Home
last modified time | relevance | path

Searched refs:which (Results 1 – 25 of 59) sorted by relevance

123

/board/sunxi/
A DKconfig9 which is compatible with the normal boot ROM (NBROM).
17 which is compatible with the secure boot ROM (SBROM).
/board/intel/minnowmax/
A DKconfig21 # Enable Winbond so we can use Dediprog em100pro emulator which does
/board/toradex/colibri-imx6ull/
A DKconfig12 256MB or 512MB module which do have raw NAND on-module.
18 1GB module which does have eMMC on-module.
/board/congatec/conga-qeval20-qa3-e3845/
A DREADME11 provides this console on the UART0 which is provided via a Winbond
19 which is routed from the QSeven SoM to the X300 connector on the
/board/warp7/
A DKconfig15 which gets converted into a root=PARTUUID=some_uuid.
/board/sandbox/
A Dsandbox.env18 * These are used for distro boot which is not supported. But once bootmethod
/board/toradex/colibri_imx7/
A DKconfig11 256MB or Colibri iMX7D 512MB module which do have raw NAND
18 1GB module which does have eMMC on-module.
/board/toradex/apalis-tk1/
A DKconfig33 left disabled in the device tree which needs changing as well for this
/board/phytec/pcm058/
A DREADME81 which in turn contains the UBI volumes "fit" (which contains the kernel fit-
82 image) and "root" (which contains a ubifs root filesystem).
88 which kernels using CONFIG_HIGHMEM=y may not be able to access during early
/board/toradex/apalis_t30/
A DKconfig31 disabled in the device tree which needs changing as well for this to
/board/raspberrypi/rpi/
A Dsdhc.asl58 // sd card, which is marked as non-removable.
98 // sd card, which is marked as non-removable.
/board/emulation/
A DKconfig15 There are two types of x86 boards supported by QEMU which are
/board/synopsys/emsdp/
A DREADME13 possible configuration which means the same one binary will work on more
18 - The first channel is used for serial debug port (which makes it possible
38 It contains a checksum which makes this saved environment invalid in
/board/hisilicon/hikey/
A Dbuild-tf.mak20 @which $(CROSS_COMPILE)gcc > /dev/null ; \
/board/eets/pdu001/
A DKconfig24 The PDU001 has a bi-color (red/green) LED labeled 'Run' which
/board/gateworks/gw_ventana/
A DREADME15 The i.MX6 has a BOOT ROM PPL (Primary Program Loader) which supports loading
25 - u-boot.img - The main U-Boot core which is u-boot.bin with a image header.
58 and bad block information (referred to as 'bootstreams') which are replicated
64 The Freescale 'kobs-ng' application from the Freescale LTIB BSP, which runs
76 The kobs-ng application uses an imximage which contains the Image Vector Table
82 The u-boot.img, which is the non SPL U-Boot binary appended to a U-Boot image
95 The above assumes the default Ventana partitioning scheme which is configured
161 which allows the SPL to boot directly to an OS instead of to U-Boot
176 OS load time which defeats the purpose of Falcon mode in the first place.
185 that is stored on your boot medium along with the kernel (which can be any
[all …]
/board/google/
A DKconfig32 i5 Ivybridge which is a die-shrink of Sandybridge, with 4GB of
69 C ports which can support charging and up to a 4K external display.
77 This is a version of Samus which boots into TPL, then to SPL and
/board/davinci/da8xxevm/
A DREADME.da8507 bootloader which executes upon reset is the ROM Boot Loader (RBL) and sits
20 section, which is used by the RBL to load the image. At the end of the
31 Logic PD boards, or other boards which store the ethernet MAC address at
127 For this case, CONFIG_TEXT_BASE=0x60000000 which is the address to
128 which the bootloader jumps when powered on.
/board/freescale/ls2080ardb/
A DREADME25 - One port of 40-bits (8-bits ECC) DDR4 which supports four chip-selects
126 Booting Linux flavors which do not support 48-bit VA (< Linux 3.18)
128 One needs to use appropriate bootargs to boot Linux flavors which do
/board/intel/
A DKconfig23 mini-ITX form factor containing the Intel Braswell SoC, which has
55 This is the Intel Galileo board, which is the first in a family of
83 which is generated by Slim Bootloader for its driver initialization.
/board/toradex/common/
A DKconfig11 software and contains the serial number (out of which the MAC
72 Set to 0 on modules which have no 2nd instance.
/board/solidrun/clearfog/
A DKconfig8 default which uses the ClearFog Pro.
46 Select function for SerDes 0 which is shared between CON3 and CON18
/board/ti/common/
A DKconfig5 Evaluation Boards which have I2C based EEPROM detection
/board/synopsys/iot_devkit/
A DREADME19 prompt which might be used for U-Boot environment fine-tuning, manual
24 - The first channel is used for serial debug port (which makes it possible
44 It contains a checksum which makes this saved environment invalid in
57 A non-volatile memory from which ARC core may execute code directly.
/board/ea/mx7ulp_com/
A Dimximage.cfg54 * Default PFD0 divide is 27, which generates:
58 * use a divider of 30 (0x1E), which gives:

Completed in 46 milliseconds

123