Searched refs:build (Results 1 – 25 of 27) sorted by relevance
12
| /arch/arm/mach-bcm283x/ |
| A D | Kconfig | 73 This option creates a build targeting the ARM1176 ISA.
89 This option creates a build targeting the ARMv7/AArch32 ISA.
112 This option creates a build targeting the ARMv7/AArch32 ISA.
116 bool "Raspberry Pi 3 32-bit build"
128 This option creates a build targeting the ARMv7/AArch32 ISA.
132 bool "Raspberry Pi 3 64-bit build"
156 This option creates a build targeting the ARMv8/AArch64 ISA.
160 bool "Raspberry Pi 4 32-bit build"
175 This option creates a build targeting the ARMv7/AArch32 ISA.
179 bool "Raspberry Pi 4 64-bit build"
[all …]
|
| /arch/arm/dts/ |
| A D | xenguest-arm64.dts | 5 * This is required to make the board build with CONFIG OF_SEPARATE
|
| A D | octeontx.dts | 5 * This is required to make the board build with CONFIG OF_SEPARATE
|
| A D | bcm7xxx.dts | 5 * This is required to make the board build with CONFIG OF_SEPARATE
|
| A D | r9a06g032-rzn1-snarc-u-boot.dtsi | 6 * tools/binman/binman build -d arch/arm/dts/r9a06g032-rzn1-snarc.dtb -O <outdir>
|
| A D | bcm2835-rpi-a.dts | 62 /* Binary number representing build/revision */
|
| A D | bcm2835-rpi-b.dts | 63 /* Binary number representing build/revision */
|
| A D | r8a779g0-u-boot.dtsi | 49 * this system uses PIE build
|
| /arch/x86/include/asm/ |
| A D | cb_sysinfo.h | 168 char *build; member
|
| /arch/arm/mach-sunxi/ |
| A D | rmr_switch.S | 27 @ This file is not build by the U-Boot build system, but provided only as a
|
| /arch/mips/ |
| A D | Kconfig | 219 Choose this option to build an U-Boot for release 1 through 5 of the
227 Choose this option to build an U-Boot for release 2 through 5 of the
235 Choose this option to build an U-Boot for release 6 or later of the
244 Choose this option to build a kernel for release 1 through 5 of the
253 Choose this option to build a kernel for release 2 through 5 of the
262 Choose this option to build a kernel for release 6 or later of the
365 The build will fail and a valid size suggested if this is too small.
|
| /arch/arc/ |
| A D | Kconfig | 37 Choose this option to build an U-Boot for ARC750D CPU.
44 Choose this option to build an U-Boot for ARC770D CPU.
|
| /arch/arm/cpu/armv8/fsl-layerscape/doc/ |
| A D | README.qspi | 31 To get the QSPI image, build u-boot with QSPI config, for example,
|
| A D | README.lsch3 | 183 To form the NAND image, build u-boot with NAND config, for example,
240 To form the SD-Boot image, build u-boot with SD config, for example,
|
| A D | README.falcon | 146 build. For example, if Linux expect Ethernet PHY to be initialized in U-Boot
|
| /arch/x86/cpu/apollolake/ |
| A D | Kconfig | 104 be able to compare booting speed with the same build. Enable this to
|
| /arch/arm/mach-zynqmp/ |
| A D | Kconfig | 136 The load address for the BL31 image. This value is used to build the
143 The load address for the BL32 image. This value is used to build the
|
| /arch/riscv/dts/ |
| A D | openpiton-riscv64.dts | 7 * are automatically generated by the OpenPiton build system and
|
| /arch/riscv/ |
| A D | Kconfig | 203 Choose this option to build U-Boot for RISC-V M-Mode.
209 Choose this option to build U-Boot for RISC-V S-Mode.
221 Choose this option to build U-Boot SPL for RISC-V M-Mode.
226 Choose this option to build U-Boot SPL for RISC-V S-Mode.
|
| /arch/ |
| A D | Kconfig | 380 This option should contain the architecture name to build the
387 This option should contain the CPU name to build the correct
396 This option should contain the SoC name to build the directory
|
| /arch/x86/ |
| A D | Kconfig | 97 Select to build a U-Boot capable of supporting Intel MID
168 # is normally a 64-bit build.
272 The build system will take care of creating a u-boot.rom file
430 perferred base address specified during the FSP build. Use Intel's
453 perferred base address specified during the FSP build. Use Intel's
1040 Select this option to provide code to a build generic WiFi ACPI table
1060 display, memory and build information. It is stored in
1071 display, memory and build information. It is stored in
|
| /arch/x86/lib/coreboot/ |
| A D | cb_sysinfo.c | 336 cb_parse_string(ptr, &info->build); in cb_parse_header()
|
| /arch/arm/mach-k3/ |
| A D | Kconfig | 130 The load address for the ATF image. This value is used to build the
|
| /arch/arm/mach-sc5xx/ |
| A D | Kconfig | 123 The image built by the ADI ADSP Linux build system.
|
| /arch/arm/ |
| A D | Kconfig | 469 Use this flag to build U-Boot using the Thumb instruction set for
479 Use this flag to build SPL using the Thumb instruction set for
489 Use this flag to build TPL using the Thumb instruction set for
2264 build system (to create signed boot images that can be
|
Completed in 682 milliseconds
12