Home
last modified time | relevance | path

Searched refs:Y (Results 1 – 20 of 20) sorted by relevance

/arch/arm/cpu/armv7/
A DKconfig17 Say Y here to enable support for booting in non-secure / SVC mode.
24 Say Y here to boot in secure mode by default even if non-secure mode
78 Say Y here to boot in hypervisor (HYP) mode when booting non-secure.
85 Say Y here to enable PSCI support.
119 Say Y here to use the long descriptor page table format. This is
/arch/mips/mach-octeon/include/mach/
A Docteon-model.h215 #define __OCTEON_MATCH_MASK__(X, Y, Z) \ argument
218 typeof(Y) y = (Y); \
/arch/arm/cpu/armv8/
A DKconfig23 Say Y here if there is not any trust firmware to set
48 Say Y here to support "spin-table" enable method for booting Linux.
87 Say Y here to support this framework in SPL phase.
93 Say Y here to save SPL data section for cold boot, and restore
109 Say Y here when the endianness of the register or memory holding the
139 Select Y here to make use of PSCI calls for system reset
150 Say Y here to enable PSCI support on ARMv8 platform.
/arch/arm/
A DKconfig.debug7 Say Y here to include definitions of printascii, printch, printhex
18 Say Y here if you wish the debug print routes to direct
A DKconfig444 Say Y here to enable it
461 Say Y here if you want to enable ARM SMC Calling Convention.
/arch/arm/mach-sc5xx/
A DKconfig141 expression `sf probe X:Y`
148 This is the SPI chip select number to use for booting, Y in the
149 expression `sf probe X:Y`
156 expression `sf probe X:Y`
162 This is the OSPI chip select number to use for booting, Y in the
163 expression `sf probe X:Y`
/arch/arm/dts/
A Dimx6q-gw54xx.dts67 * and Y[11:4] across 16bits in the same cycle
A Dlpc3250-ea3250.dts148 /* 3-axis accelerometer X,Y,Z (or AD-IN instead of Z) */
A Dimx6qdl-hummingboard2.dtsi283 * i.e. The mapping of GPIO(X,Y) to Linux gpio
284 * number is : gpio number = (X-1) * 32 + Y
A Dzynqmp-sck-kv-g-revA.dtso10 * "Y" - A01 board modified with legacy interposer (Nexperia)
A Dtegra30-lg-x3.dtsi926 usif-gpios = <&gpio TEGRA_GPIO(Y, 3) GPIO_ACTIVE_HIGH>;
1108 gpio = <&gpio TEGRA_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
A Dimx6qdl-gw551x.dtsi458 * and Y[11:4] across 16bits in the same cycle
A Dtegra30-htc-endeavoru.dts956 /* PORT Y */
/arch/arm/mach-uniphier/
A DKconfig92 Say Y to use the on-board UART, Ether, LED devices.
/arch/arm/mach-sunxi/
A DKconfig951 Say Y here to enable support for the gpio pins of the axp PMIC ICs.
957 Say Y here to prevent the device from booting up because of a plug-in
978 Say Y here to add support for using a graphical console on the HDMI,
987 Say Y here to add support for outputting video over HDMI.
993 Say Y here to add support for outputting video over VGA.
999 Say Y here to add support for external DACs connected to the parallel
1007 Say Y here if you've a board which uses opendrain drivers for the vga
1024 Say Y here to add support for outputting composite video.
/arch/riscv/
A DKconfig164 If you say Y here, then the code size will be increased due to
175 If you say Y here, then the code size will be increased due to
399 machine. If you say Y here, U-Boot will run on many, but not
410 machine. If you say Y here, U-Boot SPL will run on many, but not
/arch/arm/mach-tegra/
A DKconfig274 re-cryption was created. If your device was re-crypted choose Y.
/arch/arm/mach-omap2/am33xx/
A DKconfig246 If you want RTC-DDR ONLY Support, say Y. RTC Only with DDR in
/arch/arm/mach-rockchip/
A DKconfig621 Say Y here to prevent the device from booting up because of a plug-in
683 If unsure, say Y.
/arch/arm/mach-imx/mx6/
A DKconfig107 Say "Y" if your board uses dynamic (per-boot) DDR calibration.

Completed in 42 milliseconds