRYP peripheral configuration ########################## */ 184 185 #define USE_HAL_CRYP_SUSPEND_RESUME 1U 186 187 /* Includes ------------------------------------------------------------------*/ 188 /** 189 * @brief Include module's header file 190 */ 191 #ifdef HAL_DMA_MODULE_ENABLED 192 #include "stm32wlxx_hal_dma.h" 193 #endif /* HAL_DMA_MODULE_ENABLED */ 194 195 #ifdef HAL_ADC_MODULE_ENABLED 196 #include "stm32wlxx_hal_adc.h" 197 #endif /* HAL_ADC_MODULE_ENABLED */ 198 199 #ifdef HAL_COMP_MODULE_ENABLED 200 #include "stm32wlxx_hal_comp.h" 201 #endif /* HAL_COMP_MODULE_ENABLED */ 202 203 #ifdef HAL_CORTEX_MODULE_ENABLED 204 #include "stm32wlxx_hal_cortex.h" 205 #endif /* HAL_CORTEX_MODULE_ENABLED */ 206 207 #ifdef HAL_CRC_MODULE_ENABLED 208 #include "stm32wlxx_hal_crc.h" 209 #endif /* HAL_CRC_MODULE_ENABLED */ 210 211 #ifdef HAL_CRYP_MODULE_ENABLED 212 #include "stm32wlxx_hal_cryp.h" 213 #endif /* HAL_CRYP_MODULE_ENABLED */ 214 215 #ifdef HAL_DAC_MODULE_ENABLED 216 #include "stm32wlxx_hal_dac.h" 217 #endif /* HAL_DAC_MODULE_ENABLED */ 218 219 #ifdef HAL_EXTI_MODULE_ENABLED 220 #include "stm32wlxx_hal_exti.h" 221 #endif /* HAL_EXTI_MODULE_ENABLED */ 222 223 #ifdef HAL_FLASH_MODULE_ENABLED 224 #include "stm32wlxx_hal_flash.h" 225 #endif /* HAL_FLASH_MODULE_ENABLED */ 226 227 #ifdef HAL_GPIO_MODULE_ENABLED 228 #include "stm32wlxx_hal_gpio.h" 229 #endif /* HAL_GPIO_MODULE_ENABLED */ 230 231 #ifdef HAL_GTZC_MODULE_ENABLED 232 #include "stm32wlxx_hal_gtzc.h" 233 #endif /* HAL_GTZC_MODULE_ENABLED */ 234 235 #ifdef HAL_HSEM_MODULE_ENABLED 236 #include "stm32wlxx_hal_hsem.h" 237 #endif /* HAL_HSEM_MODULE_ENABLED */ 238 239 #ifdef HAL_I2C_MODULE_ENABLED 240 #include "stm32wlxx_hal_i2c.h" 241 #endif /* HAL_I2C_MODULE_ENABLED */ 242 243 #ifdef HAL_I2S_MODULE_ENABLED 244 #include "stm32wlxx_hal_i2s.h" 245 #endif /* HAL_I2S_MODULE_ENABLED */ 246 247 #ifdef HAL_IPCC_MODULE_ENABLED 248 #include "stm32wlxx_hal_ipcc.h" 249 #endif /* HAL_IPCC_MODULE_ENABLED */ 250 251 #ifdef HAL_IRDA_MODULE_ENABLED 252 #include "stm32wlxx_hal_irda.h" 253 #endif /* HAL_IRDA_MODULE_ENABLED */ 254 255 #ifdef HAL_IWDG_MODULE_ENABLED 256 #include "stm32wlxx_hal_iwdg.h" 257 #endif /* HAL_IWDG_MODULE_ENABLED */ 258 259 #ifdef HAL_LPTIM_MODULE_ENABLED 260 #include "stm32wlxx_hal_lptim.h" 261 #endif /* HAL_LPTIM_MODULE_ENABLED */ 262 263 #ifdef HAL_PKA_MODULE_ENABLED 264 #include "stm32wlxx_hal_pka.h" 265 #endif /* HAL_PKA_MODULE_ENABLED */ 266 267 #ifdef HAL_PWR_MODULE_ENABLED 268 #include "stm32wlxx_hal_pwr.h" 269 #endif /* HAL_PWR_MODULE_ENABLED */ 270 271 #ifdef HAL_RCC_MODULE_ENABLED 272 #include "stm32wlxx_hal_rcc.h" 273 #endif /* HAL_RCC_MODULE_ENABLED */ 274 275 #ifdef HAL_RNG_MODULE_ENABLED 276 #include "stm32wlxx_hal_rng.h" 277 #endif /* HAL_RNG_MODULE_ENABLED */ 278 279 #ifdef HAL_RTC_MODULE_ENABLED 280 #include "stm32wlxx_hal_rtc.h" 281 #endif /* HAL_RTC_MODULE_ENABLED */ 282 283 #ifdef HAL_SMARTCARD_MODULE_ENABLED 284 #include "stm32wlxx_hal_smartcard.h" 285 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 286 287 #ifdef HAL_SMBUS_MODULE_ENABLED 288 #include "stm32wlxx_hal_smbus.h" 289 #endif /* HAL_SMBUS_MODULE_ENABLED */ 290 291 #ifdef HAL_SPI_MODULE_ENABLED 292 #include "stm32wlxx_hal_spi.h" 293 #endif /* HAL_SPI_MODULE_ENABLED */ 294 295 #ifdef HAL_SUBGHZ_MODULE_ENABLED 296 #include "stm32wlxx_hal_subghz.h" 297 #endif /* HAL_SUBGHZ_MODULE_ENABLED */ 298 299 #ifdef HAL_TIM_MODULE_ENABLED 300 #include "stm32wlxx_hal_tim.h" 301 #endif /* HAL_TIM_MODULE_ENABLED */ 302 303 #ifdef HAL_UART_MODULE_ENABLED 304 #include "stm32wlxx_hal_uart.h" 305 #endif /* HAL_UART_MODULE_ENABLED */ 306 307 #ifdef HAL_USART_MODULE_ENABLED 308 #include "stm32wlxx_hal_usart.h" 309 #endif /* HAL_USART_MODULE_ENABLED */ 310 311 #ifdef HAL_WWDG_MODULE_ENABLED 312 #include "stm32wlxx_hal_wwdg.h" 313 #endif /* HAL_WWDG_MODULE_ENABLED */ 314 315 /* Exported macro ------------------------------------------------------------*/ 316 #ifdef USE_FULL_ASSERT 317 /** 318 * @brief The assert_param macro is used for function's parameters check. 319 * @param expr If expr is false, it calls assert_failed function 320 * which reports the name of the source file and the source 321 * line number of the call that failed. 322 * If expr is true, it returns no value. 323 * @retval None 324 */ 325 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 326 /* Exported functions ------------------------------------------------------- */ 327 void assert_failed(uint8_t* file, uint32_t line); 328 #else 329 #define assert_param(expr) ((void)0U) 330 #endif /* USE_FULL_ASSERT */ 331 332 #ifdef __cplusplus 333 } 334 #endif 335 336 #endif /* STM32WLxx_HAL_CONF_H */ 337 338 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 339